JL Audio M1000/5v2 Bruksanvisning

JL Audio mottagare M1000/5v2

Läs nedan 📖 manual på svenska för JL Audio M1000/5v2 (11 sidor) i kategorin mottagare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/11
OWNER’S MANUAL
Remo te
Level
Mod e
Tu rn-On
Mod e
All | Sub Ch.
Input Mod e
2 Ch. | 4 Ch. | 6 Ch.
Rem. | Oset | Signal
Input Volta ge
Low | High
CH. 3
( L) CH. 4
( R)
CH. 1
( L)
CH. 1 & 2 CH. 3 & 4 SUB CH.
CH. 2
( R)
HP Filter Mod e
Filter Freq. (Hz )
Input
Sens .
O | p1-x1 | x10
Filter Mod e
HP Filter Freq. (Hz )
Input
Sens .
O | BP | HP
LP Filter Mod e
LP Filter Freq. (Hz )
Input
Sens .
O | 12 dB | 24dB
Mon o Sub woo fe r O utput
(L )
(
R)
CH. 1
CH. 2
CH. 3
CH. 4
SUB
SUB
INP UT S ECT IO N
+12 VDC Gro und Remo te
Mar ine 5 Channe l Amplif ier wit h 2- Way / 3- Way Cro ssover
Thank you for purchasing a JL Audio amplifier for
your marine sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your vessel.
For maximum performance, we highly recommend that you have
your new amplifier installed by an authorized JL Audio dealer. Your
authorized dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly so as to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier’s operation, please contact your
authorized JL Audio dealer for assistance. If you need further assistance,
please call the JL Audio Technical Support Department
at (954) 443-1100 during business hours.
1000W 5-Channel Marine Amplier with 2-Way / 3-Way Crossover
2 | JL Audio - M1000/5v2 Owner’s Manual
Mounting the amplifier upside down is
strongly discouraged.
Safety Considerations:
Your amplifier needs to be installed in a dry,
well-ventilated environment and in a manner
which does not interfere with your vessel’s safety
equipment (air bags, seat belt systems, ABS brake
systems, etc.). You should also take the time to
securely mount the amplifier so that it does not
come loose in the event of a collision or a sudden
jolt to the vessel.
While this amplifier is specially designed
for marine applications, it is not waterproof
and it should not be mounted where it is likely
to get wet.
Stu
tC
m
a
v
t%
th
p
y
t1
ed
ty
lo
t%
co
o
am
PROTECT YOUR HEARING!
We value you as a long-term customer. For
that reason, we urge you to practice restraint in
the operation of this product so as not to damage
your hearing and that of others in your vessel.
Studies have shown that continuous exposure to
high sound pressure levels can lead to permanent
(irreparable) hearing loss. This and all other
high-power amplifiers are capable of producing
such high sound pressure levels when connected
UPBTQFBLFSTZTUFN1MFBTFMJNJUZPVSDPOUJOVPVT
exposure to high volume levels.
While driving, operate your audio system in
a manner that still allows you to hear necessary
noises to operate your vessel safely (horns, sirens,
etc.).
SERIAL NUMBER
In the event that your amplifier requires
service or is ever stolen, you will need to have
BSFDPSEPGUIFQSPEVDUTTFSJBMOVNCFS1MFBTF
take the time to enter that number in the space
provided below. The serial number can be found
on the bottom panel of the amplifier and on the
amplifier packaging.
Serial Number:
INSTALLATION APPLICATIONS
This amplifier is designed for operation in
vessels with 12 volt, negative-ground electrical
systems. Use of this product in vessels with
positive ground and/or voltages other than 12V
may result in damage to the product and will void
the warranty.
This product is not certified or approved for
use in aircraft.
%POPUBUUFNQUUPiCSJEHFwUIFPVUQVUTPGUIJT
amplifier with the outputs of a second amplifier,
including an identical one.
PLANNING YOUR INSTALLATION
It is important that you take the time to read
this manual and that you plan out your
installation carefully. The following are some
considerations that you must take into account
when planning your installation.
Cooling Efficiency Considerations:
The outer shell of your JL Audio amplifier is
designed to remove heat from the amplifier
circuitry. For optimum cooling performance, this
outer shell should be exposed to as large a volume
of air as possible. Enclosing the amplifier in a
small, poorly ventilated chamber can lead to
excessive heat build-up and degraded
performance. If an installation calls for an
enclosure around the amplifier, we recommend
that this enclosure be ventilated with the aid
of a fan. In normal applications, fan-cooling
is not necessary.
Remote
Level
Mode
Turn-On
Mode
All | Sub Ch.
Input Mode
2 Ch. | 4 Ch. | 6 Ch.
Rem. | Oset | Signal
Input Voltage
Low | High
CH. 1
(L)
CH. 1 & 2 CH. 3 & 4
CH. 2
(R)
HP Filter Mode
Filter Freq. (Hz)
Input
Sens.
O | p2-x1 | x10
Filter Mode
HP Filter Freq. (Hz
Input
Sens.
O | BP | HP
( L)
(R)
CH. 1
CH. 2
CH. 3
CH. 4
SUB
SUB
INP UT SECT ION
+12 VDC Ground Remote
Marine 5 Channel Amplifier with 2-Way / 3-Way Crossover
Status
LED
(pg. 11)
Ch. 1 & 2 Filter
Frequency
Selector
(pg. 8)
Ch. 1 & 2
Filter Mode
Selection
(pg. 8)
Ch. 1 & 2 Input
Sensitivity Control
(pg. 7)
Remote
Level Mode
Switch
(pg. 9)
Input
Mode
Switch
(pg. 7)
Input
Voltage
(pg. 7)
Ch.
Fre
S
Ch. 3 & 4
Filter Mode
Selection
(pg. 8)
Ch. 3 & 4 Input
Sensitivity Contr
(pg. 7)
Turn-On
Mode
(pg. 6)
Remote Turn-On
Connector
(pg. 6)
Chassis Ground
Connector
(pg. 5)
