Hotpoint HDM67G0CCW/UK Bruksanvisning

Hotpoint Ugn HDM67G0CCW/UK

Läs nedan 📖 manual på svenska för Hotpoint HDM67G0CCW/UK (23 sidor) i kategorin Ugn. Denna guide var användbar för 13 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/23
HDM67G0CCW/UKHDM67G0CCW/UKHDM67G0CCW/UK
EN ENGLISH
Health and Safety guide
Installation guide
Quick guide
2
3
EN
SAFETY INSTRUCTIONS
IMPORTANT TO BE READ AND OBSERVED
CAUTION : Use of the gas cooking appliance
results in the production of heat, moisture and
products of combustion in the room in which
it is installed. Ensure that the kitchen is well
ventilated, especially when the appliance is in
use: keep natural ventilation holes open or
install a mechanical ventilation device (mechanical
extractor hood). Prolonged intensive use of the
appliance may call for additional ventilation, such
as opening awindow, ormore effectiveventilation,
for example increasing the level of mechanical
ventilation (if possible).
Failure to follow the information in this manual exactly may cause a
fire or explosion, resulting in property damage or personal injury.
Before using the appliance, read these safety
instructions. Keep them nearby for future
reference.
These instructions and the appliance itself provide
important safety warnings, to be observed at all
times. The manufacturer declines any liability for
failure to observe these safety instructions, for
inappropriate use of the appliance or incorrect
setting of controls.
WARNING: The appliance and its accessible
parts become hot during use. Care should
to avoid touching heating elements. Children less
than 8 years of age must be kept away unless
continuously supervised.
WARNING : Danger of fire : Do not store items
on the cooking surfaces.
CAUTION : The cooking process has to be
supervised. A short cooking process has to be
supervised continuously.
WARNING: Leaving the hob unattended when
cooking with fat or oil can be dangerous risk of–
fire. NEVER try to extinguish a fire with water, but
switch off the appliance and then cover the flames
e.g. with a lid or a fire blanket.
Do not use the hob as a work surface or support.
Keep clothes or other flammable materials away
from the appliance, unitl all the components have
cooled down completely - risk of fire.
Very young children (0-3 years) should be kept
away from the appliance. Young children (3-8
years) should be kept away from the appliance
unless continuously supervised. Children from 8
years old and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge can use this appliance
only if they are supervised or have been given
instructions on safe use and understand the
hazards involved. Children must not play with the
appliance. Cleaning and user maintenance must
not becarried out by children withoutsupervision.
CAUTION : In case of hotplate glass breakage:-
shut immediately off all burners and any electrical
heating element and isolate the appliance from
the power supply; - do not touch the appliance
surface; -do not use the appliance
The glass lid can break
Turn off all
Do not shut
WARNING: The appliance and its accessible
parts become hot duringuse. Care should be taken
to avoid touching heating elements. Children less
than 8 years of age must be kept away unless
continuously supervised.
Never leave the appliance unattended during
use.
Keep clothes or other flammable materials
away from the appliance, until all the components
have cooled down completely - risk of fire. Always
be vigilant when cooking foods rich in fat, oil or
when adding alcoholic beverages - risk of fire. Use
oven gloves to remove pans and accessories. At
the end of cooking, open the door with caution,
allowing hot air or steam to escape gradually
before accessing the cavity - risk of burns. Do not
obstruct hot air vents at the front of the oven - risk
of fire.
Exercise caution when the oven door is in the
open or down position, to avoid hitting the door.
When you place the rack inside, make sure that
the stop is directed upwards and in the back of the
cavity.
and open the compartment door and/or
wait at least 1 min before attempting a further
ignition of the burner.
PERMITTED USE
CAUTION: The appliance is not intended to
be operated by means of an external switching
device, such as a timer, or separate remote
controlled system.
This appliance is intended to be used in
household and similar applications such as: staff
kitchen areas in shops, offices and other working
environments; farm houses; by clients in hotels,
be taken
if it is heated.
burners before closing the lid.
the lid when burners are lit.
The ignition device shall not be operated for
more than 15 seconds. If after 15 seconds
the burner has not lit, stop operating the device
motels, bed & breakfast and other residential
environments.
No other use is permitted (e.g. heating rooms).
This appliance is not for professional use. Do
not use the appliance outdoors.
Do not store explosive or flammable
substances (e.g. gasoline or aerosol cans) inside or
