IFM O1D105 Bruksanvisning

IFM Inte kategoriserad O1D105

Läs nedan 📖 manual på svenska för IFM O1D105 (27 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/27

Operating instructions

Optical distance sensor

O1D105

11454899 / 00 04 / 2019

Content

1 Preliminary note 4 ��

1�1 Symbols used 4 ��

1�2 Warning signs used 4 ��

2 Safety instructions 4 ��

3 Functions and features 6 ��

3�1 Applications ��6

4 Functions ��6

4�1 Output function hysteresis 6 ��

4�2 Output function window 6 ��

4�3 Analogue output function 6 ��

4�4 Switch off the laser 6 ��

5 Installation��7

5�1 Installation conditions 7 ��

5�2 Mounting accessories 7 ��

6 Electrical connection 8 ��

6�1 Operation with IO-Link master 8 ��

7 Operating and display elements 9 ��

8 Menu ��10

8�1 Menu structure 10 ��

8�2 Explanation of the menu �� 11

9 Operating modes 13 ��

9�1 Run mode 13 ��

9�2 Display mode 13 ��

9�3 Object reflectivity 13 ��

9�4 Programming mode 13 ��

10 Parameter setting 14 ��

10�1 Parameter setting in general 14 ��

10�1�1 Setting of the parameter value 14 ��

10�1�2 Change from menu level 1 to menu level 2 15 ��

10�1�3 Electronic lock 15 ��

10�2 Configuration of the basic settings 16 ��

10�2�1 Selection of the display unit 16 ��

10�2�2 Setting of the display 16 ��

10�2�3 Configuration of OUT1 16 ��

10�2�4 Hysteresis function 17 ��

10�2�5 Setting of the switch point for hysteresis function OUT1 18 ��

10�2�6 Window function 18 ��

10�2�7 Setting of the switch points for window function OUT1 19 ��

10�2�8 Configuration of OUT1 20 ��

10�2�9 Setting of the switch point for hysteresis function OUT2 20 ��

10�2�10 Setting of the switch points for window function OUT2 20 ��

10�2�11 Scaling of the measuring range (analogue output) 20 ��

10�3 Teach mode 22 ��

10�3�1 Setting of the sampling rate 22 ��

10�3�2 Setting of the repeatability 22 ��

10�3�3 Table repeatability and accuracy 23 ��

10�4 Extended functions 24 ��

10�4�1 Setting of the time delay for switching outputs 24 ��

10�4�2 Setting of the fault suppression time for switching outputs / analogue

output 24 ��

10�4�3 Reset of all parameters to factory setting 24 ��

10�4�4 Display of the software version number 24 ��

11 IO-Link ��25

11�1 General information 25 ��

11�2 Device-specific information 25 ��

11�3 Parameter setting tools 25 ��

11�4 Extended functions 25 ��

11�4�1 Teach function 25 ��

11�4�2 Object reflectivity 25 ��

12 Set-up / operation 25 ��

12�1 Fault indication 26 ��

13 Maintenance, repair and disposal 27 ��

14 Factory setting 27 ��

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference�

Information

Supplementary note�

1.2 Warning signs used

WARNING

Warning of serious personal injury�

Death or serious irreversible injuries may result�

2 Safety instructions

• Please read this document prior to set-up of the unit� Ensure that the product is

suitable for your application without any restrictions�

• Improper or non-intended use may lead to malfunctions of the unit or to

unwanted effects in your application� That is why installation, electrical

connection, set-up, operation and maintenance of the unit must only be carried

out by qualified personnel authorised by the machine operator�

• In case of malfunction of the unit please contact the manufacturer� If the unit is

tampered with and/or modified, any liability and warranty is excluded�

WARNING

Visible laser light; laser protection class 2�

Use of controls or adjustments other than those specified herein may result in hazardous

radiation exposure� Damage to the retina is possible�

►Do not stare into the laser beam!

