Extron IN1806 Bruksanvisning

Extron Inte kategoriserad IN1806

Läs nedan 📖 manual på svenska för Extron IN1806 (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/6
1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
IN1806 • Setup Guide
The Extron IN1806 is a six input seamless scaling presentation switcher that supports signal resolutions up to 4K @ 60 Hz at
4:4:4. It features DisplayPort and HDMI inputs, an HDMI output, and a mirrored Extron DTP2 output for extending video, audio,
and control signals up to 330 feet (100 meters) over a shielded CATx cable. The IN1806 delivers high image quality, fast and
reliable switching, Extron ProDSP audio processing, seamless video transition effects, logo keying, and HDMI loop-out. The
scaler can be controlled and congured over Ethernet, RS-232, or USB.
This guide provides instructions for an experienced user to set up and congure the IN1806 scaler. It covers how to perform basic
setup operations using the front panel controls and selected Simple Instruction Set (SIS™) commands.
NOTES:
• For full installation, configuration, menus, connector wiring, and operation details, see the IN1806 and IN1808 Series
User Guide at www.extron.com.
• The IN1806 can also be configured via the Extron Product Configuration Software (PCS), available at
www.extron.com. For information on using PCS, see the IN1806 and IN1808 Series Help File.
Installation
Rear Panel Features
100-240V 0.7A MAX ~
31
2
5
4 6
HDMI/CEC
INPUT S AUDIO INPUTS OUTPUT S REMOTE
OVER TP
IN1806
1A 1B
S IG LINK
OUT T x Rx
RS-232
GT x Rx
IR
G
RESET
1 2
3 4
+48V
+48V
1
2
MIC/LINE
L R
AUX
3 4
LAN
LOOP OUT
A C H
M
N
B D E F G I JKL
O
OUTPUTS (DT P2/XTP/HDBT)
50-60 Hz
A AC power connector
B DisplayPort input connector (input 1)
C HDMI (with CEC) loop out connector
D HDMI (with CEC) output connector (1A)
E DTP2/XTP/HDBaseT (with CEC)
output connector (1B)
F Over TP IR pass-through connector
G Analog line audio inputs 3 and 4
H Analog mic/line audio inputs 1 and 2
and adjacent phantom power LEDs
I Analog line audio outputs 1 through 4
J LAN connector
K Remote RS-232 port
L Reset LED
M Reset button
N Aux mono or stereo analog
line audio input connector
O HDMI inputs 2 through 6
Figure 1. Rear Panel Connectors — IN1806
Mounting and Cabling
Step 1 Mount the device—
a. Turn off or disconnect all equipment power sources.
b. Mount the IN1806 to a rack using the pre-installed side mounting brackets, or remove the brackets and use an optional
19-inch kit for under-desk mounting (see the instructions provided with the mounting kit, available at www.extron.com).
Step 2 Connect inputs—
a. Make the following video input connections as needed:
• Connect a DP source to the Input 1 DisplayPort connector (see figure 1, B).
• Connect digital HDMI or DVI (with an appropriate adapter) sources to HDMI input connectors 2 through 6 (O).
b. Connect analog audio sources to:
• The 5-pole captive screw line audio input connectors 3 and 4 (G) and the Aux connector (N) for balanced or
unbalanced stereo audio. The Aux Line input (N) is shared and can be associated with one or more video inputs.
• Connect balanced or unbalanced mic or line level inputs to 3-pole Mic/Line captive screw connectors 1 and 2 (H).
These inputs support optional +48 VDC phantom power, which is indicated by the LEDs at the left of the connectors.
2
IN1806 • Setup Guide (Continued)
Step 3 Connect outputs—
Make the following output connections as needed:
• Connect an HDMI, or DVI with an appropriate adapter, display to HDMI/CEC output connector 1A (see figure 1, D, on the
previous page). Connect a display to the HDMI Loop Out connector (C).
• Connect a DTP/XTP matrix switcher/HDBaseT compatible receiver to output connector 1B (E). For cable wiring and
recommendations, see “Twisted Pair Recommendations for DTP, XTP, and HDBaseT Communication.”
• Connect balanced or unbalanced analog audio output devices to one or both 5-pole captive screw output connector pairs 1
and 2, or 3 and 4 (I) (see on the next page for more information).Audio Wiring
To pass infrared data, connect a control device to the 3-pole IR Over DTP captive screw connector (see , IR Over TP Wiring
on the next page). Alternatively, insert RS-232 communication to a DTP/HDBaseT endpoint via Ethernet (see the IN1806 and
IN1808 Series User Guide for more information).
Step 4 — Connect control devices
• To control the IN1806 through Ethernet, connect a LAN or WAN to the RJ-45 LAN connector (
J). To wire the RJ-45
connector to the cable, see “Twisted Pair Recommendations for DTP, XTP, and HDBaseT Communication.” The default IP
address of the scaler is 192.168.254.254, the default subnet mask is 255.255.255.0, and the default gateway address is
0.0.0.0.
• For serial RS-232 control, connect a host device to the 3-pole captive screw connector (K). The default baud rate is 9600.
• For control through USB, connect a host device to the front panel USB mini-B port (see figure 2, A, on the next page).
Step 5 Connect power—
Connect a 100 to 240 VAC, 50-60 Hz power source to the AC power connector (see figure 1, A, on the previous page).
Twisted Pair Recommendations for DTP, XTP, and
HDBaseT Communication
Extron recommends using the following practices to achieve full transmission distances
and reduce transmission errors:
• Use Extron XTP/DTP 24 SF/UTP cable for the best performance. At a minimum,
Extron recommends 24 AWG, solid conductor, STP cable with a minimum bandwidth
of 400 MHz.
