GT 916 Bruksanvisning
Läs nedan 📖 manual på svenska för GT 916 (16 sidor) i kategorin Billarm. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/16
GT915/916/917/918
INSTALLATION AND USER MANUAL
1
Getronic S.r.l.
Via Calcinate No.12
21026 Gavirate (VA) Italy
Tel. +39 0332 756011
Fax + 39 0332 731162
www.gtalarm.it
SUMMARY
1.0 - GENERAL DESCRIPTION Page 2
2.0 - INSTALLATION AND CONNECTIONS Page 3
3.0 - CONNECTION DIAGRAM Page 4
4.0 - INDICATOR COMMAND DIAGRAM Page 5
5.0 - GT931 ULTRASONIC KIT CONNECTION(only for GT915) Page 5
6.0 - CENTRAL DOOR LOCKING DIAGRAMS Page 6
7.0 - SET FUNCTIONS Page 8
8.0 - USER MANUAL Page 11
9.0 - MAINTENANCE AND WARNINGS Page 14
10.0 - COMPLIANCE DECLARATION Page 15
11.0 - TECHNICAL DATA Page 15
12.0 - WARRANTY CONDITIONS Page 16
1.0 - GENERAL DESCRIPTION
GT916 is a compact remote controlled alarm system equipped with 2 GT888 handsets
with electronic key incorporated for the emergency disarming, with universal central door
locking command, back-up battery, perimetric protection for doors/boot/bonnet, engine
immobilisation and also small in size which help with the installation.
FUNCTIONS PROGRAMMABLE OF THE SYSTEM (SET FUNCTIONS):
- HANDSETS SELF-CODING
- RAPID TEST
- COMFORT CLOSING(where appicable)
- ACOUSTIC SIGNAL WHEN ARMING/DISARMING
- INDICATOR COMMAND
- DOOR SWITCH PULSING MANAGEMENT
- POSITIVE DOORS PIN SWITCH MANAGEMENT
OTHER FUNCTIONS:
- Double door locking
- PANIC function
- ANTI-HIJACK function
- CHECK CONTROL of occurred alarms and anomalies
- Emergency disarming by handset with electronic key incorporated
2
3
2.0 - INSTALLATION AND CONNECTIONS
WARNINGS:
- Complete a pre-installation check and disconnect the negative terminal of the vehicle’s
battery. .
- Before fixing the device, insert the installation loom connectors into the alarm and
screw the connector cover on.
- Place the alarm system in the engine compartment, away from direct sources of
water spray and high tension wiring.
- Solder and isolate all connections.
- Connect the BROWN wire to the negative terminal of the vehicle’s battery (power supply
negative).
- Connect the RED (general power supply) and RED/WHITE wires (indicator relay positive)
to the positive terminal of the vehicle’s battery with a 15A fuse.
- Connect the YELLOW wire to an ignition switched live (+15/54) that remains live even
when the engine is being cranked.
- ORANGE wire (INDICATOR Command): if the INDICATOR COMMAND is DISABLED
connect to the vehicle right indicators (or to the left). If the INDICATOR COMMAND function
is ENABLED with this wire is possible to command the indicators (only on the vehicles
equipped with this function - See the INDICATOR COMMAND diagram). For the connection
refer to the technical installation guides.
- Connect the ORANGE/BLACK /wire (FEEDBACK) to the vehicle left (or right) indicator by
a diode(2 Amp) (see the INDICATOR COMMAND diagram).
- Connect the GREEN wire to the switches for the boot and bonnet protection.
- Connect the GREEN/BROWN wire to the original door pin switches. This alarm input is
set by default to manage the negative stable signals. It is possible to manage also the
vehicles original switches with negative impulsive signals(pulsing) enabling the Function
No.6 PULSING management. For the connection refer to the technical installation guides.
It is possible to manage also the positive stable signals enabling the Function No.7
Postive Door pin switch management.
- Connect the PINK wire (Positive output when the alarm is armed - Max capacity 80 mA to
the PINK wire of modules or additional sensors (i.e. ultrasonic module).
- Connect the GREEN/BLACK wire (alarm input by optional additional sensors) to the
GREEN/BLACK wire of the same (i.e. ultrasonic module).
- Connect the BROWN wire (Sec. 0,35mm²) to the modules or additional sensors (i.e.
ultrasonic module).
- The RED/BROWN, RED/GREY, RED/BLUE, YELLOW/BROWN, YELLOW/GREY and YELLOW/
BLUE wires are used to command the central door locking referring to the instuctions in
the technical installation guide.
WARNING:
- Always use 5 A fuses on the RED/BLUE and YELLOW/BLUE wires.
- The max. load to command the central door locking is 5 A. For example it is not
possible to drive directly No.4 GT71 actuators (see diagramNo. 5).
Produktspecifikationer
| Varumärke: | GT |
| Kategori: | Billarm |
| Modell: | 916 |
Behöver du hjälp?
Om du behöver hjälp med GT 916 ställ en fråga nedan och andra användare kommer att svara dig
Billarm GT Manualer
1 September 2024
Billarm Manualer
- Billarm HP
- Billarm Gemini
- Billarm Audiovox
- Billarm Viper
- Billarm Waeco
- Billarm Spy
- Billarm Jablotron
Nyaste Billarm Manualer
23 September 2024
21 September 2024
18 September 2024
18 September 2024
18 September 2024
15 September 2024
14 September 2024
10 September 2024
1 September 2024
30 Augusti 2024