JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 Bruksanvisning

JL Audio Inte kategoriserad Stealthbox SB-F-SUPRCNSL/10W3v3

Läs nedan 📖 manual på svenska för JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

➔

Stealthbox®

I N S T A L L A T I O N G U I D E

SB- F - S U P R C N S L / 1 0 W 3 V2 , J L AU D I O , I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 4 9 R e v i s io n 8 / 4 / 2 0 0 5 Pag e 1

for the

SB-F-SUPRCNSL/10W3v2

(‘98-Up Ford SuperDuty

250,350,450,550 & 650

‘00-Up Excursion)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

STEP 1:

From inside the factory console,

using a 9/16” socket, remove the four bolts

that secure the console to the vehicle. ( Two

of these bolts will be used later to secure

the Stealthbox).

STEP 2:

Remove the console from the vehi-

cle.

STEP 3:

Remove the inside section of the

console. (This will not be reinstalled).

-Two screws are located under the front tray.

-Three screws attach the hinge.

-Three screws are located on each side of the

consoles shell (six total)

After this section is removed, the console shell

will be in two parts.

STEP 4:

Using a pair of pliers, from the inside

of the console shell. Remove the ridges locat-

ed toward the front of the console.

STEP 5:

Reassemble the front and rear parts

of the console shell using the supplied hard-

ware (4 #8 x 1/2” long screws, 4 washer and

4 nuts) as shown in the picture.

STEP 6:

Turn the console shell upside down.

Position the Stealthbox inside the shell,

START

HERE

Continued on Next Page ➔

w w w . j l a u d i o . c o m

➔

STEP 7: Use the remaining mounting holes as a

drill guide.

Using a 1/8” drill bit and drill, drill a hole through

each of these guide holes, into the Stealthbox.

STEP 8: Install #8x 1/2” black pan-head screws

into the drilled holes.

➔ ➔

➔➔➔

STEP 10: Install #8 x 1/2” black pan-head screws

into the drilled holes.

Cont..

From

Page

Continued on Next Page ➔

➔

STEP 11: Using a 1/8” drill bit and drill. Drill two

holes at the hinge area using the outside holes only.

The center hole does not need to be drilled.

➔

STEP 12: Remove the screws installed in STEP 8

and STEP 10. Separate the console shell from the

Stealthbox.

STEP 13: Attach the OEM’s console lid to the

shell. Use one of the OEM’s screws and supplied

speed-clip to the center hole of the hinge.

STEP 9: Turn the console right-side-up with the

Stealthbox attached.

Using the holes on the top of the console shell as

guides, use a 1/8” drill bit and drill to drill holes

through each of these guide holes and into the

Stealthbox.

SB- F - S U P R C N S L / 1 0 W 3 V2 , J L AU D I O , I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 4 9 R e v i s io n 8 / 4 / 2 0 0 5 Pag e 2

w w w . j l a u d i o . c o m

STEP 14: Place the Stealthbox in the vehicle. Using

a pair of OEM bolts, from STEP 1. Loosely secure

the rear foot bracket to the floor, do not tighten.

STEP 15: Remove the paper backing on the sup-

plied sheet wax squares.

With the Stealthbox in place, lift the front of the

Stealthbox and position both supplied sheet wax

squares onto the carpet and lined up with the front

foot bracket of the Stealthbox, lower the console

down.

STEP 16: Using one of the supplied 3/8”x1-1/2”

bolts, place the bolt through each hole of the front

foot bracket (one at a time). Press down on the bolt,

too leave impressions on the sheet wax squares.

STEP 17: Remove the two OEM bolts from STEP

14. Remove the Stealthbox from the vehicle.

➔ ➔

➔ ➔ ➔

VEHICLE SHEET METAL

METAL BRACE PLATE

FLAT WASHER

HEX NUT

FRONT MOUNTING BRACKET

OF BRACKET

LOCK WASHER

FLAT WASHER

BOLT

STEP 19: Run speaker wire to the Stealthbox’s

location. Make sure the speaker wire is going to be

accessible at the rear of the Stealthbox.

*At this time, double check for proper oper-

ation of woofer*.

Cont..

From

Page

Continued on Next Page ➔

➔

STEP 18: With a 1/8” drill bit and drill, drill a pilot

hole.

With a 1/2” drill bit and drill, drill a hole through each

of the two locations.

*Caution: Check under the vehicle for any

loose brake lines, fuel lines, transfer case or

other hazards before drilling.Always wear

eye protection when drilling. *

➔

STEP 22: A second person is needed to help out in this

step.

Place a supplied flat washer onto each supplied 3/8”x1-1/2”

bolt. Place each bolt assembly through the front bracket of

the Stealthbox and the drilled holes from STEP 18.

From under the vehicle, place the supplied metal brace plate,

flat washer, lock washer and nut onto each bolt assembly.

With a second person inside the vehicle securing the bolt

head with an open-end wrench.Tighten the nut onto the

bolt assembly.

STEP 21: Replace the OEM bolts back to

the rear foot bracket. Hand-tighten the rear

bolts.

SB- F - S U P R C N S L / 1 0 W 3 V2 , J L AU D I O, I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 4 9 R e v i s io n 8 / 4 / 2 0 0 5 Pag e 3

w w w . j l a u d i o . c o m

STEP 25: Tighten the bolts at the rear of the

Stealthbox, inside the vehicle.

STEP 26: Connect the speaker wire to

the terminal cup on the Stealthbox.

STEP 27: Place the pair of supplied alu-

minum spacers over the two holes that are

located at the upper rear of the Stealthbox,

From STEP 11.

STEP 20: Position the Stealthbox back into place.

Produktspecifikationer

Varumärke:	JL Audio
Kategori:	Inte kategoriserad
Modell:	Stealthbox SB-F-SUPRCNSL/10W3v3

Behöver du hjälp?

Om du behöver hjälp med JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad JL Audio Manualer

JL Audio M6-10FES Bruksanvisning

17 Oktober 2024

JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Bruksanvisning

4 Oktober 2024

JL Audio MBT-RX Bruksanvisning

3 Oktober 2024

JL Audio Stealthbox SBA-J-JLU-UAR Bruksanvisning

30 September 2024

JL Audio Stealthbox SB-POL-RZG3/10TW3 Bruksanvisning

29 September 2024

JL Audio MediaMaster 55-HR Bruksanvisning

25 September 2024

JL Audio MediaMaster 55 Bruksanvisning

25 September 2024

JL Audio MBT-RXv2 Bruksanvisning

24 September 2024

JL Audio MBT-CRXv3 Bruksanvisning

24 September 2024

JL Audio Stealthbox SBX-F-MAVG1/10TW1 Bruksanvisning

23 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024