Inverto Black Pro Bruksanvisning
Läs nedan 📖 manual på svenska för Inverto Black Pro (4 sidor) i kategorin Växla. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/4
Technical parameters
Inputs 4 x IF inputs from Quattro LNB
1 x UHF/VHF input from Terrestrial antenna
Outputs 4 x loopthrough satellite IF outputs
1 x loopthrough terrestrial output
1 x Legacy output to connect to legacy receiver with combined
terrestrial signal
1 x Unicable output to connect up to 8 receiver tuners with com-
bined terrestrial signal
Frequency range Satellite: 950-2150MHz
Terrestrial: 47-862MHz
Loopthrough loss Satellite: max -3dB
Terrestrial: max -3dB
Gain Satellite: 10dB (min)
Terrestrial: no amplification
Isolation Satellite-Satellite outputs: min 30dB
Satellite-Terrestrial : min 35dB
Control protocol DiSEqC™ commands extension according to CENELEC
prEN50494
Power consumption 20VDC, 380mA
Dimensions (W x H x D mm) W=138.82 H=203.2 D=18.74 mm
Temperature range -20C - +60C
AC/DC adaptor Input voltage: 90-265VAC, 50/60Hz
Output voltage: 20VDC
Output current: 600mA
Short circuit protection: None
Troubleshooting
Make sure the satellite antenna and LNB are properly fixed, connected and adjusted and that the sat-
ellite receivers are installed, connected and switched on according to available instructions.
Ensure there is no short circuit on the product inputs. This will prevent power to the LNB. If this is the
case, disconnect the product from the main power, and then find and remove the short circuit on the
product inputs. Then re-connect the multiswitch to the main power.
Frequent defects are in connector joints i.e. if the central conductor is too short and fails to make
contact in the connector. Also the shielding braid should make proper contact with the connector coat.
Sometimes a reset to the multiswitch microprocessor is sufficient to remove a fault: simply disconnect
the multiswitch from main power for 30 seconds and then reconnect again.
If you are unable to remove the fault yourself, please contact your distributor.
Disposal
Following relevant EU directives, this device shall not be disposed of together with municipal waste.
Use local waste collection and recycling systems to dispose wore out products.
*DiSEqC™ is a registered trademark of Eutelsat
*For purpose of brevity, some product descriptions in this sheet remain at platform level and may not be
referred to as detailed datasheets of the products. Inverto Digital Labs reserves the right to amend, omit or
add products, product-lines, and/ or features without notice.
Installation manual
Unicable™ Multiswitch
IDLP-UST111-CU010-8PP
4
V100214
Satellite - Input
Satellite - Input
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
M a d e i n C h i n a
D e s ig n e d i n L U
TM
Satellite - loop-through output
+
Connect the cables from the Quattro LNB to the input connectors marked with LNB V/L, V/H, H/L and
H/H inputs (pay attention to identification of the Quattro LNB connectors). The multiswitch is equipped
with Terrestrial input. Connect the Terrestrial antenna to this input:
Satellite - Input
Satellite - Input
There are two output connectors: Legacy and Unicable.
The Legacy output is a standard Universal switching output that allows to connect a legacy receiver that
is not supporting the Unicable protocol.
The Unicable output allows to connect up to 8 receiver tuners – each needs to be allocated one of the
8 user bands supported by the multiswitch.
Each receiver tuner is assigned with 1 out of 8 communication channel frequencies (user band). The
frequencies are listed on the product sticker:
For optimized performance, please follow the recommendations below:
1. -use the highest frequency for a wall socket located the nearest to the multiswitch and use the low
est frequency for wall socket located farest to the multiswitch.
2. If you install less than 8 receiver tuners, use the lowest frequencies first. We also recommend
to keep record of the user bands allocated to the different connections as these user bands will
then have to be set in the receiver. The satellite receivers connected to the multiswitch have to be
Unicable-compatible (usually marked with Unicable™ logo).
Note: Loopthrough outputs that are not used should be terminated with 75ohm DC-blocked
terminations.
Safety
Never open a powered product. This may result in electrical hazard.
Never work on the product, TV set or other powered devices during or before a storm. A lightning strike
into the antenna may cause dangerous overvoltage over the product’s metallic/conductive parts.
Make sure the local electricity network corresponds to the operating voltage of the AC/DC adaptor.
If the products gets into contact with liquid it must be disconnected from the main power.
It is recommended to disconnect the product from the main power if it is not used for long periods of
time.
