Gys RT003 Start-Stop Bruksanvisning

Gys Batteriladdare RT003 Start-Stop

Läs nedan 📖 manual på svenska för Gys RT003 Start-Stop (18 sidor) i kategorin Batteriladdare. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/18

GB.1-V1

RT003 START & STOP

BATTERY & ELETRICAL SYSTEM ANALYSER

TEST PROCEDURES / OPERATING INSTRUCTIONS

IMPORTANT：

For testing 6 / 12 volt batteries and 12 / 24 volt charging

systems. (ONLY 12 volt for START & STOP battery test)

Suggested operation range 32℉(0℃) to 122℉(50℃) in

ambient temperature.

1 : Display

2 : Previous/Next keys

3 :ENTER key

GB.2-V1

WARNING：

Working in the vicinity of a lead acid battery is dangerous.

Batteries generate explosive gases during normal battery

operation. For this reason, it is of utmost importance, if

you have any doubt, that each time before using your

tester, you read these instructions very carefully.

To reduce risk of battery explosion, follow these

instructions and those published by the battery

manufacturer and manufacturer of any equipment you

intend to use in the vicinity of the battery. Observe

cautionary markings on these items.

Do not expose the tester to rain or snow.

PERSONAL SAFETY PRECAUTIONS：

Someone should be within range of your voice or close

enough to come to your aid when you work near a lead

acid battery.

Have plenty of fresh water and soap nearby in case

battery acid contacts skin, clothing or eyes.

Wear safety glasses and protective clothing.

If battery acid contacts skin or clothing, wash

immediately with soap and water. If acid enters eye,

immediately flood eye with running cold water for at least

ten minutes and get medical attention immediately.

NEVER smoke or allow a spark or flame in vicinity of

battery or engine.

Be extra cautious to reduce risk of dropping a metal tool

onto the battery. It could spark or short-circuit the battery

or other electrical parts and could cause an explosion.

Remove personal metal items such as rings, bracelets,

necklaces and watches when working with a lead acid

GB.3-V1

battery. It can produce a short circuit current high enough

to weld a ring or the like to metal causing a severe burn.

INSERTION OR REPLACEMRNT OF LEAD WIRE：

Remove the cover in the backside bottom of the battery

tester.

Insert the connectors which contain black-yellow pair and

yellow-red pair in one end of the lead wire into the

sockets which can be found when you remove the cover

as above. Be sure to make colors matched between the

connectors and sockets as shown below.

PREPARING TO TEST：

Be sure area around battery is well ventilated while

battery is being tested.

Clean battery terminals. Be careful to keep corrosion

from coming in contact with eyes.

Inspect the battery for cracked or broken case or cover. If

battery is damaged, do not use tester.

If the battery is not sealed maintenance free, add distilled

water in each cell until battery acid reaches level

specified by the manufacturer. This helps purge

excessive gas from cells. Do not overfill.

Yellow

Black white

Red (Connector)

Yellow (Socket)

Black

White

Red

Connect

(RT003 Backside)

Produktspecifikationer

Varumärke:	Gys
Kategori:	Batteriladdare
Modell:	RT003 Start-Stop
Färg på produkten:	Grijs
Användarmanual:	Ja
USB-kontakttyp:	USB Type-C
Medföljande kablar:	USB Type-A to USB Type-C, USB Type-C
Antal USB-anslutningar:	1
USB-version:	3.2 Gen 1 (3.1 Gen 1)
Plug and play:	Ja
USB-anslutning:	Ja
Inklusive skruvar:	Ja
Storlek på lagringsdisk:	M.2 "
Gränssnitt för lagringsenheter som stöds:	PCI Express
Överföringshastighet:	10 Gbit/s
Antal lagringsenheter som stöds:	1
Typ produkt:	SDD-behuizing
Kön USB-kontakt:	Vrouwelijk
Längder för lagringsenheter som stöds:	42, 60, 80 mm