Channels 1 & 2
Preamp Input Jacks
(pg. 7)
Subwoofer Ch.
Preamp Input Jacks
(pg. 7)
+12 V Power
Connector
(pg. 5)
Channels 1 & 2
Speaker Outputs
(pg. 10)
Jack for
Remote Level
Control Knob
(pg. 10)
Channels 3 & 4
Preamp Input Jacks
(pg. 7)
4 | JL Audio - M1000/5v2 Owner’s Manual
POWER CONNECTIONS
Before installing the amplifier, disconnect the
negative (ground) wire from the vessel’s battery.
This will prevent accidental damage to the system,
the vessel and your body during installation.
The M1000/5v2’s i+12 VDCw and iGroundw
connections are designed to accept 4 AWG
power wire. 4 AWG is the required wire size for
this amplifier.
If you are installing the M1000/5v2 with other
amplifiers and wish to use a single main power
wire, use 2 AWG or 1/0 AWG main power wire
(depending on the overall current demands of all
the amplifiers in the system). This large power
wire should terminate into a fused distribution
block mounted as close to the amplifiers as
possible (within 12 inches / 30cm of wire length).
The fused output of the distribution block will
connect to the M1000/5v2 with 4 AWG power
wire. JL Audio ECS fused distribution blocks are
SFDPNNFOEFE9%'%#6BOE9%'%#6
Note: Smaller AWG numbers mean bigger
wire and vice-versa (1/0 AWG is the largest, 2
AWG is smaller, then 4 AWG, then 8 AWG, etc.).
To connect the power wires to the amplifier,
first back out the set screw on the top of the
terminal block, using the supplied 2.5 mm hex
wrench. Strip 1/2 inch (12 mm) of insulation from
the end of each wire and insert the bare wire into
the terminal block, seating it firmly so that no
bare wire is exposed. While holding the wire in
place, tighten the set screw firmly, taking care not
to strip the head of the screw.
Any wires run through barriers must
be protected with a high quality rubber
grommet to prevent damage to the
insulation of the wire. Failure to do so
may result in a dangerous short circuit.
6 A
ch
con
dr
AW
ma
thr
gro
a s
gro
AW
fus
FU
wi
fus
bat
po
equ
on
wi
con
run
MA
PRODUCT DESCRIPTION
The JL Audio M1000/5v2 is a five-channel,
TZTUFNBNQMJGJFSVUJMJ[JOH+-"VEJP/FY%VMUSB
high speed switching technology for its four main
DIBOOFMTBOE/FY%IJHITQFFETXJUDIJOHGPS
JUTTVCXPPGFSDIBOOFM5IF/FY%UFDIOPMPHJFT
deliver outstanding fidelity and efficiency.
The M1000/5v2 can be operated with a wide
variety of source units and system configurations.
TYPICAL INSTALLATION SEQUENCE
The following represents the sequence
for a typical amplifier installation, using an
aftermarket source unit or OEM Interface
processor (like the CleanSweep CL441dsp).
Additional steps and different procedures may
be required in some applications. If you have
any questions, please contact your authorized
JL Audio dealer for assistance.
1)%JTDPOOFDUUIFOFHBUJWFCBUUFSZQPTU
connection and secure the disconnected cable
to prevent accidental re-connection during
installation. This step is not optional.
2) Run 4 AWG power wire from the battery
location to the amplifier mounting location.
Take care to route the wire in such a way that
it will not be damaged and will not interfere
with vessel operation. Use 2 AWG or larger
power wire and a power distribution block if
additional amplifiers are being installed with
the M1000/5v2.
3) Connect power wire to the positive battery
post. Fuse the wire with an appropriate fuse
block (and connectors) within 18 inches (45
cm) wire length of the positive battery post.
This fuse is essential to protect the vessel. Do
not install the fuse until the power wire has
been securely connected to the amplifier.
44) Connect negative power wire to the
negative battery post. Use the same size
power wire as the wire connected to the
i+12VwDPOOFDUJPONJOJNVN"8(
5) Run signal cables and remote turn-on wire
from the source unit to the amplifier
mounting location.
6) Run speaker cable from the speaker systems
to the amplifier mounting location.
7) Securely mount the amplifier.
8) Connect the positive and negative power
wires to the amplifier. A fuse near the
amplifier is not necessary if the M1000/5v2 is
the only device being run from the fused main
power wire. If the fused main power wire is
shared by the M1000/5v2 and other amplifiers
or devices, fuse each amplifier/device within
12 inches (30 cm) of wire length, via a fused
distribution block or multiple individual fuse
blocks/on-board fuses.
9) Connect the remote turn-on wire
to the amplifier.
10) Connect the input cables to the amplifier.
11) Connect the speaker cables to the amplifier.
12) Carefully review the amplifier’s control
settings to make sure that they are set
according to the needs of the system.
13) Install the power wire fuse(s) (80A for a
single M1000/5v2) and reconnect the negative
battery post terminal.
14) Turn on the source unit at a low level
to double-check that the amplifier is
configured correctly. Resist the temptation
to crank it up until you have verified the
control settings.
15) Make necessary adjustments to the input
sensitivity controls to obtain the right
overall output and the desired balance
in the system. See Appendix A (page 14)
for the recommended input sensitivity
setting method.
16) Enjoy the fruits of your labor with your
favorite music.

