IBEAM TE-DGH Bruksanvisning

IBEAM Inte kategoriserad TE-DGH

Läs nedan 📖 manual på svenska för IBEAM TE-DGH (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
REV. 05/21/2018
TE-DGH/TE-DGHC (CMOS)
RAM 1500 (2009-2017)
RAM 2500 (2010-2017)
Replacement Tailgate Handle
with Camera
Removal and Installation
Instructions
Tools Needed: T30 torx bit, ratchet, 8mm
socket.
1. Start by lowering the tailgate and remove
the (8) T30 torx screws from the bed liner,
remove liner (Fig. A), remove access panel
(Fig. B), and place aside.
2. Now that you have access to the handle
assembly, disconnect harness running to lock
actuator and unclip (2) latch rods. (Fig. C)
3. Next, remove (2) 8mm nuts located below
latch connectors, then slide latch assembly
aside. (Fig. C)
4. Gently remove handle by lifting the handle
from the outside and slowly working it out.
5. Now that the handle is out of the tailgate,
you will have to swap the locking mechanism
out of the old handle to the new one.
6. Start by removing the (2) 8mm screws from
locking mechanism, and then remove
mechanism from handle. (Fig. D)
7. Now place the locking mechanism in the new
handle and secure it with the factory 8mm
screws.
Fig. A
Fig. B
Fig. C
8. Next, remove taillight and splice the red
power wire from the camera’s harness into
the reverse light’s 12v positive wire. This will
trigger the camera to turn on when vehicle is
placed in reverse. Attach the black ground
wire to a metal non-painted surface.
9. Wires can now be fully routed from the
tailgate to the cab of the truck and to a video
source . The Yellow RCA, securing every 16”
will plug into the input of your video source;
the Red wire goes to the rear camera input
trigger wire on your video source.
NOTE: Test to make sure video is working
before securing new handle.
NOTE: If desired, parking lines can be
removed by cutting the green loop wire.
10. Now gently reinsert new tailgate handle and
route cable trough tailgate.
NOTE: Avoid pinching cable running to
camera
11. Realign the handle’s post with latch assembly
opening mechanism and reattach 8mm nuts
to secure handle in tailgate.
12. Reconnect harness to lock actuator and
reattach latch rods, then reattach the
tailgate’s access panel and bed liner cover to
complete your install.
1.800.221.0932
www.iBeamUSA.com
460 Walker Street Holly Hill, FL 32117 ,
Fig. D
REV. 05/21/2018

Produktspecifikationer

Varumärke: IBEAM
Kategori: Inte kategoriserad
Modell: TE-DGH

Behöver du hjälp?

Om du behöver hjälp med IBEAM TE-DGH ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad IBEAM Manualer

IBEAM

IBEAM TE-GMSH Bruksanvisning

24 September 2024
IBEAM

IBEAM TE-FTGC Bruksanvisning

23 September 2024
IBEAM

IBEAM TE-BPCIR Bruksanvisning

20 September 2024
IBEAM

IBEAM TE-THC Bruksanvisning

20 September 2024
IBEAM

IBEAM TE-CLED Bruksanvisning

20 September 2024
IBEAM

IBEAM TE-50VS Bruksanvisning

19 September 2024
IBEAM

IBEAM TE-MDC Bruksanvisning

19 September 2024
IBEAM

IBEAM TE-DGH Bruksanvisning

19 September 2024
IBEAM

IBEAM TE-BPC Bruksanvisning

19 September 2024
IBEAM

IBEAM TE-RMH Bruksanvisning

19 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 55PUS6551 Bruksanvisning

16 Januari 2025
Philips

Philips 32PHS4504 Bruksanvisning

16 Januari 2025
Electrolux

Electrolux RH36WC40GS Bruksanvisning

16 Januari 2025
Rocstor

Rocstor SolidKVM SK05 Bruksanvisning

16 Januari 2025
Carlsbro

Carlsbro CSD25M Bruksanvisning

16 Januari 2025
Carlsbro

Carlsbro CSD45M Bruksanvisning

16 Januari 2025
Carlsbro

Carlsbro CSD35M Bruksanvisning

16 Januari 2025
On-Q

On-Q EN2050 Bruksanvisning

16 Januari 2025
On-Q

On-Q EN1420 Bruksanvisning

16 Januari 2025
Chief

Chief Kontour KRA300B Bruksanvisning

16 Januari 2025