JL Audio C1-100ct Bruksanvisning

JL Audio högtalare C1-100ct

Läs nedan 📖 manual på svenska för JL Audio C1-100ct (8 sidor) i kategorin högtalare. Denna guide var användbar för 18 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/8
OWNERS MANUAL
Thank you for choosing JL Audio loudspeakers for
your automotive sound system.
We strongly recommend that you have your new loudspeakers installed by
an authorized JL Audio dealer. Your authorized dealer has the training,
expertise and installation equipment to ensure
optimum performance of these loudspeakers in your vehicle.
If you decide to install the loudspeakers yourself, please read this manual
thoroughly to familiarize yourself with their installation
requirements and setup procedures.
Should you have any questions regarding the instructions in this manual,
please contact your authorized JL Audio dealer for assistance, or call the
JL Audio Technical Support Department at (954) 443-1100
during business hours (USA - Eastern Time Zone).
1-inch (25 mm) Component Tweeters
2 | JL Audio - C1-100ct Owners Manual
Tweeter Fixture Physical Dimensions Flush-Mount Surface-Mount
Fixture Outer Diameter (A) 1.97 in / 50 mm 2.01 in / 51 mm
Fixture Mounting Hole Diameter (B) 1.75 in / 45 mm N/A
Fixture Mounting Depth (C) 0.40 in / 10 mm N/A
Tweeter Frontal Protrusion (D) 0.32 in / 8 mm 0.87 in / 22 mm
B
A
C
Crossover Network Physical Dimensions
Width (A) 1.96 in / 50 mm
Height (B) 0.90 in / 23 mm
Depth (C) 1.34 in / 34 mm
B
A
D
C
A
D
Due to ongoing product development, all specifications are subject to change without notice.
3
C1-100ct SPECIFICATIONS
Continuous Power Handling: 60 Watts
Recommended Amp Power: 20-60 Watts / ch. (RMS)
Efficiency: 91.5 dB @ 1W / 1m | 97.5 dB @ 1W / 0.5m
Sensitivity: 94.5 dB @ 2.83V / 1m
Nominal Impedance: 4 ohm
Frequency Response: 3.6 kHz - 22 KHz ± 3 dB
Tweeter:
Edge-driven, silk-suspended aluminum dome
1.0 in. (25 mm) diameter diaphragm / voice coil
Ferrofluid cooling / damping
Neodymium Magnet
Crossover:
2nd order, high-pass filter with inductor and
electrolytic capacitor
Included Components and Parts:
Two (2) C1-100ct 1.0-inch (25 mm) tweeters
Two (2) surface-mount tweeter fixtures
Two (2) C1-100cthp in-line, high-pass filters on
4 ft. (1.2 m) wire harnesses
Two (2) metal spring clips (for tweeter flush-mounting)
Four (4) #6 x .625-inch (22 mm) sheet metal screws
Two (2) 10mm stud bolts with fixed M4 nut
Two (2) 25mm stud bolts with fixed M4 nut
Two (2) M5 nuts
GETTING STARTED
Turn off the audio system. It is also
advisable to disconnect the negative
() terminal of your vehicle’s battery
whenever performing installation work.
Before cutting, drilling or inserting any screw,
check clearances on both sides of the planned
mounting surface. Also check for any potential
obstacles, such as window tracks and motors,
wiring harnesses, etc. Check both sides of the
vehicle, many vehicles are not symmetrical!
Always wear protective eyewear.

Produktspecifikationer

Varumärke: JL Audio
Kategori: högtalare
Modell: C1-100ct

Behöver du hjälp?

Om du behöver hjälp med JL Audio C1-100ct ställ en fråga nedan och andra användare kommer att svara dig




högtalare JL Audio Manualer

högtalare Manualer

Nyaste högtalare Manualer