Produktspecifikationer

Varumärke: JL Audio
Kategori: mottagare
Modell: M1000/5v2

Behöver du hjälp?

Om du behöver hjälp med JL Audio M1000/5v2 ställ en fråga nedan och andra användare kommer att svara dig


mottagare JL Audio Manualer

JL Audio

JL Audio VX600/6i Bruksanvisning

12 Oktober 2024
JL Audio

JL Audio HD Series HD600/4 Bruksanvisning

7 Oktober 2024
JL Audio

JL Audio MV400/4i Bruksanvisning

1 Oktober 2024
JL Audio

JL Audio Slash 300/4v3 Bruksanvisning

28 September 2024
JL Audio

JL Audio XDM800/8-24V Bruksanvisning

24 September 2024
JL Audio

JL Audio XDM600/6-24V Bruksanvisning

24 September 2024
JL Audio

JL Audio MV700/5i Bruksanvisning

19 September 2024
JL Audio

JL Audio MHD600/4-24V Bruksanvisning

18 September 2024
JL Audio

JL Audio MHD900/5-24V Bruksanvisning

18 September 2024
JL Audio

JL Audio M800/8-24V Bruksanvisning

18 September 2024

mottagare Manualer

Nyaste mottagare Manualer

ETON

ETON MA 1 Bruksanvisning

19 Mars 2025
Elipson

Elipson P1 Bruksanvisning

14 Mars 2025
Elipson

Elipson Stream S300 Xi Bruksanvisning

14 Mars 2025
Elipson

Elipson WIIM Mini Bruksanvisning

14 Mars 2025
Rexing

Rexing RoadMate CPStream Bruksanvisning

13 Mars 2025
KanexPro

KanexPro SP-1X16SL18G Bruksanvisning

13 Mars 2025
Marshall Electronics

Marshall Electronics VDA-108-3GS Bruksanvisning

13 Mars 2025
Rega

Rega Brio MK7 Bruksanvisning

12 Mars 2025
Mtx Audio

Mtx Audio Thunder TH2500.1 Bruksanvisning

11 Mars 2025
Mtx Audio

Mtx Audio Thunder TH1500.1 Bruksanvisning

11 Mars 2025