near the appliance - risk of fire.
Use pots and pans with bottoms the same
width as that of the burners or slightly larger (see
Improper use of the grids can result in damage
to the hob: do not position the grids upside down
or slide them across the hob.
Do not let the burner flame extend beyond the
edge of the pan
Do not use : Cast iron griddles, ollar stones,
terracotta pots and pans. Heat diffusers such as
metal mesh, or any other types. Two burners
simultaneously for one receptacle (e.g. Fish
kettle).
Should particular local conditions of the delivered
gas make the ignition of burner difficult, it is
advisable to repeat the operation with the knob
turned to small flame setting.
In case of installation of a hood above the cooktop,
please refer to the hood instructions for the correct
distance.
The protective rubber feet on the grids represent
a choking hazard for young children. After
removing the grids, please ensure that all the feet
are correctly fitted.
INSTALLATION
cuts.
The electrical and gas connections must
comply with local regulation.
Installation,
electrical connections and repairs must be carried
out by a qualified technician. Do not repair or
replace any partof the applianceunlessspecifically
stated in the user manual. Keepchildren away from
theinstallation site. After unpackingthe appliance,
make sure that it has not been damaged during
transport. In the event of problems, contact the
dealer or your nearest Aftersales Service. Once
installed, packaging waste (plastic, styrofoam
parts etc.) must be stored out of reach of
children - risk of suffocation. The appliance must
be disconnected from the power supply before
any installation operation - risk of electric shock.
During installation, make sure the appliance does
not damage the power cable - risk of fire or electric
shock. Only activate the appliance when the
installation has been completed.
This means LPG cylinders, whether partially or
completely full, must not be installed or stored
in rooms or storage areas that are below ground
level (cellars, etc.). It is advisable to keep only the
cylinder being used in the room, positioned so
that it is not subject to heat produced by external
sources (ovens, fireplaces, stoves, etc. ) which
could raise the temperature of the cylinder above
50 C.°
Should you find it difficult to turn the knobs for the burner, please
contact the After-sales Service, who can replace of the burner tap if
found to be faulty.
The openings use for the ventilation and dispersion of heat must never
be covered.
4
(in certain models only)
We recommend the appliance should be handled
and installed by two or more persons - risk of injury.
Use protective gloves to unpack and install - risk of
GAS CONNECTION
WARNING : Prior to installation, ensure that the
local distribution conditions (type of gas and gas
pressure) and the configuration of the appliance
are compatible.
Check that the pressure of the gas supply is
consistent with the values indicated in Table 1
(“Burner and nozzle specifications”).
WARNING : The configuration conditions of
this appliance are stated on the label (or data
plate).
WARNING : This appliance is not connected
to a combustion products evacuation device. It
must be installed and connected in accordance
with current installation regulations. Particular
attention must be paid to the relevant
requirements regarding ventilation.
If the appliance is connected to liquid gas,
the regulation screw must be
IMPORTANT : When the gas cylinder or gas
container is installed, it must be properly settled
(vertical orientation).
WARNING : This operation must be perfomed
by a qualified technician
adjusted to the
minimum setting.
The appliance should beconnected to the main
gas supply or to a gas cylinder in compliance with
the current national regulations. Before making
the connection, make sure that the appliance is
compatible with the gas supply you wish to use.
If it is not, follow the instructions indicated in the
paragraph "Adapting to different types of gas".
not protrude beyond the edge of the hob.
specific table). Make sure pots on the grates do
WARNING : Modification of the appliance and
its method of installation are essential in order to
use the appliance safely and correctly in all the
additional countries
Use pressure regulators suitable for the gas
pressure indicated in the instruction.
The room must be equipped with an air
extraction system that expels any combustion
fumes.
Liquid petroleum gas sinks to the floor as it
is heavier than air. Therefore, rooms containing
LPG cylinders must also be equipped with vents
to allow gas to escape in the event of a leak.
After connection to the gas supply, check for
leaks
minimum position 2* to check flame stability.
Connection to the gas network or the gas
cylinder may be carryout using a flexible rubber
or steel hose, in accordance with current national
legislation.
in accordance with IGEM/UP/1B. Light up the
burners and turn the knobs from max position 1* to
