GE Profile PDWT502VII Bruksanvisning

GE tvättmaskin Profile PDWT502VII

Läs nedan 📖 manual på svenska för GE Profile PDWT502VII (3 sidor) i kategorin tvättmaskin. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/3

Dimensions and Installation Information (in inches)

For answers to your Monogram,

® Profile™

Series or GE® appliance questions, visit our

website at geappliances.com or call GE

Answer Center® service, 800.626.2000.

As an ENERGY STAR®

partner, GE has determined

that this product meets the

ENERGY STAR guidelines

for energy efficiency.

Specification Revised 3/13 250244

Listed by

Underwriters

Laboratories

This wall area

must be free of

pipes or wires

Countertop

Hot

water

line on

left

2Plumbing and electrical

service must enter

inside shaded area

24" From wall

24" MIN.

90°

19" MIN. from wall

24"

MIN.

34" to 34-3/4"

Underside

of countertop

to floor

5 5

90°

Electrical

wiring on

right

Electrical

wiring is

3" from

cabinet

Electrical Rating

Voltage AC.......................................................... 120

Hertz..................................................................... 60

Total connected load amperage............. 9.9

Calrod® heater watts max........................ 875

For use on adequately wired 120-volt,

15-amp circuit having 2-wire service

with a separate ground wire. This appliance

must be grounded for safe operation.

Installation Information: Before installing,

consult installation instructions packed with

product for current dimensional data.

††† Add 3/4" for custom panel and additional

room for custom handle

An installation template is packed with these

models and may be obtained in advance.

Order Pub. No. 5-X063.

PDWT502VII

GE Profile™ Series Dishwasher with SmartDispense™ Technology

Listed by

Underwriters

Laboratories

As an ENERGY STAR®

partner, GE has determined

that this product meets the

ENERGY STAR guidelines

for energy efficiency.

GE Pub. No. 031-30569-1

Custom Dishwasher Door Panel Template

Top of Panel Top of Panel

Trim Around Dotted Line

11-5/16"

Trim Around Dotted Line

2-9/32"

25-9/16"

11-5/16"

2-9/32"

25-9/16"

Trim Around Dotted LineTrim Around Dotted Line

Drill 3/32"

Pilot Hole

3/32" Deep

Drill 3/32"

Pilot Hole

3/32" Deep

Drill 3/32"

Pilot Hole

3/32" Deep

Drill 3/32"

Pilot Hole

3/32" Deep

3/4" Thick Custom Panel

Template Instructions for

Top Control Integrated Profile and

Monogram Dishwasher Models

T he custo m pa nel should be size d t o your installat ion situatio n. See Step 1. For easier

insta llat ion t he custom pa nel and cust om handle should be attached before installing the

dishwas her. Use t his t emplat e t o locate mount ing screws and spa cers on the custom panel.

IMPO ANTRT

• A cust om handle must be inst alle d ont o t he cust om

panel. Inst all t he cust om handle 4-1/2" max. from

t he t op of t he pan el .

STEP 2 DRAW CENTERLINE

• P lace the custom panel on a flat surface with appearance side

down.

• Locate the vertical center of the panel at the top.

• Use a carpenters square to draw a centerline from top to bottom.

STEP 4 INSTALL MOUNTING SCREWS AND SPACERS

Mark Center

Screw H ol es

STEP 5 INSTALL CUSTOM HANDLE

A custom handle must be installed onto the panel

before the panel is secured to the dishwasher door.

• T he handle should be installed so that it aligns with

adjacent drawer handles, or 4-1/2" max. from the

top of the panel. Secure the handle in the same

manner as cabinet handles. Screws must be

countersunk into the panel.

STEP 6 INSTALL ASSEMBLED PANEL

• Secure the panel to the door by inserting the top

and bottom mounting screws with spacers into

the matching keyhole slots.

• Make sure all 4 spacers engage the keyhole slots.