When disconnecting the product don’t pull the cable but the plug to prevent damage of the cable (wob-
bly plugs and outlets result in fire risk).
The product shall be serviced by qualified experts only.
Thank you for purchasing Inverto’s advanced Unicable multiswitch and we are certain it will meet your
expectations.
Before installing and operating the product, please read the following instructions and recommenda-
tions. We suggest that you keep this manual for future use.
Warranty
The Unicable multiswitch is designed for the distribution of satellite and terrestrial television and radio
signals in home installations. The warranty does not apply for products used for other purposes than
those specified herein. The user/installer shall be responsible for any damage incurred as a result of not
using the product according to the instructions in this manual.
Installation location
The product shall be installed on a wall or other hard inflammable surface.
The product shall be in no case held only with the connected cables.
Place the product in a dry environment where it is not exposed to rain or running water.
Do not install the product close to heat sources or in places exposed to direct sunlight.
Product installation
The following diagram may assist you when drilling the holes:
To connect the product inputs and outputs use high-quality coaxial cables designed for satellite recep-
tion and F-connectors. Use a high-shielding coaxial cables with minimum 90dB.
If you use wall sockets to loopthrough the 8 user bands, make sure the wall sockets were designed
for satellite reception compatible with Unicable technology and allows bidirectional signal propagation.
The following diagram describes the installation configurations supported by the product:
Quattro
LNB
Terminated
Outputs
AC
AC
Legacy
x8 User bands
UB 7 UB 5 UB 3 UB 1
UB 6 UB 4 UB 2 UB 0
Legacy
x8 User bands
UB 7 UB 5 UB 3 UB 1
UB 6 UB 4 UB 2 UB 0
Power In
20V DC, 380mA
V/H H/L H/H
Terrestria l
input
Satellite - Input
V/L
Terrestria l
input S atellite - Input
V/H H/L H/HV/L
Terrestria l
output
Unicable Cascadable Switch
IDLP-UST111-CUO1O-8PP
Item: 3702
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Lo o p hroug h lo ss : 3dB-T
Terrestrial Loo p hro ugh lo s s: 3dB-T
Ma d e i n Ch i n a
Des i gn e d i n LU
Lega cy Out Unicable Out
TM
Sa tellite - loop -through output
+
V/H H/L H/HV/L [+Ter a l] [+Ter a lrestri restri ]
Power In
20V DC, 380mA
V/H H/L H/H
Terrestria l
input S ate llite - Input
V/L
Terrestria l
input S atellite - Input
V/H H/L H/HV/L
Terrestria l
output
Unicable Cascadable Switch
IDLP-UST111-CUO1O-8PP
Item: 3702
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz 1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satellite inputs: IF 950-2150MHz
Satellite Lo o p hroug h lo ss : 3dB-T
Terrestrial Loo p hro ugh lo s s: 3dB-T
Ma d e i n Ch i n a
Des i gn e d i n LU
Lega cy Out Unica ble Out
TM
Sa tellite - loop -through output
+
V/H H/L H/HV/L [+Ter a l] [+Ter a lrestri restri ]
2 3
83.256mm
188.83mm
20.59mm
Satellite - Input
Satellite - Input
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Satell ite input s: IF 950-2150MHz
Satell ite Loop-Through loss: 3dB
Terrestr ial Loop-Through loss: 3dB
M ade i n Ch i na
De si gned i n LU
TM
Satellite - loop-through output
+
Satellite - Input
Satellite - Input
User Bands:
0 : 1076.06MHz 4 : 1484.30MH z
1 : 1178.12MHz 5 : 1586.36MH z
2 : 1280.18MHz 6 : 1688.42MH z
3 : 1382.24MHz 7 : 1790.48MH z
Satelli te inputs: IF 950-2150MHz
Satelli te Loop-Thr ough loss: 3dB
Terrestrial Loop-Through loss: 3dB
M ade i n C hi na
De si gne d i n LU
TM
Satellite - loop-through output
+
User Bands:
0 : 1076.06MHz 4 : 1484.30MHz
1 : 1178.12MHz 5 : 1586.36MHz
2 : 1280.18MHz 6 : 1688.42MHz
3 : 1382.24MHz 7 : 1790.48MHz
Produktspecifikationer
| Varumärke: | Inverto |
| Kategori: | Växla |
| Modell: | Black Pro |
Behöver du hjälp?
