Hooker 5198-30310 Bruksanvisning
Hooker
Kontorsstol
5198-30310
Läs nedan 📖 manual på svenska för Hooker 5198-30310 (2 sidor) i kategorin Kontorsstol. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/2
1/2
ASSEMBLY INSTRUCTION
Item#:5198-30310 desk chair (one per carton)
** Please make sure you have all parts indicated below prior to assembly.
Assembly Steps:
1. Place back frame (E) on a clean surface.
2. Tighten seat frame(F) to back legs of frame(E) by using bolt(G), lock washer(B) and flat washer(A)
at the center location (see diagram 2). Using bolts (C), lock washers (B) and flat washers (A),
tighten the corners of seat frame (F) to back legs of frame (E). (See diagram 1)
3. Install front legs (H) onto seat frame (F) using bolts (G), lock washers (B) and flat washers (A).
Tighten all bolts by hand. (See diagram 2)
4. After all bolts are attached and hand tightened, turn the chair upright.
5. Level the chair following the “chair leveling instruction” as below.
6. Make sure the chair is level and then tighten all bolts completely by using the allen wrench (D).
DIAGRAM 1
DIAGRAM 2
2/2
PLEASE READ THESE INSTRUCTIONS PRIOR TO ASSEMBLING THE
CHAIRS
CHAIR LEVELING INSTRUCTION SUPPLEMENT
Chair leveling procedures:
To make the assembly process easy and efficient, please read the entire instruction sheet prior to
assembling of the chair. Make sure all hardware listed is included. To properly assemble the chair, none of
the bolts should be fully tightened until all components are attached to the chair. This will allow an
opportunity to level the chair and prevent any unnecessary “rocking”.
1. Place the loosely assembled chair on a hard flat surface.
2. Apply gentle downward pressure on the seat. This step eliminates rocking and ensures the chair to
be level.
3. Once the chair is level, tighten all bolts and nuts.
Note:
Most floors have slight irregularities that can affect chair leveling. If your chair is uneven when placed
in its desired location, perform the following steps:
1. Loosen front legs to finger tight.
2. Extend both front legs upward to their fullest length.
3. Gently push downward on the front edge of the seat until all four legs rest on the floor.
4. Re-tighten all bolts and nuts.
Cleaning Instruction: Clean finished parts with a damp cloth using a mild dishwashing liquid and water solution.
Polish the finish with soft cloth and an industry recognized furniture polish.
Produktspecifikationer
| Varumärke: | Hooker |
| Kategori: | Kontorsstol |
| Modell: | 5198-30310 |
Behöver du hjälp?
Om du behöver hjälp med Hooker 5198-30310 ställ en fråga nedan och andra användare kommer att svara dig
Kontorsstol Hooker Manualer
18 September 2024
18 September 2024
18 September 2024
18 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
Kontorsstol Manualer
- Kontorsstol IKEA
- Kontorsstol Aeris
- Kontorsstol Jysk
- Kontorsstol Gembird
- Kontorsstol Bush
- Kontorsstol Sharkoon
- Kontorsstol Thermaltake
- Kontorsstol Trust
- Kontorsstol Techly
- Kontorsstol BDI
- Kontorsstol Sandberg
- Kontorsstol Boss
- Kontorsstol Antares
- Kontorsstol Habitat
- Kontorsstol Speed-Link
- Kontorsstol Haworth
- Kontorsstol Sedus
- Kontorsstol Stem
- Kontorsstol Drift
- Kontorsstol Interstuhl
- Kontorsstol Alpha Gamer
- Kontorsstol Logilink
- Kontorsstol Gispen
- Kontorsstol Safco
- Kontorsstol Schaffenburg
- Kontorsstol HJH Office
- Kontorsstol X Rocker
- Kontorsstol SilentiumPC
- Kontorsstol Kenson
- Kontorsstol Humanscale
- Kontorsstol TOGU
- Kontorsstol HermanMiller
- Kontorsstol MooreCo
Nyaste Kontorsstol Manualer
26 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
24 September 2024
24 September 2024
24 September 2024