Extech SDL800 Bruksanvisning

Extech Mätutrustning SDL800

Läs nedan 📖 manual på svenska för Extech SDL800 (10 sidor) i kategorin Mätutrustning. Denna guide var användbar för 16 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/10
USER GUIDE
Vibration Meter
SD Card real-time datalogger
Model SDL800
2 SDL800-en-GB_V1.4 6/15
Introduction
Congratulations on your purchase of the Extech SDL800 Vibration Meter. This meter displays and
stores vibration readings of Acceleration, Velocity and Displacement. Supported measurement units
are meters/s2, ft/s2, g, mm/s, cm/s, in/s, mm and inch. Logged data readings are stored on an SD
card for transfer to a PC. This meter is shipped fully tested and calibrated and, with proper use, will
provide years of reliable service.
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must refer to the
manual for further information.
Meter Description
1. Vibration pickup input jack
2. Measurement Display
3. HOLD and Backlight key
4. Power ON-OFF key
5. Up arrow ▲ / UNIT key
6. Down arrow ▼ / Function key
7. ENTER and LOG key
8. SD card slot
9. Vibration pickup
10. DC Adaptor socket, Reset key
and Data output jack
11. SET and Clock key
12. MAX-MIN key
13. Unit of measure Display
Notes: Items listed in “10” are located behind the snap-off compartment cover on meter’s right side.
Battery compartment, tilt stand, and tripod mount are located on the rear of the instrument
3 SDL800-en-GB_V1.4 6/15
Getting Started
Power ON-OFF
Power the meter by pressing and holding the power button for at least 1.5 seconds.
Press and hold the power button for at least 1.5 seconds to power OFF the meter.
This meter is powered by six (6) 1.5VDC ‘AA’ batteries or by optional AC adaptor. If the meter
will not switch ON please check that fresh batteries are installed in the rear battery compartment
or, in the case of the AC adaptor, check that the adaptor is connected correctly to the meter and
to an AC source.
Display Backlight
To turn the display backlight ON or OFF, press and hold the backlight button for at least 1.5
seconds. The meter will beep when switching the backlight ON or OFF unless the beeper is
disabled.
Vibration Sensor
Connect the vibration pickup to the cable supplied. Make sure it is firmly attached.
Connect the cable to the meter by attaching it to the BNC connector on the top of the meter.
If the surface to be tested is magnetic, attach the magnetic base to the vibration pickup and attach
the pickup to a flat surface.
If the surface to be tested is not magnetic, hold the pickup against the surface. Do not hold the
cable while making measurements.
Units of Measure
The currently selected unit of measure is shown on the meter’s LCD. To change the unit of
measure, press and hold the UNIT button until the desired unit of measure appears and then
release the UNIT button. The meter begins scrolling through the available units of measure after the
UNIT button has been depressed for at least 1.5 seconds. The saved units will become the default
turn-on units.
UNIT DISPLAY INDICATOR
ACC m/s2
g
VEL mm/s
cm/s
DISP p-p mm
ACC ft/s2
VEL In/s
DISP p-p inch

Produktspecifikationer

Varumärke: Extech
Kategori: Mätutrustning
Modell: SDL800

Behöver du hjälp?

Om du behöver hjälp med Extech SDL800 ställ en fråga nedan och andra användare kommer att svara dig


Mätutrustning Extech Manualer

Extech

Extech 380941 Bruksanvisning

23 Oktober 2024
Extech

Extech 380926 Bruksanvisning

23 Oktober 2024
Extech

Extech PRC20 Bruksanvisning

25 September 2024
Extech

Extech PRC30 Bruksanvisning

25 September 2024
Extech

Extech SD900 Bruksanvisning

25 September 2024
Extech

Extech PRC15 Bruksanvisning

25 September 2024
Extech

Extech 412300A Bruksanvisning

25 September 2024
Extech

Extech 412400 Bruksanvisning

25 September 2024
Extech

Extech 433201A Bruksanvisning

25 September 2024
Extech

Extech SD910 Bruksanvisning

25 September 2024

Mätutrustning Manualer

Nyaste Mätutrustning Manualer

PCE Instruments

PCE Instruments PCE-PMI 1 Bruksanvisning

14 Januari 2025
PCE Instruments

PCE Instruments PCE-324 Bruksanvisning

14 Januari 2025
PCE Instruments

PCE Instruments PCE-TC 32N Bruksanvisning

14 Januari 2025
PCE Instruments

PCE Instruments PCE-ACO 9500 Bruksanvisning

14 Januari 2025
Klein Tools

Klein Tools CL810 Bruksanvisning

14 Januari 2025
Klein Tools

Klein Tools CL710 Bruksanvisning

14 Januari 2025
Ebro

Ebro PHT 830 Bruksanvisning

13 Januari 2025
Gossen Metrawatt

Gossen Metrawatt PROFiTEST H+E EASY CHECK Bruksanvisning

10 Januari 2025
PCE Instruments

PCE Instruments PCE-VT 3950S Bruksanvisning

9 Januari 2025
PCE Instruments

PCE Instruments PCE-VT 3750S Bruksanvisning

9 Januari 2025