Hotpoint CD67G0C2CA/UK Bruksanvisning

Hotpoint Ugn CD67G0C2CA/UK

Läs nedan 📖 manual på svenska för Hotpoint CD67G0C2CA/UK (8 sidor) i kategorin Ugn. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/8
CD67G0CCX/UK
CD67G0C2CJ/UK
CD67G0C2CA/UK
ADAPTING TO DIFFERENT TYPES OF GAS
(This operation needs to be carried out by a
qualified technician.)
In order to adapt the appliance to a type of gas
other than the type for which it was manufactured
(indicated ontherating label), follow thededicated
steps provided after installation drawings.
ELECTRICAL WARNINGS
IMPORTANT: Information about current and
voltage consumption is provided on the rating
plate.
The rating plate is on the front edge of the
oven (visible when the door is open).
It must be possible to disconnect the appliance
from the power supply by unplugging it if
plug is accessible, or by a multi-pole switch
installed upstream of the socket in accordance
with the wiring rules and the appliance must
be earthed in conformity with national electrical
safety standards.
The power cable must be long enough to connect the appliance,
once fitted in its housing, to the main power supply. Do not pull the
power supply cable.
Do not use extension leads, multiple sockets
or adapters. The electrical components must not
be accessible to the user after installation. Do not
use the appliance when you are wet or barefoot.
Do not operate this appliance if it has a damaged
power cable or plug, if it is not working properly,
or if it has been damaged or dropped.
If the supply cord is damaged, it must
be replaced with an identical one by the
manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard -
risk of electric shock.
If the power cable needs to be replaced,
contact an authorised service centre.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
switched off and disconnected from the power
supply before performing any maintenance
operation; never use steam cleaning equipment -
risk of electric shock.
Do not use harsh abrasive cleaners or metal
scrapers to clean the door glass since they can
scratch the surface, which may result in shattering
of the glass.
Do not use abrasive or corrosive products,
chlorine-based cleaners or pan scourers.
Make sure the appliance has cooled down
before cleaning or performing maintenance. - risk
of burns.
WARNING: Switch off the appliance before
replacing the lamp - risk of electric shock.
To avoid damaging the electric ignition device, do not use it when
the burners are not in their housing.
Wear protective gloves for cleaning and
maintenance.
DISPOSAL OF PACKAGING MATERIALS
ENERGY SAVING TIPS
Only preheat the oven if specified in the cooking table
dark lacquered or enamelled baking trays as they
to save even more energy and time.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance meets: Ecodesign requirements of European
Regulation 66/2014; Energy Labelling Regulation 65/2014;
Products and Energy Information (Amendment) (EU Exit)
Regulations (2019), in compliance with the European standard:
EN 15181. This appliance meets Ecodesign requirements
Energy-Related Products and Energy Information
(Amendment) (EU Exit) Regulations 2019 in compliance
with the European standard EN 30-2-1.
DECLARATION OF CONFORMITY
Ecodesign for Energy-Related
of European Regulation 66/2014 and the Ecodesign for
The packaging material is 100 % recyclable
and is marked with the recycle symbol .
The various parts of the packaging must therefore
be disposed of responsibly and in full compliance
with local authority regulations governing
waste disposal .
This appliance is manufactured with recyclable or
reusable materials. Dispose of it in accordance
with local waste disposal regulations . For further information
contact your local authority, the collection service for household
waste or the store where you purchased the appliance.
This appliance is marked in compliance with
The European Directive 2012/19/EU, Waste Electrical and
Electronic Equipment ( WEEE ) and with the
Waste Electrical and Electronic Equipment regulations 2013
( as amended ) . By ensuring this product is disposed
of correctly , you will help prevent negative consequences
for the environment and human health . The ed , symbol
on the product or on the accompanying documentation
indicates that it should not be treated as domestic
waste but must be taken to an appropriate
collection centre for the recycling of electrical and
electronic equipment.
on the treatment, recovery and recycling of household
household electrical appliances,
or your recipe. Use dark lacquered or enamelled
absorb heat better. Use a pressure cooker
6
V
V
Z
• Pry the fixing tab “V” and remove the oven burner
• Unscrew the oven burner nozzle using the socket
spanner for the nozzles “Z”“Z”
“Z”“Z”“Z”, or a 7 mm socket
spanner, and replace it with a nozzle suited to the
new type of gas (see Table 1).
Take particular care handling the spark plug
wires and the thermocouple pipes.
• Replace all the parts, following the steps
described above in the reverse order.
b )b )
b )b )
b ) Minimum regulation of the main and top gas
oven burner with thermostat:
• light the burner as described in the
paragraph the oven knob” of the
instruction booklet.
• turn the knob to MaxMax
MaxMaxMax for about 10 minutes
and then turn the knob to the MinMin
MinMin
Min
setting;
• remove the knob;
• regulate the screw positioned outside the
thermostat pin until the flame is
small but steady.
! !
! ! In the case of liquid gas, the regulation screw
must be screwed in to the bottom.
• check that the burner does not turn off whenwhen
you turn the knob from Max to Min and and
when you open and close the oven door quickly.
Adapting the gas grill to different types of gas
Replacing the nozzle of the grill burner:
On completion of the operation, replace the old
rating sticker with one indicating the new type of gas
used. This sticker is available from our Service
Centres.
No t eNo t e
No t eNo t eNo t e
Should the pressure of the gas used be different (or
vary) from the recommended pressure, it is
necessary to fit a suitable pressure regulator onto
the inlet pipe in compliance with current National
Regulations relative to “regulators for channelled
gas”.
If the appliance is connected to a liquid gas supply, the
bypass screw must be set to a minimum.
While the burner is alight, quickly change the position of the
knob from minimum to maximum and vice versa several times,
checking that the flame is not extinguished.
Upon completion of adjustment, reseal using sealing
wax or an equivalent material.
1. Remove the enamelled baffle at the front of the grill
(2 screws).
2. Remove the screw on the right hand side of the
burner and gently slide the burner off the injector.
3. Using a 7mm socket, replace the grill injector as
appropriate (see table on previous page).
4. Re-assemble the burner and baffle.
Adapting to different types of gas (main and top
oven)
In order to adapt the oven to a different type of gas
with respect to the gas for which it was
manufactured (indicated on the label), follow these
simple steps:
a)a)a)a)a) Replacing the oven burner nozzle
•open the oven door fully
•pull out the sliding oven bottom
unscrew the two screws and take o the shield
protecting the burner (in main oven burner only).
V
V
Z
• Pry the fixing tab “V” and remove the oven burner
• Unscrew the oven burner nozzle using the socket
spanner for the nozzles “Z”“Z”
“Z”“Z”“Z”, or a 7 mm socket
spanner, and replace it with a nozzle suited to the
new type of gas (see Table 1).
Take particular care handling the spark plug
wires and the thermocouple pipes.
• Replace all the parts, following the steps
described above in the reverse order.
b )b )
b )b )
b ) Minimum regulation of the main and top gas
oven burner with thermostat:
• light the burner as described in the
paragraph the oven knob” of the
instruction booklet.
• turn the knob to MaxMax
MaxMaxMax for about 10 minutes
and then turn the knob to the MinMin
MinMin
Min
setting;
• remove the knob;
• regulate the screw positioned outside the
thermostat pin until the flame is
small but steady.
! !
! ! In the case of liquid gas, the regulation screw
must be screwed in to the bottom.
• check that the burner does not turn off whenwhen
you turn the knob from Max to Min and and
when you open and close the oven door quickly.
Adapting the gas grill to different types of gas
Replacing the nozzle of the grill burner:
On completion of the operation, replace the old
rating sticker with one indicating the new type of gas
used. This sticker is available from our Service
Centres.
No t eNo t e
No t eNo t eNo t e
Should the pressure of the gas used be different (or
vary) from the recommended pressure, it is
necessary to fit a suitable pressure regulator onto
the inlet pipe in compliance with current National
Regulations relative to “regulators for channelled
gas”.
If the appliance is connected to a liquid gas supply, the
bypass screw must be set to a minimum.
While the burner is alight, quickly change the position of the
knob from minimum to maximum and vice versa several times,
checking that the flame is not extinguished.
Upon completion of adjustment, reseal using sealing
wax or an equivalent material.
1. Remove the enamelled baffle at the front of the grill
(2 screws).
2. Remove the screw on the right hand side of the
burner and gently slide the burner off the injector.
3. Using a 7mm socket, replace the grill injector as
appropriate (see table on previous page).
4. Re-assemble the burner and baffle.
Adapting to different types of gas (main and top
oven)
In order to adapt the oven to a different type of gas
with respect to the gas for which it was
manufactured (indicated on the label), follow these
simple steps:
a)a)a)a)a) Replacing the oven burner nozzle
•open the oven door fully
•pull out the sliding oven bottom
unscrew the two screws and take o the shield
protecting the burner (in main oven burner only).
INSTALLATION TIPSINSTALLATION TIPS
EN
WARNING : This operation must be perfomed
by a qualified technician
10

