JETI J-MSW-100-MS Bruksanvisning

JETI Radiostyrda leksaker J-MSW-100-MS

Läs nedan 📖 manual på svenska för JETI J-MSW-100-MS (8 sidor) i kategorin Radiostyrda leksaker. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/8
U
SER
M
ANUAL
ELECTRONIC
SWITCH
Main Switch
By JETI model s.r.o 25. 9. 2014
User Manual: Electronic switch Main Switch
-2-
1. Introduction
Main Switch is an electronic switch designed primarily for switching of the main power supply for an RC model. It adds
an element of safety when handling the model, without the need to physically disconnect the model´s batteries. A big
advantage of electronic switches in comparison to mechanical switches is, in general, their higher reliability as far as
vibration resistance is concerned. Another advantage of the electronic switch is its ability to withstand an unlimited number
of switching cycles. Electronic switches have no moving parts like contacts which would be worn out during the switching
processes, therefore their longevity is extremely high. Moreover, they are not prone to spontaneous and unexpected false
tripping with known disastrous effects. Last but not least, electronic switches offer a much lower inherent transient
resistance in comparison to mechanical switches. The Main Switch prevents the connectors from sparking when
connecting the batteries, thus it can also replace Anti Spark plugs.
The Main Switch is shipped with a magnetic switch. The magnetic switch instructions can be found on the
manufacturer´s website. It is also possible to use the optional RC Switch instead of the magnetic switch.
The Main Switch is primarily designed for switching the main power supply of the RC models, but can also be used in
applications where switching a DC power supply is needed.
2. Connection
The power supply is connected to the Main Switch using two input wires with cross sections of 6 or 8mm
2. The output
voltage is available at two cables with cross sections of 6 or 8mm2. The output three-wire cable with the JR connector is
used for telemetry data transmission. The output three-pin connector is used to connect the supplied magnetic switch or
the RC Switch.
The Main Switch connects and disconnects the negative pole - , the + pole is always connected and is never
disconnected!
Fig. 1: Connection of input and output cables
Be sure to connect the power supply wires correctly; always connect the red cable to the + pole of the
accumulator, the black cable to the – pole of the accumulator. Pay attention when connecting outputs and inputs,
they must not be swapped. Failure to follow these requirements may result in irreversible damage to the Main
Switch!! Only connect batteries to the input IN and connect speed controllers, receivers, servos etc. to the output
OUT.
User Manual: Electronic switch Main Switch
-3-
Before switching on the electronic switch you should always connect the batteries first and only afterwards
switch on the system using the magnetic switch or the RC Switch. Follow this rule also for the switching off
procedure. Switch the system off first and disconnect the batteries only afterwards.
2.1 Connection of the Main Switch
The Main Switch measures the battery current and the voltage. If you do not need to get telemetry information from the
Main Switch, you do not have to connect the Ext. output. If you DO want to display then the telemetry the Main Switch Ext.
output must be connected to the Ext. Duplex receiver input. This also powers the measurement part of the Main Switch.
Fig. 2: Block diagram of the Main Switch
The ground (-) of the Main Switch Ext. is isolated. Do not connect the ground (-) of Magnetic switch / RC Switch to the
output ground of the Main Switch (-OUT).
2.2 Charging of the battery
The battery can be charged while connected to the Main Switch (be sure that the Main Switch is in the off state – the
green LED is off), but do not attempt to disconnect the battery while charging. The charging voltage is to be connected
directly to the battery (alternatively, to the battery through the switch input), but never connect charging voltage to the
switch output!! If it becomes necessary to disconnect the battery, disconnect the charging voltage first!! Failure to follow
these basic rules can destroy the Main Switch!!

Produktspecifikationer

Varumärke: JETI
Kategori: Radiostyrda leksaker
Modell: J-MSW-100-MS

Behöver du hjälp?

Om du behöver hjälp med JETI J-MSW-100-MS ställ en fråga nedan och andra användare kommer att svara dig


Radiostyrda leksaker JETI Manualer

JETI

JETI TD1609S Bruksanvisning

10 September 2024
JETI

JETI JDEX-RR7 Bruksanvisning

10 September 2024
JETI

JETI JEX-MF2G-800 Bruksanvisning

10 September 2024
JETI

JETI Central Box 220 Bruksanvisning

10 September 2024
JETI

JETI MEZON 75 opto (RPM) Bruksanvisning

9 September 2024
JETI

JETI Central Box 210 Bruksanvisning

9 September 2024
JETI

JETI Duplex Rsat 2 EX Bruksanvisning

9 September 2024
JETI

JETI JM-090-L Bruksanvisning

9 September 2024
JETI

JETI TD0905L Bruksanvisning

9 September 2024
JETI

JETI AddCAP 1640 Bruksanvisning

9 September 2024

Radiostyrda leksaker Manualer

Nyaste Radiostyrda leksaker Manualer

Traxxas

Traxxas Rally VXL Bruksanvisning

8 Januari 2025
Hobbywing

Hobbywing XeRun XR10 PRO DR Bruksanvisning

4 Januari 2025
Spektrum

Spektrum DX5 Pro Bruksanvisning

30 December 2025
Sharper Image

Sharper Image Virtual Pong Bruksanvisning

20 December 2024
Sharper Image

Sharper Image RC Gravity Rover Bruksanvisning

20 December 2024
Sharper Image

Sharper Image Pocket Video Drone Bruksanvisning

20 December 2024
Sharper Image

Sharper Image Shadow Fighter Bruksanvisning

20 December 2024
Sharper Image

Sharper Image Space Blaster Shooting Game Bruksanvisning

20 December 2024
Axial

Axial Wraith Spawn Bruksanvisning

16 December 2024
Reely

Reely JoVage 4x4 V2 Bruksanvisning

12 December 2024