Hobart HS8 Bruksanvisning
Hobart
Skärmaskin
HS8
Läs nedan 📖 manual på svenska för Hobart HS8 (1 sidor) i kategorin Skärmaskin. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/1
Disassembly for Cleaning
• Remove the Sharpener by lifting straight up.
• Remove the Meat
Grip Assembly by
loosening the Meat
Grip Slide Rod from
the Product Tray
while holding the
Meat Grip Handle.
Pull the Meat Grip
Slide Rod from the
Meat Grip Handle
and Product Tray.
• Loosen the Meat Grip Handle
and remove the Handle, Meat
Grip Arm, and Washer from
the Meat Grip.
• Pull the Product Tray toward
the operator until it stops.
Loosen the Knob on the
Support Arm.
• Tilt the Product Tray to
the right. The Product
Tray can be cleaned in
this open position, or
it can be removed by
grasping with both hands
and lifting straight up.
MEAT
GRIP
MEAT GRIP
ARM
MEAT GRIP HANDLE
WASHER
The slicer knife is sharp. Exercise extreme caution when working near the knife.
Unplug the machine power cord and turn index knob fully clockwise to close the
gauge plate before cleaning the slicer.
NOTE: Sanitizer concentration shall comply with Section 4-501.114, Manual and Mechanical Warewashing Equipment,
Chemical Sanitization – Temperature, pH, Concentration, and Hardness of the FDA Food Code. If a chemical sanitizer
other than chlorine, iodine, or quaternary ammonium is used, it shall be applied in accordance with the EPA-registered
label use instructions. In order to clean the slicer thoroughly, it is necessary to disassemble the slicer. It is recommended
that all parts be removed, cleaned, sanitized, and allowed to dry before re-assembling for use.
HS Series Slicer (Removable Knife) – Cleaning and Sanitizing Instructions
F35285 Rev. C (May 2017)
This machine must be cleaned, rinsed and sanitized at intervals to comply with national, state and/or local health codes.
Cleaning
• Wipe out any residue remaining in-
side the Sharpener housing. Wash,
rinse, and sanitize the Knife and
Knife Removal Tool, Sharpener,
Ring Guard Cover, and Top Knife
Cover in a sink or dishwasher.
• Clean the Product Tray pin with the
brush as shown.
• Wash, rinse, and sanitize the Product Tray and Meat Grip Assem-
bly in a sink. Set all parts on a clean, sanitized surface and allow
to air dry.
• To clean under the slicer, use the Cleaning Leg or Lift Assist Lever
to support the slicer.
Reassembly After Cleaning
• Orient the Knife Hub
mark to arrow as shown,
so it points to the Pin on
the Ring Guard at the 1
o’clock position.
• Place the Knife and Tool so the Pin on the Knife Removal Tool is
at the 11 o’clock position.
• Place the Slots on the Knife Removal Tool t around the three
Pins on the Ring Guard.
1:00
• Remove the Top Knife Cover by pulling on the Latch Knob. The
Top Knife Cover is held in place by a magnet under the Latch
Knob. Remove the plastic Ring Guard Cover by lifting up.
• Ensure the gauge plate is closed, then rotate the Knife by hand to
align the arrow on the Knife with the Pin on the Ring Guard at the
1 o’clock position. The ridge in the Knife Hub will also align with
the same pin.
• The Pin on the Knife Removal Tool ts the hole in the Knife at the
11 o’clock position.
• Align the 3 slots of
tool around pins.
• Align tool pin at 11:00.
• Push the handle
rmly, all the way into
the hub.
• Turn the Handle
counterclockwise until
it stops (you may experience resistance).
• Lift Knife Tool up and out.
1:00
NOTE: If the Tool does not push the pins on the back of the Knife
into the Hub, slightly nudge the Handle upwards to lock the pins
into the Knife Nut.
• Push the Handle rmly, all the way into the Hub to engage the
pins. Then, turn the Handle clockwise until it stops. You may
experience resistance when turning. The Knife is reattached. Lift
the Tool up and out.
• Install the Ring Guard Cover on the three Guide Pins.
• Position the Top Knife Cover on the lower two Guide Pins and
lower the Latch Knob until the magnet secures the Top Knife
Cover in place.
• Lower the bottom of the Support Arm onto the Carriage Hinge
Pins. Tilt the Product Tray toward the Gauge Plate. Turn the
Knob on the Support Arm until it is tight against the Support
Arm.
• Assemble the Meat Grip Assembly by placing the Washer, Meat
Grip Arm, and Meat Grip Handle on the shaft of the Meat Grip.
Tighten the Handle. Install the Meat Grip Assembly on the Prod-
uct Tray by sliding the Meat Grip Slide Rod into the Meat Grip
Handle and Product Tray. Tighten the Meat Grip Slide Rod into
the Product Tray.