5
ADAPTING TO DIFFERENT TYPES OF GAS
(This operation needs to be carried out by a
qualified technician.)
In order to adapt the appliance to a type of gas
other than the type for which it was manufactured
(indicated onthe rating label), follow thededicated
steps provided after installation drawings.
ELECTRICAL WARNINGS
IMPORTANT: Information about current and
voltage consumption is provided on the rating
plate.
The rating plate is on the front edge of the
oven (visible when the door is open).
It must be possible to disconnect the appliance
from the power supply by unplugging it if
plug is accessible, or by a multi-pole switch
installed upstream of the socket in accordance
with the wiring rules and the appliance must
be earthed in conformity with national electrical
safety standards.
The power cable must be long enough to connect the appliance,
once fitted in its housing, to the main power supply. Do not pull the
power supply cable.
Do not use extension leads, multiple sockets
or adapters. The electrical components must not
be accessible to the user after installation. Do not
use the appliance when you are wet or barefoot.
Do not operate this appliance if it has a damaged
power cable or plug, if it is not working properly,
or if it has been damaged or dropped.
If the supply cord is damaged, it must
be replaced with an identical one by the
manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard -
risk of electric shock.
If the power cable needs to be replaced,
contact an authorised service centre.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
switched off and disconnected from the power
supply before performing any maintenance
operation; never use steam cleaning equipment -
risk of electric shock.
Do not use harsh abrasive cleaners or metal
scrapers to clean the door glass since they can
scratch the surface, which may result in shattering
of the glass.
Do not use abrasive or corrosive products,
chlorine-based cleaners or pan scourers.
Make sure the appliance has cooled down
before cleaning or performing maintenance. - risk
of burns.
WARNING: Switch off the appliance before
replacing the lamp - risk of electric shock.
To avoid damaging the electric ignition device, do not use it when
the burners are not in their housing.
Wear protective gloves for cleaning and
maintenance.
DISPOSAL OF PACKAGING MATERIALS
ENERGY SAVING TIPS
Only preheat the oven if specified in the cooking table
dark lacquered or enamelled baking trays as they
to save even more energy and time.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance meets: Ecodesign requirements of European
Regulation 66/2014; Energy Labelling Regulation 65/2014;
Products and Energy Information (Amendment) (EU Exit)
Regulations (2019), in compliance with the European standard:
EN 15181. This appliance meets Ecodesign requirements
Energy-Related Products and Energy Information
(Amendment) (EU Exit) Regulations 2019 in compliance
with the European standard EN 30-2-1.
DECLARATION OF CONFORMITY
Ecodesign for Energy-Related
of European Regulation 66/2014 and the Ecodesign for
The packaging material is 100 % recyclable
and is marked with the recycle symbol .
The various parts of the packaging must therefore
be disposed of responsibly and in full compliance
with local authority regulations governing
waste disposal .
This appliance is manufactured with recyclable or
reusable materials. Dispose of it in accordance
with local waste disposal regulations . For further information
contact your local authority, the collection service for household
waste or the store where you purchased the appliance.
This appliance is marked in compliance with
The European Directive 2012/19/EU, Waste Electrical and
Electronic Equipment ( WEEE ) and with the
Waste Electrical and Electronic Equipment regulations 2013
( as amended ) . By ensuring this product is disposed
of correctly , you will help prevent negative consequences
for the environment and human health . The ed , symbol
on the product or on the accompanying documentation
indicates that it should not be treated as domestic
waste but must be taken to an appropriate
collection centre for the recycling of electrical and
electronic equipment.
on the treatment, recovery and recycling of household
household electrical appliances,
or your recipe. Use dark lacquered or enamelled
absorb heat better. Use a pressure cooker
6
7
PRODUCT DESCRIPTION
CONTROL PANEL
EN
1.
Control panel
4. Runners for accessories
(the level is indicated on the wall
of the cooking compartment)
6.
Glass cover
1.
2.
2.
Main oven door
Removable Inner Door Glass
5.
5.
Gas burners
3.
3.
4.
6.
4.
Oven light
Timer
Electronic ignition
Left rear
hob burner Left front
hob burner
Thermostat
Top oven Main oven
Thermostat
Right front
hob burner
Right rear
hob burner
8
Before moving your cooker check that it is cool, and
switch off at the cooker control unit. Movement of
your cooker is most easily achieved by lifting the
front as follows:
