Extron QC 101 C Bruksanvisning

Extron Inte kategoriserad QC 101 C

Läs nedan 📖 manual på svenska för Extron QC 101 C (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
1
QC 101 Controller • Setup Guide
This setup guide provides basic instructions for an
experienced user to install the QC 101 Controller. For
additional information and detailed procedures, see
the and the Quantum User Guide Quantum Control
Software User Guide, available at www.extron.com.
The Extron QC 101 E and QC 101 C are dedicated
controllers for the Quantum® Elite and Quantum
Connect videowall processors. They feature an
embedded operating system and the Quantum Control
Software preinstalled on the internal drive. The QC 101
provides an alternative to a traditional PC to program
congurations and control the Quantum processors.
ATTENTION:
• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and
national building codes and electrical codes.
• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes
du bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
NOTE: For full installation, configuration, and operation details, see the , which is provided with the Quantum User Guide
Quantum on the Extron Videowall Processing disc and is also available at www.extron.com.
Rear Panel Features and Connections
G
AAA
100-240V ~ 0.5A MAX
50-60Hz
DISPLAYPORT 1
A B RGBHV
RS-232
Tx Rx G
RESET
2
1
2
HDMI
OUTPUTS
USB LAN OUTPUTS
REMOTE
B C D E F
H
3
POWER
Figure 1. QC 101 Rear Panel
A AC power connector — Connect to an AC power
source.
B DisplayPort output connector — (Optional)
C USB connectors — Connect to a mouse, keyboard,
or flash drive. Connector 1 (top) accepts USB 2.0
signals and connector 2 accepts USB 3.0.
D A and B LAN ports — Connect to a network or the
Quantum processor. These two RJ-45 connectors
support 10/100/1000 Base-T.
E RGBHV output connector — (Optional) 15-pin VGA
F Remote RS-232 connector — Connect to a control
system for RS-232 communication.
G Power button — Using a small screwdriver or stylus,
press this recessed button momentarily to safely shut
down the controller. Pressing and holding the button for
4 seconds forces a hard shutdown of the QC 101.
H HDMI output connector — (Optional)
NOTE: The button and LED labeled RESET are not functional.
Installation Steps
1. Disconnect power from all equipment.
2. (Optional) Mount the unit to a rack or furniture, following the instructions provided with the mounting hardware. Rack
and furniture mounting kits are available at www.extron.com.
3. Connect a display to the DisplayPort, VGA, or HDMI output connector (see gure 1,
B, E, or H).
QC 101 • Setup Guide (Continued)
2
4. Connect the keyboard, mouse, and flash drive (if needed) to the rear panel USB ports (
C) to create and save Quantum
Elite or Connect configuration project files (see the , available at Quantum Control Software User Guide www.extron.com).
5. Connect a straight-through Ethernet cable between QC 101 LAN port A or B (see figure 1,
D, on the previous page)
and the network or the Control connector on the rear panel of the Quantum chassis. If connecting through a LAN, ensure that
the QC 101 is on the same subnet as the Quantum processor or processors.
6. Connect a control device (such as an Extron IPCP or IPL Pro) to the Remote RS-232 port (F) for remote
control of the Quantum system using R-type commands (see the , available at Quantum Control Software User Guide
www.extron.com, for more about these commands).
7. Connect AC power to the QC 101 rear panel IEC connector (see A). Connect power to all other devices in the system.
8. Power on the Quantum chassis and all other connected devices.
100-240V ~ --A MAX
50/60 Hz
OUT PUT S
OUT PUT S
REMOT E
US B LAN
DIS PLAYPO RT
13
A B RGBHV
RS232
T x Rx G
RESET PO WER
2
HDM I
Control
VLAN
Ethernet
Ethernet
Ethernet
RS-232
HDMI
HDMI
HDMI
USB USB
Mouse
Display
Keyboard HDMI
Extron
Quantum t Connec
HDCP ompliant-C l Vide alow
Processin Systg em
Ext
ron I o 0PCP Pr 25
IP ink L o l Pr Contro Processor
Extron
QC 1 C10
Controller for
Quantum Connect QUANTUM CO NNECT 408
VIDEO WALL PROCESS OR
DATA
1000
LINK
ACT
RIR
IPCP PRO 250
eBUS
OVER
LIMITS
COM
I/O
1
2
2
