Frigidaire IMKTF20A Bruksanvisning

Läs nedan 📖 manual på svenska för Frigidaire IMKTF20A (9 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/9
AUTOMATIC ICE MAKER
INSTALLATION INSTRUCTIONS
P/N: A22932801
WARNING
To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator
from electrical power before connecting a water supply line to the refrigerator.
Connect the ice maker to a potable water supply only.
Ice Maker (IMKTF20A) Kit Components
Tools Needed:
Flat head screw driver Phillips or Quadrex driver
¼" Hex driver Gloves
Drill Needle nose pliers
Plastic putty knife
NOTE
Check with your local building authority for recommendations on water lines and associated materials prior
to installing your new refrigerator. For household water line hookup from the home water supply system to
the unit, we recommend for homes with existing valves Smart Choice® water line kit 5304437642 (with a 6
Stainless Steel Water Line) and for homes without an existing valve, we recommend Smart Choice® water
line kit 5304493869 (with a 6� Polyline Waterline). Please refer to Frigidaire.com for more information.
Water Valve
QTY: 1
IMPORTANT
We recommend an authorized service technician to install the ice maker kit.
Ice Maker
QTY: 1
Ice Container
QTY: 1
Water Inlet Tube Assembly
QTY: 1
Screw (B)
QTY: 2
Screw (A)
QTY: 2
Plastic Clamp
QTY: 3
Ice Maker
Connector Cover
QTY: 1
2
Figure 4
Ice Maker Installation Instructions
1. Unplug the refrigerator from the electrical outlet.
2. Remove the spacer. Remove the freezer shelf
(some models) by pushing the shelf to the left
until the right side of the shelf comes free from
the holes. See Figure 1.
3. Use a plastic putty knife to remove the 2 plugs on
the left wall of the freezer compartment. Discard
the plugs. See Figure 3.
4. Remove the harness connector cover, where the
ice maker will plug in, with aathead screwdriver.
Discard the harness connector cover. See Figure 3.
NOTE
Some models have two plugs on the left freezer wall
that must be removed. These holes will be used to
mount the Ice Maker. (You will also insert the Water
Inlet Tube in the plug on the back wall.)
5. Place two, long, ice maker mounting screws ( ) A
into freezer wall where plugs were removed
in Step 3. Turn each screw clockwise until " ½
remains out. See Figure 4.
NOTE
You will need both hands to hook up and secure
the Ice Maker to the freezer wall. DO NOT let the
Ice Maker dangle free after the wiring harness is
plugged into the connector on the back freezer wall.
7. Place the ice maker harness into the cover.
See Figure 6.
6. Unhook one loop of the ice maker harness.
See Figure 5.
Figure 3
Figure 5
Figure 6
Then slowly lift up and pull the shelf free from the
holes on the right side. See Figure 2.
Figure 1
Figure 2
A
3
Ice Maker Installation Instructions
11. Mount the ice maker to the side wall with the 2
screws ( ). Tighten the screws to secure the ice A
maker in place. See Figure 10.
12. Reinstall the freezer shelf in the lower position.
Place the ice container on the shelf. See Figure 11.
9. Slide the ice maker connector cover over the
connector (hook on left A, snap on right B).
See Figure 8.
A
A
B
Figure 8
Figure 11
8. Connect the ice maker connector into the mating
connector mounted on the back freezer panel.
See Figure 7.
Figure 7
10. Slide the ice maker onto the back screw. See
Figure 9A. Then slide the ice maker down onto
the front screw. See Figure 9B.
Figure 9A
Figure 9B
Figure 10
A
A

Produktspecifikationer

Varumärke: Frigidaire
Kategori: Inte kategoriserad
Modell: IMKTF20A

Behöver du hjälp?

Om du behöver hjälp med Frigidaire IMKTF20A ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Frigidaire Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer