GE GHDA485NCS Bruksanvisning

GE tvättmaskin GHDA485NCS

Läs nedan 📖 manual på svenska för GE GHDA485NCS (16 sidor) i kategorin tvättmaskin. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/16

GE Consumer & Industrial

Appliances

ilt-In Dishwasher

f you have questions, call 800.GE.CARES (800.432.27

37) or visit our website at

: www.ge.com

IMPORTANT

– The dishwasher MUST be installed

to allow for future removal from the enclosure if service is

required.

f you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories – See the Owner’s Manual for available

custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS shown

throughout these instructions. While performing

installations described in this booklet, gloves, safety glasses

or goggles should be worn.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

IMPORTANT

– Observe all governing codes and

ordinances.

•

Note to Installer

– Be sure to leave these instructions for the

consumer’s and local inspector’s use.

•

Note to Consumer

– Keep these instructions with your

Owner’s Manual for future reference.

•

Skill Level

– Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills.

Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the GE Appliance Warranty. See warranty information.

•

Completion Time – 1 to 3 Hours

. New installations require

more time than replacement installations.

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

TOOLS YOU WILL NEED:

Phillips head screwdriver

1/4" and 5/16" nutdriver

6" Adjustable wrench

Level

Carpenters square

Measuring tape

Safety glasses

Flashlight

Bucket to catch water when ﬂ ushing the line

15/16" socket (optional for skid removal)

Gloves

For New Installations Only:

Tubing cutter

Drill and appropriate bits

Hole saw set

90° Elbow,

Ferrule and

Compression Nut

Wire Nuts (3)

Waste Tee

Electrical Cable

(or Power Cord, if applicable)

Hot Water Line

Hand

Shut-Off

Valve

Side and Top Trim Pieces on some models

Hole Saw Set

Level

Thread

Seal Tape

Air Gap

Strain Relief

Drain Hose

Hose Clamp

1/4" and 5/16"

Nutdriver

15/16" Socket

Bucket

Tubing Cutter

Drill and Bits

Flashlight

Gloves

Phillips

Head

Screwdriver

Carpenters

Square

Adjustable

Wrench

Safety Glasses

Installation Preparation

Drain Hose Hanger

Measuring Tape

PARTS SUPPLIED

IN INSTALLATION PACKAGE:

Two #8-18 x 5/8" Phillips special head screws, to

secure dishwasher to underside of countertop.

Junction box cover and #10 hex head screw

Hose Clamp

Drain hose (approximately 78" long)

Drain hose hanger

Side and top trim pieces (some models)

Literature, samples and/or coupons

MATERIALS YOU WILL NEED:

Ferrule, compression nut and 90° Elbow (3/8"NPT

external thread on one end, opposite end sized

to fit water supply)

Thread seal tape

UL Listed wire nuts (3)

GPF65 side mount kit if countertop is

granite or similar material

Materials Needed for

New Installations:

Air gap for drain hose, if required

Waste tee for house plumbing, if applicable

Electrical cable or power cord

Screw type hose clamp

Strain relief for electrical connection

Hand shut-off valve (recommended)

Water line–3/8" minimum copper tubing

GPF10L drain hose

(10' long

)

, if needed

Junction

Box Cover

GPF65

Side-Mount

Bracket Kit

#8 Phillips

Special

Head Screws

5/8" long

Screw Kit

#10

Hex- Head

J-Box Screw

1/2" long

Optional

10' Drain Hose

GPF10L

Hose Clamp

Method 1 – Air Gap with Waste Tee or Disposer

An air gap must be used when required by local codes and ordi-

nances. The air gap must be installed according to manufacturer’s

instructions.

PREPARE DISHWASHER ENCLOSURE

• The rough cabinet opening must be at least 24" deep, 24"

wide and approximately 34-1/2" high from floor to underside

of the countertop.

CLEARANCES:

When

installed into a corner,

allow 2" min. clearance

between dishwasher

and adjacent cabinet,

wall or other appliances.

Allow 28-3/8" min. clear-

ance from the front of

the dishwasher for door

opening. Figure B

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 10' distance to drain.

NOTE:

Air gap must be used, if waste tee or disposer

connection is less than 18" above floor to prevent siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following

questions.

Do local codes or ordinances require an air gap?

Is waste tee less than 18" above floor?

If the answer to either question is YES, Method 1 MUST

be used.

• If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2" diameter hole in the cabinet wall within

the shaded areas shown in Figure A for the drain hose

connection. The hole should be smooth with no sharp edges.

IMPORTANT

–

When

connecting drain line to disposer,

check to be sure that drain plug has

been removed. DISHWASHER WILL

NOT DRAIN IF PLUG IS LEFT IN PLACE.

Method 2 – “High Drain Loop” with Waste Tee or Disposer

Tip: Avoid unnecessary service call charges

Always be sure disposer drain plug has been removed before

attaching dishwasher drain hose to the disposer.

Figure D

• The dishwasher must be installed so that drain hose is no

more than 10' in length for proper drainage.

• The dishwasher must be fully enclosed on the top, sides and

back, and must not support any part of the enclosure.

24"

Min.

This Wall Area

must be Free

of Pipes or

wires

Plumbing and Electric Service

Must Enter Inside This Area

34-1/2"1/4"

Underside of

Countertop

to Floor

24"

Min.

5" 5"

Cabinets

Square

and

Plumb

Floor MUST be Even

With Room Floor.

32"

Min.

18"

Min.

Drain Hose Hanger

Figure B

Clearance for Door

Opening 2" Minimum

Countertop

Dishwasher

28-3/8"

Figure A

Figure C

Installation Preparation

Remove

Drain

Plug

WARNING

To reduce the risk of electric shock,

ﬁ re, or injury to persons, the installer

must ensure that the dishwasher is

completely enclosed at the time of

installation.

32"

Min.

18"

Min.

Drain Hose Hanger

Produktspecifikationer

Varumärke:	GE
Kategori:	tvättmaskin
Modell:	GHDA485NCS
Färg på produkten:	Zwart
Bredd:	220 mm
Djup:	110 mm
Höjd:	290 mm
Användarmanual:	Ja
Placering:	Binnen
Typ av strömkälla:	AC
Medföljande kablar:	Coaxiaal
Inkluderar AC-adapter:	Ja
Digitalt signalformat:	DVB-T, DVB-T2
Antennförstärkningsnivå (max):	44 dBi
Impedans:	75 Ohm
Frekvensomfång:	87.5 - 230
Anslutning(ar):	IEC
Frekvensband som stöds:	DAB, FM, UHF, VHF
Frequentie bereik:	470 - 790 MHz
AC-ingångsspänning:	230 V
Antennkabellängd:	1.5 m
LTE-/GSM-filter:	Ja
BADDA:	Ja