Om du behöver hjälp med Inverto Black Pro ställ en fråga nedan och andra användare kommer att svara dig
Växla Inverto Manualer
21 September 2024
Växla Manualer
- Växla Bosch
- Växla IKEA
- Växla Huawei
- Växla HP
- Växla Panasonic
- Växla Honeywell
- Växla Yamaha
- Växla Alcatel
- Växla Alecto
- Växla Ansmann
- Växla Edimax
- Växla Intermatic
- Växla Flamingo
- Växla Brennenstuhl
- Växla Hikvision
- Växla Generac
- Växla Silvercrest
- Växla Nedis
- Växla Pyle
- Växla Renkforce
- Växla TP Link
- Växla Worx
- Växla Black Box
- Växla Elro
- Växla KlikaanKlikuit
- Växla Tripp Lite
- Växla DataVideo
- Växla Schneider
- Växla Theben
- Växla Chamberlain
- Växla Sylvania
- Växla Velleman
- Växla Tork
- Växla Techly
- Växla Emerson
- Växla Totolink
- Växla Vemer
- Växla Profile
- Växla Matrox
- Växla Steren
- Växla Perel
- Växla Engenius
- Växla Digitus
- Växla Kathrein
- Växla AV:link
- Växla Belkin
- Växla Linksys
- Växla Dahua Technology
- Växla Audiovox
- Växla Cotech
- Växla Netgear
- Växla LevelOne
- Växla Kaiser
- Växla QNAP
- Växla Boss
- Växla Shimano
- Växla Merten
- Växla Hager
- Växla Chacon
- Växla Elation
- Växla Sygonix
- Växla Planet
- Växla ZyXEL
- Växla Rex
- Växla Powerfix
- Växla Konig
- Växla Tesla
- Växla D-Link
- Växla Tenda
- Växla UPM
- Växla One For All
- Växla Finder
- Växla Marmitek
- Växla Delta Dore
- Växla Ubiquiti Networks
- Växla EBERLE
- Växla Grasslin
- Växla Omnitronic
- Växla Jung
- Växla CyberPower
- Växla Basetech
- Växla Trendnet
- Växla Mikrotik
- Växla WHALE
- Växla ATen
- Växla RGBlink
- Växla Gefen
- Växla Nexa
- Växla Adder
- Växla Wago
- Växla Homematic IP
- Växla Monoprice
- Växla Tiptel
- Växla OSD Audio
- Växla SPC
- Växla Crestron
- Växla Unify
- Växla ORNO
- Växla Berker
- Växla Provision ISR
- Växla Monacor
- Växla PCE
- Växla Logilink
- Växla Smart-AVI
- Växla StarTech.com
- Växla SIIG
- Växla Advantech
- Växla IOGEAR
- Växla Micro Connect
- Växla Extron
- Växla KanexPro
- Växla Blustream
- Växla Avocent
- Växla Intellinet
- Växla Ebode
- Växla Lancom
- Växla Robbe
- Växla B-tech
- Växla Speaka
- Växla Kopp
- Växla Vimar
- Växla Kemo
- Växla GAO
- Växla H-Tronic
- Växla Legrand
- Växla Kraus & Naimer
- Växla Noble
- Växla Intertechno
- Växla Ecler
- Växla Triax
- Växla Kramer
- Växla CYP
- Växla Suevia
- Växla Phoenix Contact
- Växla Seuthe
- Växla SmartAVI
- Växla Cudy
- Växla Lindy
- Växla Ernitec
- Växla Atlona
- Växla Adviti
- Växla Hamlet
- Växla Paladin
- Växla Equip
- Växla Noark
- Växla Vivolink
- Växla Cambium Networks
- Växla 2USB
- Växla Roline
- Växla KVM-TEC
- Växla AMX
- Växla BZBGear
- Växla STI
- Växla Epiphan
- Växla Mach Power
- Växla Axing
- Växla Juniper
- Växla Raritan
- Växla ConnectPro
- Växla SunBriteTV
- Växla Atlantis Land
- Växla GEV
- Växla Pizzato Elettrica
- Växla Baco
- Växla SEADA
- Växla Doepke
- Växla Comet
- Växla IPGARD
- Växla CSL
- Växla Setti+
- Växla PureLink
Nyaste Växla Manualer
27 Oktober 2024
27 Oktober 2024
22 Oktober 2024
22 Oktober 2024
22 Oktober 2024
19 Oktober 2024
19 Oktober 2024
18 Oktober 2024
18 Oktober 2024
18 Oktober 2024