Produktspecifikationer

Varumärke: Hotpoint
Kategori: Ugn
Modell: CD67G0C2CA/UK

Behöver du hjälp?

Om du behöver hjälp med Hotpoint CD67G0C2CA/UK ställ en fråga nedan och andra användare kommer att svara dig


Ugn Hotpoint Manualer

Hotpoint

Hotpoint HS68M8PCX Bruksanvisning

5 Januari 2025
Hotpoint

Hotpoint HB 0577B NE Bruksanvisning

31 December 2025
Hotpoint

Hotpoint H6GG1F (X) IT Bruksanvisning

31 December 2025
Hotpoint

Hotpoint FA4S 844 P IX HA Bruksanvisning

31 December 2025
Hotpoint

Hotpoint H6TMH2AF (X) IT Bruksanvisning

31 December 2025
Hotpoint

Hotpoint FIT 804 H AV HA Bruksanvisning

15 December 2024
Hotpoint

Hotpoint PCN 640 T (AN) R /HA Bruksanvisning

15 December 2024
Hotpoint

Hotpoint FIT 834 AN HA Bruksanvisning

15 December 2024
Hotpoint

Hotpoint PCN 750 T (OW) R /HA Bruksanvisning

15 December 2024
Hotpoint

Hotpoint FA4S 544 IX HA Bruksanvisning

15 December 2024

Ugn Manualer

Nyaste Ugn Manualer

CDA

CDA VK905 Bruksanvisning

25 Mars 2025
Whirlpool

Whirlpool WOI4S8HM1SXA Bruksanvisning

25 Mars 2025
AEG

AEG NBU5A20SB Bruksanvisning

24 Mars 2025
AEG

AEG NBU5P40BCK Bruksanvisning

24 Mars 2025
AEG

AEG TA5PB53WAB Bruksanvisning

24 Mars 2025
AEG

AEG OU5AE20AK Bruksanvisning

24 Mars 2025
AEG

AEG TU5AB20SCK Bruksanvisning

24 Mars 2025
AEG

AEG TB8SB631AB Bruksanvisning

24 Mars 2025
AEG

AEG TU5PB40NCK Bruksanvisning

24 Mars 2025
AEG

AEG TU5PB40NSK Bruksanvisning

24 Mars 2025