• P ress the panel against the door and push

downward until the spacers are f ully engaged

into the key hole slots. The panel should align

evenly with the top and sides.

• Stand the dishwasher upright.

• Open dishwasher door and drive the supplied

#8 x 1-3/4" truss head screws. Drive one screw at

the top and one on each side as shown, through

the inner door and into the custom panel.

WARNING: Do not overtighten screws. Excessive

tightening of the screws could damage door edges.

STEP 3 ALIGN TEMPLATE TO PANEL

• T rim template on the dotted line along all sides.

• P lace the template on the panel aligned with the top edge and

the centerline. Use tape to hold in place.

IMPO RT ANT: If t he templa te is not aligned with the t op edge o f the

panel, the 1/2" minimum ga p will not be maint ained. T his 1/2" minimum

gap must be maint ained t o prevent condensa tion and dama ge to the

co ntro l panel f rom sc rew heads.

• Use an awl to mark the screw hole locations indicated on the

template. Remove the template.

HEIGHT

Panel height must be between 30-1/16" and 30-1/4" .

• If the panel height is more than 30-1/4" it will

prevent the door from swinging open.

• If the panel height is less than 30-1/16" it will not

cover the dishwasher door frame.

Minimu m 1/2" Gap

for Cle arance

Cou nterto p

1/2" min.

PART S INC LUDED:

(4) Spa ce rs

(4) #8 x 5/8" Phillips t russ hea d st a inl ess st e el screws

(3) #8 x 1-3/4" Phil lips t russ hea d st a inl ess st e el

wood scr e ws

(2) Hea vy dut y springs

STEP 1 CUSTOM PANEL SIZE REQUIREMENTS

If the panel is less than 3/4" thick, shorter screws must

be used. Use #8 x 1/2" screws for 1/2" thick panels (not supplied).

• Use a 3/32" drill bit to drill pilot holes 3/32" deep in the marked

locations.

Note : T he custom panel is secured to the dishwasher door with

the spacers and screws provided. The spacer will slip into the

keyhole slots on the dishwasher door.

• Drive the supplied #8 x 5/8" Phillips truss head steel screws

through the spacer and into the panel.

• Install remaining spacers and screws as indicated in the marked

locations.

4-1/2" M ax.

Fr om Top

of Panel

Han dle

Cu stom

Door Panel

Screws Mu st

Be Countersu nk

In to Pan el

Cu stom

Panel

Sh ou lder Washers

Engage Keyhole

Slots

Dish wash er

Door

Cu stom

Panel

Screw

Spacer

IMPO RT AN ensur e optimum door balanc eT: T o

perf ormance, the c ustom pa nel must not weigh mo re

tha n 14 lbs.

STEP 7 INSTALL DOOR SPRINGS

The dishwasher is shipped from the factory with a

temporary set of balance springs. Use the heavy duty

springs provided and the adjustment holes in the

cable to balance the door after the cus tom panel

is ins talled onto the dishwasher.

• With the dishwasher on the wood skid, close and

latch the door.

• Remove and discard both door springs.

• Attach the new heavy duty door springs. Engage

the end with the short hook into the support leg

and the long hook into the cable.

• Open and close the door.

• If the door drops open when released, increase

spring tension. If the door closes when released,

decrease tension.

T IP: If the d oor d oes no t open easil y or falls to o

qui ckly, check spring cabl e rou ting. The cable is he ld

in place by “sh oulde rs” on the pu lley. Chec k to b e

sure the c able has no t slip ped ov er the pull ey

shou lde rs.

IMPOR NTT A : Adjust both b alance spri ngs to the

sam e am ount o f tensio n to p revent excessiv e door

twistin g dur ing u se.

Corre ct Sprin g

Cable Routin g

Increase

Tension

Decrease

Tension

Pulley

Shoulder

Use T his

Mou nting

Hole

23-3/4"

30-1/16 " Min .

30-1/4" Max.

• T he top of the custom panel must be flush

with the top of the door. T he 1/2" minimum gap

between the top of the door and the bottom of the

countertop must be maintained.

