Fluke 7102 Bruksanvisning

Fluke Temperaturregulator 7102

Läs nedan 📖 manual på svenska för Fluke 7102 (6 sidor) i kategorin Temperaturregulator. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/6

Introduction

The Fluke Calibration 7102/7103 Micro-Bath (The Product) is a portable and bench-top

temperature calibrator that calibrates thermocouple and RTD temperature probes. For complete

Product use instructions, download the 7102 User’s Guide or the 7103 User’s Guide from

www.flukecal.com.

Note

The Product CD no longer ships with these Products.

Contact Fluke Calibration

Fluke Corporation operates worldwide. For local contact information, go to our website:

www.flukecal.com

To register your product, view, print, or download the latest User’s Guide or manual supplement, go

to our website.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

+1-425-446-5500

info@flukecal.com

7102/7103

Micro-Bath

Safety Information

1-year limited warranty. See the User’s Guide for the full warranty.

PN 5311971

August 2021

All product names are trademarks of their respective companies.

7102/7103

Safety Information

More specific safety information is listed in the User’s Guide where applicable.

A Warning identifies hazardous conditions and procedures that are dangerous to the user.

XW Warning

To prevent possible electrical shock, fire, or personal injury:

• Read all safety information before you use the Product.

• Carefully read all instructions.

• Use this Product indoors only.

• Do not use the Product if it operates incorrectly.

• Follow local regulations regarding use with toxic, flammable, corrosive, or

otherwise hazardous fluids. Incorrect product installation, abuse, or damage can

lead to operator exposure to these fluids. Limit hazardous-fluid exposure to

permitted levels in case of leakage or rupture.

• Do not operate the Product in an excessively wet, oily, dusty, or dirty environment.

• Do not use the Product if it is altered or damaged.

• Disable the Product if it is damaged.

• Replace the mains power cord if the insulation is damaged or if the insulation

shows signs of wear.

• Make sure that the power cord is positioned in such a way as it cannot contact hot

surfaces or temperature probes. Always inspect power cord before use for any

damage to the insulation due to contact with hot surfaces, cuts or abrasions.

• Do not alter the Product and use only as specified, or the protection supplied by

the Product can be compromised.

• Do not use the Product around explosive gas, vapor, or in damp, dusty, or wet

environments.

• Do not use the Product above its rated frequency.

• Connect an approved three-conductor mains power cord to a grounded power

outlet.

• Do not put the Product where access to the mains power cord is blocked.

• Make sure that the space around the Product meets minimum requirements. Leave

at least 15 cm (6 inches) of clearance around the Product.

• Do not use an extension cord or adapter plug.

• Do not keep the Product in operation and unattended at high temperatures.

• Turn the Product off and remove the mains power cord. Stop for two minutes to let

the power assemblies discharge before you open the fuse door.

• Replace a blown fuse with exact replacement only for continued protection

against arc flash.

• Turn off the Product and remove the mains power cord. Stop for 2 minutes to let

the internal circuits discharge before you open the fuse door or remove Product

covers.

• Have an approved technician repair the Product.

Micro-Bath

Safety Information

• Do not install an access cover without holes onto a bath that is energized.

Dangerous pressures may result from fluid vaporizing.

• Do not use the Product for any application other than calibration work. The

Product is for temperature calibration only. Any other use of the unit may cause

unknown hazards to the user.

• To move the Product, lift the Product by the handle provided. Do not move the

Product until the display reads <25 °C (77 °F) and the Product has been drained or

the transport lid installed.

• Always ensure the Product is cool before you close it for storage.

• Do not touch the well access surface of the Product.

• Do not mix water and oil when exceeding temperatures of 90 °C (194 °F). The

temperature of the well access is the same as the actual temperature shown on

the display. For example, if the Product is set at 125 °C (257 °F) and the display

reads 125 °C, the well is at 125 °C (257 °F).

• Do not operate near flammable materials. Extreme temperatures could ignite the

flammable material.

• The top sheet metal of the Product may exhibit extreme temperatures for areas

close to the well access.

• Do not turn off the unit at temperatures >100 °C (212 °F). This could create a

hazardous situation. Select a set-point <100 °C (212 °F) and allow the Product to

cool before you turn it off.

• Do not remove the fluid at high temperatures. The fluid will be the same

temperature as the display temperature.

• Use of this Product at high temperatures for extended time periods requires

caution.

• Always operate this Product at room temperatures listed in Environmental

Conditions in the User’s Guide.

• Overhead clearance is required. Do not place the Product under a cabinet or other

structure.

• Use a ground fault interrupt device.

• Fluids may expand at different rates. Allow for fluid expansion inside the well by

Keeping the fluid level at least 1.9 cm (0.75 inches) below the top of the well at all

times.

Produktspecifikationer

Varumärke:	Fluke
Kategori:	Temperaturregulator
Modell:	7102
LED-indikatorer:	LAN, Link, Power
Anslutningsteknik:	Bedraad
Antal Ethernet LAN (RJ-45)-portar:	1
Anslutning för nätadapter:	Ja
Nätverksstandard:	IEEE 802.3x
Förvaringstemperatur:	-25 - 70 °C
Internera:	Nee
Våglängd:	1300 nm
Ethernet-gränssnittstyp:	Fast Ethernet
Maximal dataöverföringshastighet:	- Mbit/s
Auto MDI/MDI-X:	Ja
Mått (B x D x H):	120 x 88 x 25 mm
Maximal-räckvidd:	2000 m
Drifttemperatur (TT):	0 - 40 °C
Relativ luftfuktighet i drift (VV):	10 - 90 procent
Fiberoptisk kontakt:	SC
Omvandlarens ingångsgränssnitt:	100Base-TX, 10Base-T
Konverterns utgångsgränssnitt:	100Base-FX
Fiberkanalportar:	1
Struktur för trådläge:	Multimode