Open the grill door sufficiently to allow a comfortable
grip on the underside front edge of the oven roof,
avoiding any grill elements. (FIG.A)
Take care in moving the cooker as it is heavy.
Take care to ensure that any floor covering is not
damaged.
Splashplate optional, apply to Parts Department
(see Back Cover for contact number.)
The following instructions should be read by a
qualified technician to ensure that the appliance is
installed, regulated and technically serviced
correctly in compliance with current regulations.
Positioning
Installation of the cooker
Moving the Cooker
Fig. A
Before moving your cooker check that it is cool, and
switch off at the cooker control unit. Movement of
your cooker is most easily achieved by lifting the
front as follows:
Open the grill door sufficiently to allow a comfortable
grip on the underside front edge of the oven roof,
avoiding any grill elements. (FIG.A)
Take care in moving the cooker as it is heavy.
Take care to ensure that any floor covering is not
damaged.
Splashplate optional, apply to Parts Department
(see Back Cover for contact number.)
The following instructions should be read by a
qualified technician to ensure that the appliance is
installed, regulated and technically serviced
correctly in compliance with current regulations.
Positioning
Installation of the cooker
Moving the Cooker
Fig. A
INSTALLATION TIPS
EN
WARNING : This operation must be perfomed
by a qualified technician
This unit may be installed and used only in
permanently ventilated rooms according to the British
The following
a. The cooker should not be installed in a bed sitting
room with a volume of less than 20m
3. If it is installed
in a room of volume less than 5m
3 an air vent of
effective area of 100cm
2 is required, if it is installed
in a room of volume between 5m
3 and 10m3 a
supplementary airvent area of 50cm2 is required,
if the volume exceeds 10m
3 no airvent is required.
However, if the room has a door or a window which
opens directly to the outside no air vent is required
even when the volume is between 5m
3 and 10m3.
b. During prolonged use of the appliance you may
consider it necessary to open a window to the
outside to improve ventilation.
c. If there are other fuel burning appliances in the
same room, B.S.5440 Part 2 Current Edition, should,
be consulted to determine the requisite air vent.
The room containing the appliance must contain
an openable window or an acceptable alternative
such as an adjustable louvre or hinged panel
opening direct to outside air.
This unit may be installed and used only in
permanently ventilated rooms according to the British
Standards Codes Of Practice: BS 5440 Part 2
requirements must be observed:
a. The cooker should not be installed in a bed sitting
room with a volume of less than 20m
3. If it is installed
in a room of volume less than 5m
3 an air vent of
effective area of 100cm
2 is required, if it is installed
in a room of volume between 5m
3 and 10m3 a
supplementary airvent area of 50cm2 is required,
if the volume exceeds 10m
3 no airvent is required.
However, if the room has a door or a window which
opens directly to the outside no air vent is required
even when the volume is between 5m
3 and 10m3.
b. During prolonged use of the appliance you may
consider it necessary to open a window to the
outside to improve ventilation.
c. If there are other fuel burning appliances in the
same room, B.S.5440 Part 2 Current Edition, should,
be consulted to determine the requisite air vent.
The room containing the appliance must contain
an openable window or an acceptable alternative
such as an adjustable louvre or hinged panel
opening direct to outside air.
For a correct installation of the cooker the following
precautions must be followed:
The height of the cooker can be adjusted by means
Adjust the feet by tilting the cooker from the side.
Then install the product into position.
NOTE: This appliance must not be fitted on a
platform.
The cooker is designed to fit between kitchen
cabinets spaced 600mm apart. The space either
side need only be sufficient to allow withdrawal of
the cooker for servicing. It can be used with
cabinets one side or both as well as in a corner
setting. It can also be used free-standing.
Adjacent side walls which project above hob level,
65mm and should be protected by heat
resistant material. Any overhanging surface or
cooker hood should not be nearer than 750mm.
a )a )
a )a )a ) The cooker may be located in a kitchen, a
kitchen/diner or bed sitting room, but not in a
bathroom or shower room.
b )b )
b )b )b ) The hoods must be installed according to
For a correct installation of the cooker the following
precautions must be followed:
The height of the cooker can be adjusted by means
of adjustable feet in the base of the product
Adjust the feet by tilting the cooker from the side.
Then install the product into position.
NOTE: This appliance must not be fitted on a
platform.
The cooker is designed to fit between kitchen