• Terminate cables with shielded connectors to the TIA/EIA-T568B standard (shown at
right).
• Limit the use of more than two pass-through points, which may include patch points,
punch down connectors, couplers, and power injectors. If these pass-through points
are required, use shielded couplers and punch down connectors.
ATTENTION:
• Do not connect these connectors to a computer or telecommunications network.
• Ne connectez pas ces ports à des données informatiques ou à un réseau de télécommunications.
• DTP remote power is intended for indoor use only. No part of the network that uses DTP remote power should be
routed outdoors.
• L’alimentation DTP à distance est destiné à une utilisation en intérieur seulement. Aucune partie du réseau qui utilise
l’alimentation DTP à distance ne peut être routée en extérieur.
NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:
• Do not exceed 40% fill capacity in conduits.
• Do not comb the cable for the first 20 meters, where cables are straightened, aligned, and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
• Separate twisted pair cables from AC power cables.
Firmware Updates
Download rmware updates from the Extron website and upload them via the internal web pages or PCS.
TIA/EIA-T568B
Pin Wire Color
1 White-orange
2 Orange
3 White-green
4 Blue
5 White-blue
6 Green
7 White-brown
8 Brown
1 2 3 4 5 6 7 8
RJ-45
Connector
Insert istedTw
Pair Wires
Pins:
3
Audio Wiring
Wire the audio input and output connectors as shown at right. Use
the supplied tie wrap to strap the audio cable to the extended tail
of the connector.
ATTENTION:
• For unbalanced outputs, do not connect wires to the
“-” poles (see the illustration at right).
• Pour les sorties asymétriques, ne connectez pas de
câbles aux pôles «-» (voir l’illustration de droite).
NOTE: The length of exposed wires is critical. The ideal length
is 3/16 inch (5 mm).
IR Over TP Wiring
To transmit and receive IR signals, connect a control device to the
three-pole Over TP IR connector (G, Tx, and Rx).
NOTE: RS-232 data can be inserted via Ethernet only (see the
IN1806 and for details).IN1808 Series User Guide
Front Panel Overview
AF
C
BG
DE H
Figure 2. Front Panel Features — IN1806
A Cong port C button E and buttons
G knob and LEDs
B Input selection buttons D and LEDs F Navigation buttons H knob and LEDs
A — Connect a host device to the USB mini-B port for device configuration, control, file Front panel configuration port
transfers, and firmware upgrades.
B — Press one of these buttons to select an input. The buttons light amber for audio and video, Input selection buttons (1-6)
green for video only, or red for audio only.
C — Press this button to enable or disable the most recently selected logo slot. Press and hold the button to Logo button
select logo slot 1 through 6 using the input selection buttons (slots 7-16 are available via SIS commands only). See the
IN1806 and IN1808 Series User Guide at www.extron.com for more information about logos.
D Signal and Status LEDs
• Input signal LEDs — These six LEDs light green for their corresponding inputs when active video content is detected
on that input.
• Output signal LEDs — Output LEDs 1A, 1B, and Loop light green when active video is being output, and blink amber
when output video and sync are disabled.
• Input HDCP LEDs — These six LEDs light green for each input signal that is HDCP-encrypted.
• Output HDCP LEDs — These three LEDs light green for an output when it is currently HDCP-encrypted.
• DTP2 and DTP Output LEDs — These LEDs light green if DTP or DTP2 power has been enabled on DTP output 1B.
E — Press these buttons to access and navigate the on-screen display (OSD) menu system.Menu and Enter buttons
F — Press these buttons to navigate through the on-screen display menu system or change settings.Navigation buttons
G — Rotate the knob to adjust the microphone level. The eight LED indicators light according to Mic knob and LED indicators
the level being adjusted. The LEDs light in order from bottom to top to indicate steps from 1% (-99 dB) to 99% (-1 dB). The
bottom LED blinks when the volume is muted. The top LED blinks when the volume is at 100% (0 dB).
H Volume knob and LED indicators — Rotate the knob to adjust the program or output volume level.
Balanced Audio Output
Tip
Ring
Tip
Ring
Slee
ves
Unbalanced Audio Output
Tip
No Ground Here
No Ground Here
Tip
Slee sve
L R
L R
Unbalanced Audio InputBalanced Audio Input
Tip
Ring
Tip
Ring
Slee sve
Tip
Sleeve
Sleeve
Tip
L R
L R
Do not tin the wires!
A
udio Inputs and Outputs 1 – 4 and xAu
Mic/Line Inputs 1 and
2
Balanced Audio Input
Tip
Sleeve
Ring
Unbalanced Audio Input
Tip
Sleeve

Produktspecifikationer

Varumärke: Extron
Kategori: Inte kategoriserad
Modell: IN1806

Behöver du hjälp?

Om du behöver hjälp med Extron IN1806 ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad Extron Manualer

Extron

Extron PI 115 Bruksanvisning

27 Oktober 2024
Extron

Extron XTP DTP 24 Bruksanvisning

27 Oktober 2024
Extron

Extron IN1608 XI Bruksanvisning

26 Oktober 2024
Extron

Extron FOX II RS 104 Bruksanvisning

26 Oktober 2024
Extron

Extron DTP T UWP 4K 232 D Bruksanvisning

1 Oktober 2024
Extron

Extron FOX Matrix 7200 Bruksanvisning

26 September 2024
Extron

Extron EWB 210 Series Bruksanvisning

26 September 2024
Extron

Extron EDID 101D Bruksanvisning

26 September 2024
Extron

Extron FMR 206 Bruksanvisning

26 September 2024
Extron

Extron EWB Series Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024