WIDTH

Panel widt h must be 23-3/4" .

• If the panel width is less than 23-3/4" it will not

cover the dishwasher frame.

For Reference Only

Not to Scale

Order GE Pub. No. 031-30569-1

Call 1-800-626-2000

For a full-size panel template with complete

panel installation instructions.

PDWT502VII

GE Profile™ Series Dishwasher with SmartDispense™ Technology

Specification Revised 3/13 250244

For answers to your Monogram,

® Profile™

Series or GE® appliance questions, visit our

website at geappliances.com or call GE

Answer Center® service, 800.626.2000.

Features and Benefits

• 5-stage filtration with Piranha™ hard food disposer - 5 self-cleaning filters ensure

clean dishes

• Dedicated silverware jets - Highly pressurized spray jets target the silverware area for

improved cleaning

• Deep Clean cycle with Steam Prewash - Removes tough, baked-on soils like egg, rice

and oatmeal

• Top rack only selection - Upper rack only cycle uses less water than a full load

• Fan assist dry with heated option and ActiveVent - A heating element heats the air

inside while a hidden fan circulates the warm air to help dry dishes

• 48 dBA sound level - Nearly silent two-pump system cleans dirty dishes without

disruption

• ENERGY STAR® qualified and CEE Tier II rated - Meets or exceeds federal guidelines for

energy efficiency for year-round energy and money savings

• Eclipse black full-extension racks with ball-tip tines - Durable racks glide smoothly on

ball-bearings for easy loading

• Lower rack fold-down tines - Flexible loading options handle today's dishes and

cookware of all shapes and sizes

• SmartDispense™ technology - Conveniently stores up to 47 oz of liquid detergent and

automatically dispenses multiple doses in each cycle

• Upper rack deep bowl tines - Even oversized bowls fit perfectly in the top rack for

easy cleaning

• Flexible racks - Designed for today's dishes and holds up to 16-place settings

• Two-pump system - One small pump for washing/rinsing and one small pump to

remove soils provide excellent wash performance with reduced sound

• Model PDWT502VII - Custom panels required

PDWT502VII

GE Profile™ Series Dishwasher with SmartDispense™ Technology

Specification Revised 3/13 250244

Produktspecifikationer

Varumärke:	GE
Kategori:	tvättmaskin
Modell:	Profile PDWT502VII
Färg på produkten:	Black, Red
LED-indikatorer:	Ja
På / Av knapp:	Ja
Ethernet LAN:	Ja
Antal USB 2.0-portar:	4
VGA (D-Sub) port(ar):	1
Antal Ethernet LAN (RJ-45)-portar:	2
Typ processor:	Nee
Ethernet LAN, dataöverföringshastigheter:	10,100,1000 Mbit/s
Antal portar USB 3.2 Gen 1 (3.1 Gen 1) Typ A:	4
PCI Express-kortplatsversion:	3.0
Maximalt internminne:	64 GB
Återställningsknapp:	Ja
Bostadstyp:	Rack (4U)
ETC:	Ja
Ethernet-gränssnittstyp:	Gigabit Ethernet
Chipset moderkort:	Intel® C236
PCI Express x1 (Gen 3.x)-platser:	1
PCI Express x4 (Gen 3.x)-platser:	1
Gränssnitt för lagringsenheter som stöds:	Serial ATA, Serial Attached SCSI (SAS)
Seriell port(ar):	1
LAN-kontroller:	Intel I210
PCI Express x8 (Gen 3.x)-platser:	2
Kompatibla processorer:	Intel Core i3, Intel Pentium Dual-Core, Intel Xeon
Antal processorer som stöds:	1
Antal DIMM-platser:	4
Antal lagringsenheter som stöds:	24
Storlekar för lagringsenheter stöds:	2.5, 3.5 "
Minnestyper som stöds:	DDR4-SDRAM
Typer av lagringsenheter som stöds:	HDD & SSD