side need only be sufficient to allow withdrawal of
the cooker for servicing. It can be used with
cabinets one side or both as well as in a corner
setting. It can also be used free-standing.
Adjacent side walls which project above hob level,
must not be nearer to the cooker than
65mm and should be protected by heat
resistant material. Any overhanging surface or
cooker hood should not be nearer than 750mm.
a )a )
a )a )a ) The cooker may be located in a kitchen, a
kitchen/diner or bed sitting room, but not in a
bathroom or shower room.
b )b )
b )b )b ) The hoods must be installed according to
the requirements in the hood handbook (minimum
cabinets spaced 600mm apart. The space either
must not be nearer to the cooker than
750mm)
the requirements in the hood handbook (minimum
750mm)
dd
ddd ))
))) The cooker should be secured to the wall
dd
ddd ))
))
behind via a safety chain and hook. (fig.B)
) The cooker should be secured to the wall
c )c )c )c )c )c )c )c ) The wall behind the cooker, 50mm below and
450mm above, and the width of the cooker, must be
a noncombustible material such as ceramic wall tiles.
The following
Standards Codes Of Practice: BS 5440 Part 2
requirements must be observed:
behind via a safety chain and hook. (fig.B)
Fig. BFig. B
(900mm - 915mm). To allow alignment with a worktop
of greater than 915mm (max 940mm), longer
adjustable feet are available as a spare part on
request.
of adjustable feet in the base of the product
(900mm - 915mm). To allow alignment with a worktop
of greater than 915mm (max 940mm), longer
adjustable feet are available as a spare part on
request.
9
The cooker should be connected to the
gas-supply by a gas safe registered installer.
Connection of the appliance to the gas
mains or liquid gas must be carried out according to
the prescribed regulation in force, and only after it is
ascertained that it is adaptable to the type of gas to
be used. If not, follow the instructions indicated in
the paragraph headed “Adaptation to different gas
types”. In the case of connection to liquid gas, by
tank, use pressure regulators that conform to the
regulation in force. The gas supply must be
connected to the left of the appliance. Be sure that
the hose does not pass through the rear of the
cooker touching hot parts.
Make sure the supply pressure conforms with the
values shown in the table entitled “Caracteristics of
the burners and nozzles”.
When the cooker is installed between
cabinets (recessed), the gas connection
must be effected by an approved flexible
hose with bayonet fitting
(BS 669 or EN 14800). The gas inlet f or
the cookers is a threaded G 1/2 gas female
f i t t i n g .
Connecting the gas supply
To make the connection, a flexible hose should be
used corresponding to the current gas regulations
which are:
• the hose must never be at any point in its
lenght in contact with the “hot” parts
of the cooker;
• the hose must never be longer than 1,5 metre;
• the hose must not be subject to any tension
or torsional stress and it must not have any
excessively narrow curves or bottlenecks;
• the hose must be easy to inspect along its
entire length to check its condition;
• the hose must always be in good condition,
never attempt to repair.
Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of
gas with respect to the gas for which it was
produced follow these steps:
a)a)a)a)a) replace the hose holder mounted on the
appliance with that supplied in the bag of “cooker
accessories”.
b)b)b)b)b) Replacing the burner nozzles on the hob:
•remove the grids and slide the burners from their
housings;
• unscrew the nozzles
using a 7 mm socket
spanner, and replace
them with nozzles for
the new type of gas
(see table 1 “Burner and
nozzle characteristics”).
•replace all the
components by
repeating the steps in
reverse order.
INSTALLATION TIPS
c )c )c )c )c ) Minimum regulation of the hob burners:
• turn the tap to minimum;
• remove the knob and adjust
the regulation screw, which is
positioned in or next to the tap
pin, until the flame is small
but steady.
In the case of liquid gas, the regulation screw
must be adjusted to the minimum setting.
• check that the flame does not turn off when
you turn the tap quickly from high to low.
d )d )d )d )d ) Regulating the primary air of the burners:
The primary air of the burners requires no regulation.
EN
WARNING : This operation must be perfomed
by a qualified technician
On completion of the operation, replace the old rating
sticker with one indicating the new type of gas used.
Gas connection
V
V
Z
• Pry the fixing tab “V” and remove the oven burner
• Unscrew the oven burner nozzle using the socket
spanner for the nozzles “Z”“Z”
“Z”“Z”“Z”, or a 7 mm socket
spanner, and replace it with a nozzle suited to the
new type of gas (see Table 1).
Take particular care handling the spark plug
wires and the thermocouple pipes.
• Replace all the parts, following the steps
described above in the reverse order.
b )b )
b )b )
