Extech SDL350 Bruksanvisning
Extech
Vindmätare
SDL350
Läs nedan 📖 manual på svenska för Extech SDL350 (10 sidor) i kategorin Vindmätare. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/10
Hot Wire 5
User's Guide
Hot Wire Thermo-Anemometer
with Datalogger
Model SDL350
2
SDL350-EU-EN-V1.2-11/11
1
2
3
4
5
Hot Wire 5
1
2
11
3
4
5
6
7
8
9
10
16
15
14
13
12
18
17
19
20
Introduction
Congratulations on your purchase of the Extech SDL350 Hot Wire Thermo-Anemometer
Datalogger. This meter displays and stores air velocity and temperature readings. Temperature
readings from the thermometer built into the probe or from an externally connected type K or J
thermocouple temperature probe can be displayed and recorded. Data is stored on an SD card for
transfer to a PC. This meter is shipped fully tested and calibrated and, with proper use, will provide
years of reliable service.
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must refer to the
manual for further information.
Description
METER AND HOT WIRE PROBE
1. Thermocouple input
2. Hot Wire input plug
3. Display for air velocity and air ow readings
4. Units of measure
5. HOLD / Backlight key
6. MAX-MIN key
7. SET and Clock key
8. PC interface jack
9. Reset key
10. Power Adaptor jack
11. SD card slot
12. ENTER and LOG key
13. Down arrow and FUNCTION key ▼
14. Up arrow and UNIT key ▲
15. Power ON-OFF key
16. Temperature reading with units of measure
17. Hot Wire probe cable
18. Telescoping probe handle
19. Protective cover (sensors underneath)
20. Colored dot must face air ow
HOT WIRE PROBE TOP (detail)
1. Air stream must face into colored dot
2. Air velocity sensor
3. Sliding protective cover OPEN position
4. Sliding protective cover CLOSED position
5. Temperature sensor
NOTES:
Battery compartment, tilt stand, and tripod mount are located on the rear of the instrument.
Items 8, 9, and 10 are located behind the snap-o compartment cover on right side of meter.
3
SDL350-EU-EN-V1.2-11/11
Operation
Power ON-OFF
Power the meter ON or OFF by pressing and holding the power key for at least 1.5 seconds.
Meter Functions
This meter has three modes of operation: Air velocity (with temperature), thermocouple
temperature, and Air Volume (CFM/CMM). Press and hold the FUNCTION key for at least 1.5
seconds to switch from one mode to the other.
• Air Velocity plus Temperature mode; meter displays icon. An
• Type K or J thermocouple temperature mode (meter displays icon). tP
• Air Flow (Volume CFM/CMM) meter displays F-US or depending how the meter is set up F-EU
for units of measure for area; refer to the SETUP mode for details.
Air Velocity plus Temperature Mode
1. Select the Air Velocity and Temperature mode as described above.
2. Connect the vane probe to the meter’s probe jack (top right of meter) via the probe plug.
3. Hold the probe by its handle and allow the air ow to enter the sensor area. Note that the air
ow must face the probe’s colored dot.
4. The meter will display the air velocity measurement (upper display area) and the air
temperature (lower display area).
Changing the Air Velocity Unit of Measure
This meter oers ve (5) units of measure selections for air velocity: m/s (meters per second), FPM
(feet per minute), Km/h (kilometers per hour), knots, and mph (miles per hour).
1. Press and hold the UNIT key for at least 1.5 seconds to switch from one unit of measure to
another.
2. Note that pressing and holding the UNIT key continuously allows for quicker scrolling. Release
the key when the desired unit of measure is displayed.
Thermcouple (Type J or K) Temperature Mode
1. Select the Thermocouple Temperature mode using the FUNCTION button as described above.
2. The meter will display a ‘J’ or a ‘K’; on the left side of the display indicating the selected type.
To change the thermocouple type, refer to the Setup Mode section.
3. Connect a Type J or Type K thermocouple to the meter’s sub-miniature thermocouple jack (top
of meter on the left).
4. Hold the thermocouple in the air in the area to be tested.
5. The meter will display the thermocouple temperature in the main display area.
6. To change the temperature unit of measure (°C and °F) refer to the Setup Mode section.
Produktspecifikationer
| Varumärke: | Extech |
| Kategori: | Vindmätare |
| Modell: | SDL350 |
Behöver du hjälp?
Om du behöver hjälp med Extech SDL350 ställ en fråga nedan och andra användare kommer att svara dig
Vindmätare Extech Manualer
16 Augusti 2024
12 Augusti 2024
Vindmätare Manualer
Nyaste Vindmätare Manualer
18 September 2024
26 Augusti 2024
20 Augusti 2024
12 Augusti 2024
11 Augusti 2024
5 Augusti 2024
1 Augusti 2024
28 Juli 2024