4
1
321
RT S
CT S
T x
Rx
RELAYSIR/S
Sources
Displays
Figure 2. QC 101 Connection Example with a Quantum Connect
NOTE: The QC 101 front panel has no controls that are involved in setup. It contains four indicator LEDs that provide status
for power and booting (Power), disk drive activity (SSD), and network activity (LAN A and LAN B). The USB Config port is
reserved for future use.
Configuring the QC 101
After all rear panel connections have been made and all connected devices are powered on, you are ready to congure the
QC 101 to manage the Quantum processors. To do this, set the IP address of the QC 101, then either create a project le using
the Quantum Control Software (loaded on the QC 101 prior to delivery) or upload an existing project le that was congured using
a computer.
Setting the IP Address of the QC 101
The QC 101 controller is a host device with an embedded operating system. To communicate with the Quantum processor, the
QC 101 must be on the same network and subnet as all the Quantum processors in the system. To set the QC 101 IP address,
you need a keyboard and mouse connected to one or both of the USB ports and a monitor connected to one of the output ports.
1. Do either of the following:
zOn the QC 101 screen, click the icon (shown at right), or
zOn the desktop screen, double-click the shortcut icon on the desktop.
The window opens.
3
2. Right-click the name of the LAN port in use (highlighted and no red ) and select from the pop-up menu.
Figure 3. Selecting a LAN Port
3. On the window, scroll to locate and select the
checkbox (see 1 in
the illustration at right), and click (2).
4. In the Internet
window, enter the desired QC 101 IP address parameters and click
. The IP address must be on the as those of the same subnet
Quantum processors.
5. In the window (which opened at the same time as the
window in step 1), click the
button (see gure 4, 1).
Figure 4. Click Commit C Drive on the QC 101 Shell Window
6. On the conrmation prompt that opens, click to save the address changes to the hard drive and reboot the controller. A
password prompt is displayed. Enter the password where indicated on the prompt and click .
ATTENTION:
• Do not power off or reset the QC 101 while it is rebooting.
• Veuillez éteindre ni réinitialiser le QC 101 lors du redémarrage.ne pas
Setting Up the Quantum Control Software
To use the Quantum software to congure and control the processor, start by setting up a project (presentation), in which you
dene the processor, select or create a layout, set up video sources, and create multiple scenes.
NOTE: The C: drive on the QC 101 is write-protected. Therefore, files located on the C: drive that are created or changed are
not saved when power is cycled to the QC 101. Save any new or changed projects on the controller to the QC 101 internal
D: drive or to a flash drive attached to one of the USB ports on the QC 101 rear panel.
1. Create a new project or upload an existing one.
zIf creating a new project, see the for detailed instructions. Save the project to Quantum Control Software User Guide
the QC 101 D: drive and double-click its lename to open the project.
zIf uploading an existing project that was created on a PC, copy the project le directly to the QC 101 D: drive and
double-click its lename to open the project.

Produktspecifikationer

Varumärke: Extron
Kategori: Inte kategoriserad
Modell: QC 101 C

Behöver du hjälp?

Om du behöver hjälp med Extron QC 101 C ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad Extron Manualer

Extron

Extron PI 115 Bruksanvisning

27 Oktober 2024
Extron

Extron XTP DTP 24 Bruksanvisning

27 Oktober 2024
Extron

Extron IN1608 XI Bruksanvisning

26 Oktober 2024
Extron

Extron FOX II RS 104 Bruksanvisning

26 Oktober 2024
Extron

Extron DTP T UWP 4K 232 D Bruksanvisning

1 Oktober 2024
Extron

Extron FOX Matrix 7200 Bruksanvisning

26 September 2024
Extron

Extron EWB 210 Series Bruksanvisning

26 September 2024
Extron

Extron EDID 101D Bruksanvisning

26 September 2024
Extron

Extron FMR 206 Bruksanvisning

26 September 2024
Extron

Extron EWB Series Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024