Jensen XDA95RB Bruksanvisning

Jensen mottagare XDA95RB

Läs nedan 📖 manual på svenska för Jensen XDA95RB (10 sidor) i kategorin mottagare. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/10
NSA1124-V01
2025
XDA91RB,92RB,94RB,95RB
XDA SERIES
Preparation
Please read entire manual before installation. Due to the technical nature
of ampliers, it is highly recommended that your amplier is installed by a
professional installer or an authorized dealer.
Before You Start
• Disconnect negative battery terminal. (consult a qualied technician for
instructions)
• Avoid installing the amplier where it would be subject to high temperatures, such
as from direct sunlight, or where it would be subject to dust, dirt or excessive
vibration.
• Use extreme caution when drilling holes to avoid damaging fuel lines or existing
vehicle wiring.
• All amplier installations require power, signal and speaker wires (not included).
• An amplier installation kit (sold separately) is highly recommended to facilitate
the installation. Consult your dealer for recommendations.
Mounting Location
• Choose a mounting location for the amplier. Suggested locations include under a
seat or in the trunk.
• The amplier can be mounted horizontal (recommended) or vertical. For optimum
performance, make sure to provide at least 1" of space around all sides. Do not
mount the amplier under carpets or where airow is restricted.
• Do not install the amplier where it may be exposed to moisture.
• The optimum mounting location varies between vehicles. Remember to test all
amplier functions before completing the nal mounting procedure.
TYPICAL
MOUNTING
METHOD
1
XDA SERIES
18
0
XDA SERIES
NOTE:
Be sure to follow specic instructions included with your amplier installation kit
(not included with this amplier). The information below should be used as a general
guideline only.
Power Wire (+12V)
• Disconnect negative battery terminal before proceeding. Consult a qualied
technician for instructions if you are unsure.
• Plan wire routing before cutting any wires to length. Begin by routing the power
+12V wire from the battery to the amplier location. Use a grommet when running
wires through the rewall or metal openings. Avoid running the power wire near
existing vehicle wiring to prevent induced noise from entering the audio system.
• Use extreme caution when drilling holes to avoid damaging fuel lines or existing
vehicle wiring.
• The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s
electrical system.
Ground Wire (GND)
• The amplier ground wire should be as short as possible (no more than 36" or
1 meter). Choose a clean unpainted section of metal or the vehicle chassis when
attaching the ground connection. Be sure to clean the area of any dirt or grease.
Remote Turn-on Wire (REM)
• The remote turn-on wire connects to the head unit's amplier turn-on lead or
power antenna output.
Speaker Wires
• Choose adequate gauge speaker wire depending on your exact amplier/speaker
combination. Be sure to observe polarity when connecting.
• Do not ground any speaker wires or connect any speaker wires together.
Input Signal
• The amplier's input signal connects to the head unit's low level (RCA) or high level
(speaker wire) outputs.
• Low level input signals deliver the best performance. If unavailable, use the high
level inputs - when interfacing with factory head unit for instance.
Power / Protect Indicators
• Colored LED indicators illuminate from the plastic power terminal.
• The blue LED illuminates during normal operation (POWER) and the red
LED indicator is visible when the amplier detects a fault ( PROTECT).
CAUTION
• Do not use both low and high level inputs at the same time. Connect only one or the
other.
• Keep low level inputs away from any power wires to avoid engine noise.
• Never run any wires underneath or outside the vehicle.
Connection Descriptions
2
Notes
XDA SERIES
17

Produktspecifikationer

Varumärke: Jensen
Kategori: mottagare
Modell: XDA95RB

Behöver du hjälp?

Om du behöver hjälp med Jensen XDA95RB ställ en fråga nedan och andra användare kommer att svara dig


mottagare Jensen Manualer

Jensen

Jensen MPR210RGB Bruksanvisning

7 Januari 2025
Jensen

Jensen XDA95RB Bruksanvisning

11 December 2024
Jensen

Jensen CAR710-4BC Bruksanvisning

26 Oktober 2024
Jensen

Jensen VX3518 Bruksanvisning

2 Oktober 2024
Jensen

Jensen CAR710-4 Bruksanvisning

26 September 2024
Jensen

Jensen MPQ914 Bruksanvisning

21 September 2024
Jensen

Jensen CAR1013 Bruksanvisning

17 September 2024
Jensen

Jensen CAR813 Bruksanvisning

17 September 2024
Jensen

Jensen CAR723W Bruksanvisning

17 September 2024
Jensen

Jensen MPR210 Bruksanvisning

12 September 2024

mottagare Manualer

Nyaste mottagare Manualer

Alto

Alto D1 Bruksanvisning

16 Januari 2025
Alto

Alto MC700.4 Bruksanvisning

16 Januari 2025
Alto

Alto MC250.4 Bruksanvisning

16 Januari 2025
Alto

Alto MC250.8 Bruksanvisning

16 Januari 2025
Alto

Alto D4 Bruksanvisning

16 Januari 2025
Alto

Alto D3 Bruksanvisning

16 Januari 2025
Alto

Alto MC500.4 Bruksanvisning

16 Januari 2025
S.M.S.L

S.M.S.L PA200 Bruksanvisning

15 Januari 2025
Peavey

Peavey CKd 608 Bruksanvisning

15 Januari 2025
Wavtech

Wavtech link700.4plus Bruksanvisning

14 Januari 2025