Honeywell CWIREADPTR4001/U Bruksanvisning

Honeywell Inte kategoriserad CWIREADPTR4001/U

Läs nedan 📖 manual på svenska för Honeywell CWIREADPTR4001/U (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

C2 R K Y

HVAC

BEFORE

Thermostat

Installation Guide

resideo.com

C WIRE ADAPTER

Online Guides and Support

OFF

Turn the power off at the

breaker box or control

switch for your HVAC*

system.

Remove your old thermostat

from the wall plate.

*Heating, ventilation, and air conditioning

Overview

This product provides a C wire (common wire) to power a

thermostat. Only install if you do not have a C wire available to

connect to your thermostat.

5Open HVAC system’s cover

to reveal the control board.

6Take a picture of the wires

on the control board.

Ensure the terminal labels

and wires are in the image.

You may need to reference

the picture later.

* O or B terminal may also be used.

CONTINUE

7Use the provided stickers to

label the following

connected wires:

8Disconnect ONLY the wires

that you just labelled:

AFTER

HVAC

C Wire

AdapterThermostat

OFF

Breaker box Switch

Do not remove any wires

at this time!

ZONING CONTROL PANEL CHECK

For zoned systems, install the C Wire Adapter

between the thermostat and the zoning panel, NOT

between the zoning panel and HVAC equipment.

3Take a picture of the wiring.

Ensure the terminal labels

and wires are in the image.

You may need to reference

the picture later.

Conﬁrm that you do not have

a wire in the C terminal. If

you have a wire in the

C terminal, then you do not

need this product.

Look for an unused wire. If

you have an unused wire,

then you do not need this

product. Connect one end of

that wire to C terminal at the

HVAC and the other to C

terminal at new thermostat.

* The C wire (common) might be

labeled as B rather than C on certain

thermostats.

Go to your HVAC system. It may be located in your

attic, crawl space or basement.

C terminal *

EXAMPLE

W W1or

Y Y1or

R or Rc

CW W2G R K Y

Terminal Labels

Wires

R Rcor

•

EXAMPLE

Y Y1or

R or Rc

W W1or

Y Y1or

•

* Not all systems will have a

W or W1-wire. On a heat pump

application, the wire coming from

O/B on the old thermostat would

match to either O or B at equipment

rather than W.

** If multiple wires are connected

to a terminal, only label the the wire

running to your thermostat.

R Rcor

•

W W1or

Y Y1or

•

* Do NOT disconnect wires that you

did not label.

** If multiple wires are connected

to a terminal, only remove the the

wire running to your thermostat.

*** On a heat pump application,

the wire coming from O/B on the old

thermostat would match to either O

or B at equipment rather than W.

***

33-00342-08

Before mounting, check to

make sure surface is clean

enough to ensure good

adhesion.

Mount C Wire Adapter

inside the furnace using

included mount and

adhesive pad.

11 Connect the wires from

the “Equipment”

labelled side of the C

Wire Adapter to the

matching terminals on

the control board.

* If there are separate wires to

W and O, leave the W and O wires

attached at HVAC and do not

connect them to the C Wire

Adapter.

Label your now converted

wires as shown.

Close the HVAC system’s cover.

Leave the power off.

12 CHECKPOINT

Your C Wire Adapater should now be installed between

your thermostat wiring and the control board.

HVAC

Control Board

Thermostat

C Wire

Adapter

Adhesive pad

Mount

G Y

Wires

Labels

Label ALL of the remaining

wires according to their

terminals.

* O/B terminal may also be used.

G YW R

EXAMPLE

17 Conﬁrm you have labelled

ALL of your wiring.

Disconnect the wires from

the old wall plate.

* O/B terminal may also be used.

9Insert the wires you just

disconnected into the

C Wire Adapter terminals.

W RC K

THERMOSTAT

EQUIPMENT

W or O/B

Wires

W or O/B

Terminals

This will convert the G and

Y-wires into C and K-wires.

10 Take a picture of the wires

you inserted into the C Wire

Adapter.

Ensure the terminal labels

and wires are in the image.

You may need to reference

the picture later.

STAT

EQU

W C K R

THERMOSTAT

EQUIPMENT

EXAMPLE

Refer to your new thermostat’s

installation guide for detailed

instructions to complete the

following tasks below.

The wires you label C and K are

the wires you inserted into the

C and K-terminals in step .9

NEXT STEPS

W W1 O B, , , or *

Y Y1or

EXAMPLE Go back to your thermostat.

ARemove the old wall plate and mount the new one.

CComplete your new thermostat’s installation by

attaching the thermostat to the wall plate,

restoring the power, and conﬁguring the

thermostat.

BWire the new thermostat.

EXAMPLE

C W

Refer to the labels you

applied when inserting

the wires.

When done wiring, you should

have wires in the C and

K-terminals.

You should not have wires in

the Y or G-terminals.

Resideo Technologies, Inc.

1985 Douglas Drive North, Golden Valley, MN 55422

1-800-468-1502

33-00342—08 M.S. Rev. 05-20 | Printed in United States

The Honeywell Home trademark is used under license from Honeywell International, Inc.

This product is manufactured by Resideo Technologies, Inc. and its afﬁliates.

www.resideo.com

Produktspecifikationer

Varumärke:	Honeywell
Kategori:	Inte kategoriserad
Modell:	CWIREADPTR4001/U
Färg på produkten:	Aluminium, Black
Mobila operativsystem som stöds:	Android, iOS
LED-indikatorer:	Ja
Bluetooth-version:	3.0+HS
Anslutningsteknik:	Draadloos
Typ av strömkälla:	Batterij/Accu
fingeravtrycksläsare:	Nee
Snabbstartsguide:	Ja
Antal batterier/batterier som stöds:	2
Material:	Aluminium
Avsedd för:	Universeel
Stöder Windows:	Ja
Rekommenderad användning:	Universeel
Bakgrundsbelysning:	Nee
Förbindelse:	Bluetooth
USB-hubb:	Nee
Numerisk knappsats:	Ja
Stöder Mac-operativsystem:	Ja
Inkluderar mus:	Nee
Pekdon:	Nee
Tangentbord i full storlek:	Ja
Handledsstöd:	Nee
Tangentbordsstorlek:	Volledige grootte (100%)
Stil tangentbord:	Recht
Batterier-ingår:	Ja
Batterityp:	AAA