Hoffer 103 Bruksanvisning

Hoffer Walkie-talkies 103

Läs nedan 📖 manual på svenska för Hoffer 103 (4 sidor) i kategorin Walkie-talkies. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

COMMUNICATOR MODEL 103

OWNER'S MANUAL AND OPERATING INSTRUCTIONS

Carefully remove your communicator from its Packing. If there is any

visible damage, do not attempt to operate this communicator. Return

it to the place of purchase.

Getting Started

1. Antenna

2. : Displays current channel selection and other radio status LCD Screen

symbols.

3. button: Allows you to change channels.Menu

4. button (VOLUME/CHANNEL): Press to adjust volume level and Down

change channels.

5. Call button: Press to transmit CALL TONES.C

6. PUSH TO TALK PTT button: Press to transmit.

7. Speaker

8. Battery Compartment (LOCATED ON THE REAR): Houses 3 x 1.5V "AAA"

alkaline batteries or 3.6V "AAA" Ni-MH rechargeable battery pack

(not included).

9. Battery Compartment Cover Latch (LOCATED ON THE REAR): Secures

Battery Compartment cover.

10. button: Used to activate/deactivate CHANNEL SCAN. Scan SC

11. : Microphone.Mic

12. button: Press to tune in and hold onto weak signals. Monitor M

13. button (VOLUME/CHANNEL): Press to adjust volume level and Up

change channels.

14. button: Used to turn LCD Screen LAMP ON/OFF. Enter/Back Light

Buttons are locked when pressed and held.

15. button: Press and hold the button to turn your unit ON/OFF. Power On/Off

16. (Transmission) (Receiving) : Illuminates red when TX /RX LED indicator

transmitting and green when receiving.

17. External Sp./Mic. Jack

18. Belt Clip (LOCATED ON THE REAR)

Communicator Controls

Figure 1. Figure 2.

Removing the Belt Clip:

1. Pull the BELT CLIP LATCH away from the

unit.

2. While pulling the BELT CLIP LATCH, push

up on the BELT CLIP to remove it from

the unit. See Figure 1.

Installing the Belt Clip:

1. Slide the BELT CLIP into the BELT CLIP

SLOT. See Figure 2.

2. A "click" indicates the BELT CLIP is locked

into position.

Battery Installation: 1. Release the BATTERY COMPARTMENT

COVER LATCH located on the rear side

of the unit (see Figure 3) and remove

the BATTERY COMPARTMENT COVER from

the BATTERY COMPARTMENT (See Figure

4).

2. Install 3x1.5V AAA alkaline batteries or

3.6V "AAA" Ni-MH rechargeable battery

pack (not included) as shown.

3. Reinstall the BATTERY COMPARTMENT

COVER and lock the BATTERY

COMPARTMENT COVER LATCH into

position.

Figure 3. Figure 4.

LCD Screen:

Call Tone

Melody

TX icon, light on in Transmission mode

Antenna icon, light on in Receiving mode

Rx icon, Light on in Receiving mode

Dual Watch icon, Displayed during Dual Watch mode.

Battery level indicators. Displays current Battery level.

Baby icon, light on in Babysitter unit selection menu

and Standby mode when the System is set to become

a Babysitter unit.

Monitor icon, light on in Parent-monitor unit selection

menu and Standby mode when the System is set to

become a Parent-monitor unit.

Main Channels, Channel number changes from 1 to 8

as selected by user.

SCAN icon, light on in Channel scanning mode.

Stop watch icon, light on in stop watch mode.

CTCSS code. Sub Channel Number changes from 1 to

38 selected by user.

Music icon, Light on in Call Tone Melody selection menu.

Key lock icon, light on when buttons are locked.

Auto-Power-Off icon, light on in APO selection menu

and Standby mode when APO timer is enabled.

VOX icon, light on in VOX selection menu and Standby

mode when VOX function is enabled.

Numerical digits

Scrambler icon, light on in Scrambler selection menu

and Standby mode when the Scrambler function is

enabled.

Baby Monitor

Battery level

Indicator Numerical

digits

Channel Scan Selection

Parent Monitor

Dual Watch VOX icon

Stop Watch

RX Icon

Key Lock

Auto Power Oﬀ

Sub Channel Number

Main Channel

Number

Scrambler

Antenna icon

TX Icon

NOTE: SQ icon & ALC icon only briefly display on LCD screen once turn

ON the unit in SELF-TEST mode.

The COMMUNICATOR has a built in POWER SAVER feature for

maximum battery life. But when the COMMUNICATOR is not being

used, conserve battery power by pressing the button to OFF.

Remove the batteries if the unit will not be used for a long period

of time.

Turning the Unit ON:

Press and hold the button. The unit will "beep" with dual tone and the

LCD SCREEN will brieﬂy display a SELF-TEST Screen.

Turning the Unit OFF:

Press and hold the button. The unit will "beep" with a signal tone and

the LCD Screen will turn blank.

Setting Auto Power Oﬀ Timer

1. Press button 9 times to enter Auto Power Off timer selecting page.

2. Press / button to set the desired Timer (0, 1, 2, 3, 6 hours). Press PTT

or button to conﬁrm.