b ) Minimum regulation of the main and top gas
oven burner with thermostat:
• light the burner as described in the
paragraph the oven knob” of the
instruction booklet.
• turn the knob to MaxMax
MaxMaxMax for about 10 minutes
and then turn the knob to the MinMin
MinMin
Min
setting;
• remove the knob;
• regulate the screw positioned outside the
thermostat pin until the flame is
small but steady.
! !
! ! In the case of liquid gas, the regulation screw
must be screwed in to the bottom.
• check that the burner does not turn off whenwhen
you turn the knob from Max to Min and and
when you open and close the oven door quickly.
Adapting the gas grill to different types of gas
Replacing the nozzle of the grill burner:
On completion of the operation, replace the old
rating sticker with one indicating the new type of gas
used. This sticker is available from our Service
Centres.
Not eNot e
Not eNot eNot e
Should the pressure of the gas used be different (or
vary) from the recommended pressure, it is
necessary to fit a suitable pressure regulator onto
the inlet pipe in compliance with current National
Regulations relative to “regulators for channelled
gas”.
If the appliance is connected to a liquid gas supply, the
bypass screw must be set to a minimum.
While the burner is alight, quickly change the position of the
knob from minimum to maximum and vice versa several times,
checking that the flame is not extinguished.
Upon completion of adjustment, reseal using sealing
wax or an equivalent material.
1. Remove the enamelled baffle at the front of the grill
(2 screws).
2. Remove the screw on the right hand side of the
burner and gently slide the burner off the injector.
3. Using a 7mm socket, replace the grill injector as
appropriate (see table on previous page).
4. Re-assemble the burner and baffle.
INSTALLATION TIPS
Adapting to different types of gas (main and top
oven)
In order to adapt the oven to a different type of gas
with respect to the gas for which it was
manufactured (indicated on the label), follow these
simple steps:
a)a)a)a)a) Replacing the oven burner nozzle
• open the oven door fully
• pull out the sliding oven bottom
unscrew the two screws and take o the shield
protecting the burner (in main oven burner only).
10
V
V
Z
• Pry the fixing tab “V” and remove the oven burner
• Unscrew the oven burner nozzle using the socket
spanner for the nozzles “Z”“Z”
“Z”“Z”“Z”, or a 7 mm socket
spanner, and replace it with a nozzle suited to the
new type of gas (see Table 1).
Take particular care handling the spark plug
wires and the thermocouple pipes.
• Replace all the parts, following the steps
described above in the reverse order.
b )b )
b )b )
b ) Minimum regulation of the main and top gas
oven burner with thermostat:
• light the burner as described in the
paragraph the oven knob” of the
instruction booklet.
• turn the knob to MaxMax
MaxMaxMax for about 10 minutes
and then turn the knob to the MinMin
MinMin
Min
setting;
• remove the knob;
• regulate the screw positioned outside the
thermostat pin until the flame is
small but steady.
! !
! ! In the case of liquid gas, the regulation screw
must be screwed in to the bottom.
• check that the burner does not turn off whenwhen
you turn the knob from Max to Min and and
when you open and close the oven door quickly.
Adapting the gas grill to different types of gas
Replacing the nozzle of the grill burner:
On completion of the operation, replace the old
rating sticker with one indicating the new type of gas
used. This sticker is available from our Service
Centres.
Not eNot e
Not eNot eNot e
Should the pressure of the gas used be different (or
vary) from the recommended pressure, it is
necessary to fit a suitable pressure regulator onto
the inlet pipe in compliance with current National
Regulations relative to “regulators for channelled
gas”.
If the appliance is connected to a liquid gas supply, the
bypass screw must be set to a minimum.
While the burner is alight, quickly change the position of the
knob from minimum to maximum and vice versa several times,
checking that the flame is not extinguished.
Upon completion of adjustment, reseal using sealing
wax or an equivalent material.
1. Remove the enamelled baffle at the front of the grill
(2 screws).
2. Remove the screw on the right hand side of the
burner and gently slide the burner off the injector.
3. Using a 7mm socket, replace the grill injector as
appropriate (see table on previous page).
4. Re-assemble the burner and baffle.
INSTALLATION TIPS
Adapting to different types of gas (main and top
oven)
In order to adapt the oven to a different type of gas
with respect to the gas for which it was
manufactured (indicated on the label), follow these
simple steps:
a)a)a)a)a) Replacing the oven burner nozzle
• open the oven door fully
• pull out the sliding oven bottom
unscrew the two screws and take o the shield
protecting the burner (in main oven burner only).
EN
WARNING : This operation must be perfomed
by a qualified technician