• Install the Sharpener by lowering it back onto the Sharpener
Mount so the Rod and Pin on the bottom of the Sharpener t the
Slot in the Sharpener Mount.
T
H
E
N
T
U
R
N
PUSH FIRST
Produktspecifikationer
| Varumärke: | Hobart |
| Kategori: | Skärmaskin |
| Modell: | HS8 |
Behöver du hjälp?
Om du behöver hjälp med Hobart HS8 ställ en fråga nedan och andra användare kommer att svara dig
Skärmaskin Hobart Manualer
16 September 2024
16 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
Skärmaskin Manualer
- Skärmaskin Bosch
- Skärmaskin Tefal
- Skärmaskin Ade
- Skärmaskin Ariete
- Skärmaskin Bartscher
- Skärmaskin Toolland
- Skärmaskin Orbegozo
- Skärmaskin Princess
- Skärmaskin Brother
- Skärmaskin Ozito
- Skärmaskin Gude
- Skärmaskin Fagor
- Skärmaskin Severin
- Skärmaskin Gorenje
- Skärmaskin Silvercrest
- Skärmaskin Makita
- Skärmaskin FAC
- Skärmaskin Korona
- Skärmaskin Saturn
- Skärmaskin Domo
- Skärmaskin Trisa
- Skärmaskin Livoo
- Skärmaskin Skil
- Skärmaskin Hyundai
- Skärmaskin Bestron
- Skärmaskin Oster
- Skärmaskin Jata
- Skärmaskin Melissa
- Skärmaskin Magic Chef
- Skärmaskin Fritel
- Skärmaskin Russell Hobbs
- Skärmaskin Sencor
- Skärmaskin Cuisinart
- Skärmaskin Blaupunkt
- Skärmaskin Concept
- Skärmaskin Sunbeam
- Skärmaskin Hikoki
- Skärmaskin Dremel
- Skärmaskin Ernesto
- Skärmaskin Beper
- Skärmaskin Hendi
- Skärmaskin Eldom
- Skärmaskin Philco
- Skärmaskin Mach
- Skärmaskin H.Koenig
- Skärmaskin Perel
- Skärmaskin GOTIE
- Skärmaskin Beem
- Skärmaskin Exquisit
- Skärmaskin Zelmer
- Skärmaskin Nutrichef
- Skärmaskin Genius
- Skärmaskin ETA
- Skärmaskin Powerplus
- Skärmaskin Graef
- Skärmaskin Ufesa
- Skärmaskin Rommelsbacher
- Skärmaskin Wilfa
- Skärmaskin Boss
- Skärmaskin Camry
- Skärmaskin Sammic
- Skärmaskin Primo
- Skärmaskin Clas Ohlson
- Skärmaskin Gastroback
- Skärmaskin Powerfix
- Skärmaskin MPM
- Skärmaskin RGV
- Skärmaskin Team
- Skärmaskin Nevir
- Skärmaskin CaterChef
- Skärmaskin G3 Ferrari
- Skärmaskin Magimix
- Skärmaskin Efbe-schott
- Skärmaskin Gourmetmaxx
- Skärmaskin Turmix
- Skärmaskin Ritter
- Skärmaskin OXO
- Skärmaskin Cigweld
- Skärmaskin Nesco
- Skärmaskin Waves
- Skärmaskin Coline
- Skärmaskin JAC
- Skärmaskin De Buyer
- Skärmaskin Cecotec
- Skärmaskin Maruyama
- Skärmaskin RIDGID
- Skärmaskin Kalorik
- Skärmaskin Brandson
- Skärmaskin Khind
- Skärmaskin Gastronoma
- Skärmaskin Rösle
- Skärmaskin Globe
- Skärmaskin Domoclip
- Skärmaskin Emga
- Skärmaskin Baker's Mark
- Skärmaskin Avantco
- Skärmaskin Kogan
- Skärmaskin Wolfcraft
- Skärmaskin Esperanza
- Skärmaskin PowerTec Kitchen
- Skärmaskin Panduit
- Skärmaskin Thane
- Skärmaskin Berkel
- Skärmaskin Louis Tellier
- Skärmaskin GARDE
- Skärmaskin Pro-Cut
- Skärmaskin Bifinet
- Skärmaskin Jokari
- Skärmaskin Kleva
- Skärmaskin Bron-Coucke
- Skärmaskin Enkho
- Skärmaskin Backyard Pro Butcher Series
- Skärmaskin Prince Castle
- Skärmaskin Boska
- Skärmaskin Borner
- Skärmaskin Backyard Pro
- Skärmaskin Royal Catering
- Skärmaskin Tescoma
- Skärmaskin Prowork
- Skärmaskin Weston
- Skärmaskin Ovela
Nyaste Skärmaskin Manualer
7 Januari 2025
6 Januari 2025
4 Januari 2025
1 Januari 2025
1 Januari 2025
1 Januari 2025
1 Januari 2025
30 December 2025
30 December 2025
29 December 2024