3. The PMR will automatically power off when the timer is time out.

Adjusting Speaker Volume:

1. Press the Up button to increase the Speaker Volume.

2. Press the Down button to decrease the Speaker Volume.

3. The Speaker Volume level is indicated by the numbers (1 to 8 level), displayed

in the lower right corner of the LCD Screen.

NOTE: Volume Up and Down buttons are disabled during BUTTON LOCK

mode

Receiving & Transmitting Radio Signal

Receiving a Signal:

The unit is continuously in the RECEIVE mode when the unit is ON and not

Transmitting. When you receive a signal on the current channel, the LED

illuminates GREEN and the RX icon and the Antenna icon are displayed.

NOTE: 1.The System is continuously in the receiving mode for 6 seconds after

Power On and if no any key pressing.

2. After 6 seconds for the last key pressing, the System enters to the

power saving mode.

3. When a radio signal matches with the existing channel and sub-code

setting, the speaker will be turned on.

4. If a radio signal matches with the existing channel only but the sub-

code is wrong, the speaker will be muted.

5. In order for other people to receive your transmission, they must also

be on the same channel you are currently using. Refer to the "Channel

Selection" section for more information.

Transmitting a Signal:

1. Press and hold the button to TRANSMIT. The TX LED Indicator will light PTT

up in red and the TX icon is displayed. Hold the unit in a vertical position with

the MICROPHONE 2 to 3 inches from the mouth. While holding the PTT

button, speak into the unit using a normal tone of voice.

2. PTTRelease the button when you have finished transmitting.

NOTE: Check the channel activity by pressing and holding the MONITOR M

button. You'll hear static if the channel is unoccupied. Don't TRANSMIT

if someone is talking on the channel.

Channel Selection

8 basic channels and 38 sub channels are available.

Changing Basic Channels

1. Press the MENU button once to enter BASIC CHANNEL SELECTION

mode. The current channel number flashes on the LCD Screen.

2. While the channel number is flashing:

Press the Up button to move to a higher channel.

Press the Down button to move to a lower channel.

The channel changes from 1 to 8, or from 8 to 1.

3. PTT Press the ENTER button or button to confirm the selected channel

and return to the NORMAL mode.

Changing CTCSS Code - Subchannels

The COMMUNICATOR has 38 available CTCSS subchannels. The sub-codes

(CTCSS) help minimize interference by providing you with a choice of

code combinations.

To set the CTCSS code:

1. Press the MENU button twice until the CTCSS digits ﬂash.

2. While the CTCSS code digits are flashing:

Press the Up button to move to a higher subchannel.

Press the Down button to move to a lower subchannel.

The subchannel changes from 00 to 38, or from 38 to 00.

3. Press the ENTER button or button to confirm your selection and PTT

return to the NORMAL mode.

NOTE: 1.To communicate with other PMR units, both units must be

switched to the same channel and CTCSS subchannel.

2. Channel change operations are disabled during BUTTON LOCK

mode.

3. Refer to the "Channel Table" section of this Owner's Manual

for detailed frequency listings.

Selecting Call Tone melodies

1. Press the MENU button 4 times to enter Call tone melodies selecting

page.

2. Press / button. The Call Tone melody number will be changed ascending

or descending in one step (1-10). 10 songs can be selected.

3. PTTPress or button to conﬁrm your selection.

Monitoring Radio Signal:

You can use the MONITOR feature to check for weak signals in the current

channel for 15 seconds.

1. Press the MONITOR button once to activate this function. M

2. Rx icon will display on the LCD Screen while this function is activated.

3. Press again the MONITOR button to deactivate the function.M

ENTER / LCD Back-light / Button Lock:

1. Press and immediately release the ENTER button to light up the LCD

Screen. The BACKLIGHT will automatically shut off after 4 seconds if no

other buttons have been pressed.

2. Press and hold the ENTER button until the BUTTON LOCK icon is

displayed on the LCD Screen.

NOTE:  Volume and Channel Change Operations are disabled during

BUTTON LOCK mode. Press and hold the ENTER button again

to deactivate BUTTON LOCK mode.

Sending Call Tones

You can use CALL TONES to alert the other when you are attempting to

contact them. You can also use CALL TONES to signal the beginning or

the end of a transmission.

1. Press the CALL button, the red TX LED indicator will light up and the C

CALL TONE continues for 2 seconds.

2. Release the CALL button, your CALL TONES will transmit to nearby C

receivers set to the same channel.

Selecting Scrambler mode

1. Press menu 3 times to enter to Scrambler selecting page.

2. While Scrambler icon is displayed, and the "OF" icon or digit is flashing, press

/ button to select the desired scambler mode (off, 1, 2, 3, 4)

3. Press ENTER or PTT button to confirm.

4. Both of the Transmission and Receiving units must be set into the same

Scrambler mode or disable Scrambler function.

NOTE: Scrambler feature adds an extra layer of privacy but does not

guarantee full secrecy.

Channel Scan:

CHANNEL SCAN performs searches for active signals in an endless loop

from basic channel 1 to 8.

