Icom AT-140 Bruksanvisning

Icom mottagare AT-140

Läs nedan 📖 manual på svenska för Icom AT-140 (12 sidor) i kategorin mottagare. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/12
2001 NEW
HF AUTOMATIC
ANTENNA TUNER
AT-140
INSTRUCTION MANUAL
AT-140_1.qxd 04.4.26 9:16 Page 1
i
2001 NEW 2001 NEW
FOREWORD
Thank you for purchasing the AT-140 HF AUTO-
MATIC ANTENNA TUNER.
The AT-140 is designed, primarily for use with Icom HF
transceivers.
Refer to your HF transceiver instruction manual for op-
eration. If you have any questions, contact your dealer.
IMPORTANT
READ ALL INSTRUCTIONS carefully and com-
pletely before using the AT-140.
SAVE THIS INSTRUCTION MANUAL. This in-
struction manual contains important safety and instal-
lation instructions.
EXPLICIT DEFINITIONS
PRECAUTIONS
RDANGER HIGH VOLTAGE! NEVER touch
the antenna terminal, ground terminal, antenna or
counterpoise while transmitting. Place the AT-140, an-
tenna and counterpoise in positions where no one can
touch them.
NEVER use without a ground connection.
NEVER transmit during internal adjustment. This may
cause an electric shock.
USE the ground terminal for ground connection.
The mounting plate is not connected internally.
DO NOT operate your HF marine transceiver without
running the boat’s engine.
AVOID using the AT-140 in areas where the temper-
ature is below –30°C (–22°F) or above +60°C
(+140°F).
Ground terminal
Mounting plate
Word Definition
RWARNING Personal injury, re hazard or electric
shock may occur.
CAUTION Equipment damage may occur.
NOTE
If disregarded, inconvenience only. No
personal injury, re hazard or electric
shock.
SUPPLIED ACCESSORIES
The following accessories are supplied with the AT-140. Qty.
qU-bolts ……………………………………………… 2
wU-bolt plates ……………………………………… 2
eFlat washers (M6 large) ………………………… 8
rFlat washers (M6 small) ………………………… 4
tSpring washers (M6) ……………………………… 8
yNuts (M6) …………………………………………… 8
uHex head bolts (M6×50) ………………………… 4
iSelf-tapping screws (A0 6×30) …………………… 4
oWeatherproof cap ………………………………… 1
!0 4-pin/6-pin connector* …………………………… 1
!1 Connector pins* …………………………………… 4
!2 Ground cable (OPC-412) ………………………… 1
*The supplied connector and pins are differ according to ver-
sion.
q
w
e
r
t
y
u
i
o
!0 !1
!2
Icom, Icom Inc. and the are registered trademarks of Icom Incorporated (Japan) in the United States, the United King-
dom, Germany, France, Spain, Russia and/or other countries.
AT-140_1.qxd 04.4.26 9:16 Page 2
ii
2001 NEW
MISCELLANEOUS ITEMS
The following parts are additionally required for instal-
lation, but are not supplied with the AT-140.
Purchase these parts locally.
qAWG 14×4-conductor shielded cable
*Icom offers an optional OPC-1147/N
CONTROL CABLE
.
Length: 10 m; 32.8 feet
w50 coaxial cable
ePL-259 connectors
FEATURES
Matches all bands
The AT-140 matches any frequency on every HF ma-
rine band. For example, the tuner matches a 7 m; 23 ft
long-wire antenna across 1.630 MHz.
Full automatic tuning
Just push the [TUNE] switch on the transceiver, and
the AT-140 adjusts immediately to the minimum SWR
of any frequency on any HF marine band.
HF operation on any size ship
The AT-140 allows you HF operation where antenna
element length is restricted due to space.
Weather resistant
The AT-140 is housed in a durable, completely weather
resistant ASA case with a rubber gasket. The antenna
tuner can be conveniently installed both on the deck or
in the cabin near the antenna element.
Simple installation
Installation is simple. Just connect the control and an-
tenna cables. You never need to open the cover.
45 memories for shorter tuning time
To decrease the tune-up time, the AT-140 automatically
stores the matching conditions for up to 45 frequencies.
Re-tuning for a memorized frequency takes approx. 1
sec.
Super capacitor for memory backup
Even if the AT-140 is not used for approx. 1 week, the
built-in super capacitor backs up contents of the 45
memories.
Low power tune up
The AT-140 emits low output power during tuning. This
feature reduces the possibility of causing interference
to other stations.
Tuner through function
The tuner through function is built into the AT-140. This
function helps improve receiver gain, depending on the
antenna element length used, and operating fre-
quency.
TABLE OF CONTENTS
FOREWORD …………………………………………… i
IMPORTANT …………………………………………… i
EXPLICIT DEFINITIONS ……………………………… i
PRECAUTIONS ……………………………………… i
SUPPLIED ACCESSORIES ………………………… i
MISCELLANEOUS ITEMS ………………………… ii
FEATURES …………………………………………… ii
TABLE OF CONTENTS ……………………………… ii
1 ANTENNA SYSTEM …………………………… 1–2
Antenna for ship ………………………………… 1
Antenna for land operation ……………………… 1
Coaxial cable …………………………………… 2
Ground and counterpoise ……………………… 2
2 INSTALLATIONS ………………………………… 3–5
lnstallation outline………………………………… 3
Control cable……………………………………… 3
PL-259 connector………………………………… 4
Mounting ………………………………………… 4
Cable connections ……………………………… 5
3 CONTROL CABLE SIGNALS ………………… 6–7
Terminal information …………………………… 6
Transceiver setting ……………………………… 7
4 UNIT DESCRIPTION AND SPECIFICATIONS
………………………………………………………… 8
Unit description…………………………………… 8
Specications …………………………………… 8
AT-140_1.qxd 04.4.26 9:16 Page 3

Produktspecifikationer

Varumärke: Icom
Kategori: mottagare
Modell: AT-140

Behöver du hjälp?

Om du behöver hjälp med Icom AT-140 ställ en fråga nedan och andra användare kommer att svara dig




mottagare Icom Manualer

Icom

Icom IC-M15 Bruksanvisning

14 Oktober 2024
Icom

Icom IC-M120 Bruksanvisning

29 September 2024
Icom

Icom IC-502A Bruksanvisning

28 September 2024
Icom

Icom IC-T7H Bruksanvisning

27 September 2024
Icom

Icom IC-M600E Bruksanvisning

22 September 2024
Icom

Icom IC-471H Bruksanvisning

22 September 2024
Icom

Icom IC-PS25 Bruksanvisning

20 September 2024

mottagare Manualer

Nyaste mottagare Manualer