►Apply the enclosed labels (laser warning) in the immediate vicinity of the unit�

►Adhere to the caution and warning notes on the product label�

►Use the enclosed label for the power supply cable�

►EN/IEC 60825-1 : 2007 and EN/IEC 60825-1 : 2014 complies with 21 CFR 1040

except for deviations pursuant to Laser Notice No� 50, dated June 2007

Label for supply cable

Product label

3 Functions and features

The unit is used as an optical distance sensor�

3.1 Applications

• The optical distance sensor measures distances between 0�2 and 10 m�

• It has a background suppression at > 10��100 m�

• The measured value is shown in a 10-segment display�

• According to the set output functions 2 output signals can be generated�

4 Functions

4.1 Output function hysteresis

The hysteresis keeps the switching state of the output stable if the measured

value varies about the sensing range� Both outputs (OUT1 and OUT2) can be set

as hysteresis function� → 10.2.4 Hysteresis function

4.2 Output function window

The window function enables the monitoring of a defined acceptable range� Both

outputs (OUT1 and OUT2) can be set as window function� → 10.2.6 Window function

4.3 Analogue output function

The sensor can also output an analogue signal on output 2 (OUT2) which is proportional

to the distance� → 10.2.11 Scaling of the measuring range (analogue output)

4.4 Switch off the laser

For safety and maintenance purposes the laser of the unit can be temporarily

switched off via the input on pin 5�

Input signal at pin 5 Laser

Low / not connected On

High Off

5 Installation

5.1 Installation conditions

►Install the unit so that the object to be detected is within a measuring range of

0�2��10 m�

The unambiguity range of the sensor is fixed to 100 m� Objects within a range

> 10…100 m are suppressed�

Reflecting objects in the direct beam path of the sensor - also in the range

> 100 m – are to be avoided by the customer� Otherwise the measured

values may be ambiguous�

5.2 Mounting accessories

The unit is supplied without mounting accessories�

Examples of mounting accessories Art. no.

Protective cover O1D E21133

Mounting set E2D101 + E20938 + E20951 E21079

Mounting set O1D (for rod mounting Ø 12 mm) E2D101

Mounting rod straight Ø 12 mm / M10 E20938

Mounting set O1D (for rod mounting Ø 14 mm) E2D111

Mounting rod straight Ø 14 mm / M12 E20939

Fixture for mounting and fine adjustment of O1D laser units

(rod or free-standing; depending on the clamp) E1D100

Example mounting:

1: Mounting set for Ø 12 mm rod

art� no� E2D101

2: Mounting rod straight Ø 12 mm / M10

art� no� E20938

6 Electrical connection

The unit must be connected by a qualified electrician�

►The national and international regulations for the installation of electrical

equipment must be adhered to�

►Ensure voltage supply according to EN 50178, SELV, PELV�

O1D105: cULus, Supply Class 2

►Disconnect power�

►Connect the unit as follows:

O1D105 PNP

2 1

L+

2: OUT2

4: OUT1

2: OUT2

4: OUT1

Core colours of ifm sockets:

1 = BN (brown), 2 = WH (white), 3 = BU (blue), 4 = BK (black), 5 = GR (grey)�

6.1 Operation with IO-Link master

The unit is compatible with IO-Link master port class A (type A)�

For operation with IO-Link master port class B (type B) observe the following:

As a standard, the unit is not compatible with master port class B (type B)�

Pin 2 (OU2) and pin 5 (IN1) are used for manufacturer-specific functions�

That means that the main supply voltage of the unit and the additional

voltage supply (master port class B on pins 2/5) are not electrically isolated�

With the following configurations the unit can be used with master port class B:

• Connect unit and IO-Link master via 3 wires: Connect pins 1, 3 and 4 of the

unit with the IO-Link master (do not connect pins 2 and 5)�

• Connect unit and IO-Link master via 4 wires: Deactivate pin 2 (OU2) via IO-

Link (setting OU2 = "off") and connect pins 1, 2, 3 and 4 of the unit with the

IO-Link master (do not connect pin 5)�

7 Operating and display elements

1: 4 x LED green Lighting LED = power and set display unit (mm, m, inch)

2: 4 x LED yellow

(two not

connected)

Indication of the switching status; lights, if the corresponding

output is switched�

3: 4-digit

alphanumeric

display

Indication of the measured distance, the parameters and

parameter values�

4: Programming

button

[SET]

Setting of the parameter values (scrolling by holding pressed;

incrementally by pressing once)�

5: Programming

button

[MODE/ENTER]

Selection of the parameters and acknowledgement of the

parameter values�

8 Menu

8.1 Menu structure

= [MODE / ENTER] = [SET]

8.2 Explanation of the menu

For the factory settings please refer to the end of these instructions

(→ 14 Factory setting)�

Configuration for output 1

4 switching functions can be selected:

[Hno], [Hnc], [Fno], [Fnc] → 10.2.3 Configuration of OUT1

Switch point for hysteresis function OUT1

Limit value at which the output with selected hysteresis function changes

its switching state (object nearer/farther than distance set)�

[SP1] is only active if [OU1] = [Hno] or [Hnc]�

→ 10.2.5 Setting of the switch point for hysteresis function OUT1

Switch points for window function OUT1

Limit values at which the output with selected window function changes its

switching state (object present / not present between the distance "near"

and the distance "far")�

[nSP1] = switch point “near” / [FSP1] = switch point “far”�

[nSP1] / [FSP1] are only active if [OU1] = [Fno] or [Fnc]�

→ 10.2.7 Setting of the switch points for window function OUT1

Configuration for output 2

4 switching functions and 2 analogue signals can be selected:

[Hno], [Hnc], [Fno], [Fnc], [I], [U] → 10.2.8 Configuration of OUT1

Switch point for hysteresis function OUT2

Limit value at which the output with selected hysteresis function changes

its switching state (object nearer/farther than distance set)�

[SP2] is only active if [OU2] = [Hno] or [Hnc]�

→ 10.2.9 Setting of the switch point for hysteresis function OUT2

Switch points for window function OUT2

Limit values at which the output with selected window function changes its

switching state (object present / not present between the distance "near"

and the distance "far")�

[nSP2] = switch point “near” / [FSP2] = switch point “far”�

[nSP2] / [FSP2] are only active if [OU2] = [Fno] or [Fnc]�

→ 10.2.10 Setting of the switch points for window function OUT2

Analogue start point

Measured value at which 4 mA / 0 V are provided�

[ASP] is only active if [OU2] = [I] or [U]�

→ 10.2.11 Scaling of the measuring range (analogue output)

Analogue end point

Measured value at which 20 mA / 10 V are provided�

[AEP] is only active if [OU2] = [I] or [U]�

→ 10.2.11 Scaling of the measuring range (analogue output)

Teach mode

Selection "sampling rate" or "repeatability"

→ 10.3 Teach mode

Extended functions

Press [SET] to open the submenu "Extended functions"

→ 10.4 Extended functions

Delay for the switching outputs

[dSx] = switch-on delay; [drx] = switch-off delay�

The output does not immediately change its switching status when the

switching condition is met but only after the delay has elapsed� If the

switching condition is no longer met after the delay has elapsed, the

switching status of the output does not change�

[dS2] and [dr2] are not effective if [OU2] = [I] or [U]�

→ 10.4.1 Setting of the time delay for switching outputs

Damping of the measured signal

This function allows to suppress short-time saturation of the measuring

element (such saturation can result from direct reflection or strong

fluctuations in brightness)�

During the delay set, the latest valid value measured is displayed, the

output signals remain unchanged�

→ 10.4.2 Setting of the fault suppression time for switching outputs /

analogue output

Display setting

7 settings can be selected:

[d1], [d2], [d3], [rd1], [rd2], [rd3], [OFF]

→ 10.2.2 Setting of the display

Setting of the display unit

Selection of the unit of measurement for [SP1], [SP2], [ASP], [AEP]

Selection options: [mm] [m] [inch]

→ 10.2.1 Selection of the display unit

Restore factory setting

→ 10.4.3 Reset of all parameters to factory setting

Display of the software version number

→ 10.4.4 Display of the software version number

9 Operating modes

9.1 Run mode

The run mode is the normal operating mode�

After power on the unit is in the Run mode� It carries out its monitoring function

and generates output signals according to the set parameters�

The display indicates the current distance, the yellow LEDs signal the switching

status of the outputs�

9.2 Display mode

Indication of the parameters and the set parameter values�

►Press [MODE/ENTER] briefly�

> Unit goes to the Display mode� Internally it remains in the operating mode�

The set parameter values can be read�

►To scroll through the parameters, press [MODE/ENTER] briefly�

►To display the respective parameter value, press [SET] briefly�

> After 15 s the unit returns to the Run mode�

9.3 Object reflectivity

Display of the object reflectivity (formerly: align mode)�

►Press [SET] in the Run mode�

> The unit displays an orientation value for the object reflectivity

(e�g� +100 corresponds to a white object, +020 corresponds to a grey object)�

9.4 Programming mode

Setting the parameter values �→ 10.1 Parameter setting in general

Produktspecifikationer

Varumärke:	IFM
Kategori:	Inte kategoriserad
Modell:	O1D105
Typ av operation:	Draaiknop
Färg på produkten:	Zilver
Timer:	Ja
Bredd:	152 mm
Djup:	177 mm
Höjd:	233 mm
Beeldscherm:	Nee
Indikator ljus:	Ja
Justerbar termostat:	Ja
Ström LED:	Ja
Värmekraft:	1500 W
Placeringsalternativ:	Floor, Table
Värmeeffekt (min):	- W