1.  Press SCAN button to activate CHANNEL SCAN. The channel number SC

on the LCD Screen changes rapidly until an active signal is detected.

 During CHANNEL SCAN mode.

Press ENTER button to confirm the selected channel.

Press the CALL button to change to CALL function and to send a C

CALL TONE on that active channel.

Press the SCAN button again to deactivate CHANNEL SCAN mode.SC

2.  When an active signal (one of 8 channels) is detected. CHANNEL SCAN

pauses, keeping the active signal broadcasted.

3. Press the button to communicate through the active signal channel and PTT

CHANNEL SCAN is deactivated.

4.  When an active signal (one of 8 channels) is detected, but another channel

is desired, press the Up or Down button to bypass the current channel

and continue to search for another active channel.

Dual Watch:

You can use Dual Watch to monitor 2 channels.

To enter Dual Watch mode:

1. Press MENU button 7 times.

2. Press Up and Down buttons to select desired channel.

3. Once Dual Watch is on, automatically scan the channel that between 2

2 prefixed channel and the carrier stop on either activated channel

to receive. Dual Watch restarts when the carrier disppears.

4. Press MONITOR button to monitor weak signal.M

5. Press ENTER , or CALL button to end the Dual Watch mode.PTT C

Stop-Watch:

1. Press the MENU button 10 times to enter Stop-watch page.

2. Press the Up button once, the Stop-watch will start to count.

3. Press the Down button once to hold the Stop-watch. Press Down button

again to reset the counter.

COMMUNICATOR MODEL 103

NOTE: The maximum transmission range will vary depending on terrain

and environment.

Speciﬁcations:

CTCSS ( Continuous Tone Coded Squelch System) Frequency Table.

Channels Available 8 Channels

CTCSS Sub-channel 38 for each Channel

Output Power (TX) 0.5W

Battery Life 30 Hours (typical)

Range About 3 Miles

CHANNEL TABLE

446.00625

446.01875

446.03125

446.04375

CHANNEL FREQUENCY (MHz) CHANNEL FREQUENCY (MHz)

446.05625

446.06875

446.08125

446.09375

SYMPTOM

No power.

Reception is

weak.

Cannot

change

channels.

Range is

limited.

Sound

distortion

problems.

SOLUTION

=Check batteries. Ensure that the batteries are installed

properly.

= The batteries may be weak.

= Replace old batteries with three (3) new "AAA"

alkaline batteries or 3.6V "AAA" Ni-MH rechargeable

battery pack .

= Press the Up button to increase VOLUME.

= The receiving signal may be weak and/or out of range.

= If this happens, press the MONITOR button.M

= To change channels, press the MENU button until

the channel number ﬂashes on the LCD Screen.

= Press the Up or Down buttons to change channels.

= Batteries may be weak.

= BUTTON LOCK must be deactivated.

= BATTERIES may be weak.

= Replace with new batteries if the BATTERY LEVEL

indicator is low.

= The maximum range will vary depending on terrain and

environment.

= Open fields provide the maximum range, while steel/concrete

structures, heavy foliage and use in buildings and in

vehicles may limit the range significantly.

= Wearing the radio close to the body, such as in a pocket

or on a belt, will decrease range; change the location of

the radio.

= If you are transmitting, speak in a normal tone of voice,

2 to 3 inches away from the MICROPHONE.

= If you are receiving, lower the volume to a comfortable

level.

= Radios too close. Radios must be at least 5 feet apart;

increase your distance.

= Radios too far apart. Obstacles interfere with transmission.

Talk range is up to 3 miles in clear unobstructed

conditions.

Troubleshooting

WARNING: Using batteries

1.  The PMR units operate with 3 1.5V AAA/LR03 regular Alkaline

or Ni-MH (nickel metal hydride) batteries.

2.  Batteries and rechargeable battery packs should not be

thrown with domestic rubbish. You may hand them in at

your nearest collection point.

3.  Do not leave batteries installed over a long period of time

as leakage may occur and this can destroy the radio.

COMMUNICATOR MODEL 103

Produktspecifikationer

Varumärke:	Hoffer
Kategori:	Walkie-talkies
Modell:	103

Behöver du hjälp?

Om du behöver hjälp med Hoffer 103 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Walkie-talkies Hoffer Manualer

Hoffer 103 Bruksanvisning

12 September 2024

Walkie-talkies Manualer

Nyaste Walkie-talkies Manualer

Audioline Slim PMR 31 Bruksanvisning

17 Oktober 2024

Midland LXT490 Bruksanvisning

14 Oktober 2024

Audioline PMR 46 Bruksanvisning

14 Oktober 2024

Silvercrest SPMR 8000 A1 Bruksanvisning

13 Oktober 2024

Nedis WLTK0800BK Bruksanvisning

11 Oktober 2024

Denver WTA-448 Bruksanvisning

5 Oktober 2024

GoGEN BOB VYSILACKY Bruksanvisning

30 September 2024

Cobra MicroTalk CXT545 Bruksanvisning

27 September 2024

Motorola Mag One BPR40 Bruksanvisning

26 September 2024

Baofeng UV-82 Bruksanvisning

25 September 2024