Produktspecifikationer

Varumärke: Hotpoint
Kategori: Ugn
Modell: HDM67G0CCW/UK

Behöver du hjälp?

Om du behöver hjälp med Hotpoint HDM67G0CCW/UK ställ en fråga nedan och andra användare kommer att svara dig


Ugn Hotpoint Manualer

Hotpoint

Hotpoint HTX8017DCF2 Bruksanvisning

9 April 2025
Hotpoint

Hotpoint HS68M8PCX Bruksanvisning

5 Januari 2025
Hotpoint

Hotpoint HB 0577B NE Bruksanvisning

31 December 2025
Hotpoint

Hotpoint H6GG1F (X) IT Bruksanvisning

31 December 2025
Hotpoint

Hotpoint FA4S 844 P IX HA Bruksanvisning

31 December 2025
Hotpoint

Hotpoint H6TMH2AF (X) IT Bruksanvisning

31 December 2025
Hotpoint

Hotpoint FIT 804 H AV HA Bruksanvisning

15 December 2024
Hotpoint

Hotpoint PCN 640 T (AN) R /HA Bruksanvisning

15 December 2024
Hotpoint

Hotpoint FIT 834 AN HA Bruksanvisning

15 December 2024
Hotpoint

Hotpoint PCN 750 T (OW) R /HA Bruksanvisning

15 December 2024

Ugn Manualer

Nyaste Ugn Manualer

Siemens

Siemens HB23A1520S Bruksanvisning

9 April 2025
Whirlpool

Whirlpool akp 237 Bruksanvisning

9 April 2025
BEKO

BEKO BQM24400BPS Bruksanvisning

9 April 2025
Stoves

Stoves SEH700CTC Bruksanvisning

9 April 2025
Koenic

Koenic KBO 42211 Bruksanvisning

9 April 2025
Novamatic

Novamatic FH67-412K Bruksanvisning

9 April 2025
Smeg

Smeg c 9 gvx be Bruksanvisning

9 April 2025
Korona

Korona 57157 Bruksanvisning

9 April 2025
Miele

Miele CSAD 1400 Bruksanvisning

9 April 2025
Ignis

Ignis AKH 2012 IX Bruksanvisning

9 April 2025