Joy-it RB-RGBLED01 Bruksanvisning

Läs nedan 📖 manual på svenska för Joy-it RB-RGBLED01 (8 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/8
RB
RB
RB
RBRB-
-
-
--RGBLED01
RGBLED01
RGBLED01
RGBLED01RGBLED01
RGB LED Module for Raspberry PI-
1. GENE
1. GENE
1. GENE
1. GENE1. GENERAL INFORMAT
RAL INFORMAT
RAL INFORMAT
RAL INFORMATRAL INFORMATION
ION
ION
IONION
Dear customer, thank you very much for choosing our product.
In following, we will introduce you to what to observe while start-
ing up and using this product.
Should you encounter any unexpected problems during use,
please do not hesitate to contact us.
2. USAGE WITH A RASPBERRY PI
2. USAGE WITH A RASPBERRY PI
2. USAGE WITH A RASPBERRY PI
2. USAGE WITH A RASPBERRY PI2. USAGE WITH A RASPBERRY PI
2.1 Installation of the Soware
If you already use the most current Raspbian System on your Rasp-
berry Pi, you can simply skip this step and proceed with Step 1.2.
Please use the program to install the current Win32 Disk Imager
Raspbian image on your SD card. You will find the download of it, if
you follow this link.
Choose your device by browsing through your files and save the file
with Write.
2.2 Connecting the module
Attach the module onto the pins 1 to 26 of your Raspberry Pi, like
shown in the picture below.
Make sure, that the RGB LED of the module is showing towards the -
inside.
2. USE WITH A RASPBERRY PI
2. USE WITH A RASPBERRY PI
2. USE WITH A RASPBERRY PI
2. USE WITH A RASPBERRY PI2. USE WITH A RASPBERRY PI
2.3 Preparing the module
Once you have started the system, open the terminal console and
execute the following commands:
sudo apt get update-
sudo apt get install gcc make build essential python- - -
dev git scons swig
sudo nano /etc/modprobe.d/snd- blacklist.conf
Now open the configuration file with :
sudo nano /boot/config.txt
We install the required packages and confirm them with the
Y
Y
Y
YY
key:
For use, the audio output must be deactivated. For this purpo-
se we process the files responsible for this. We open it with the
command:
backlist snd_bcm2835
Add the following line:
Save and exit the file with the key combination:
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + XCTRL + O , ENTER , CTRL + X
Scroll down the file to the lines:
#dtparam=audio=on
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
Now comment out the bottom line with a hashtag # so that it
looks like this :
Save and exit the file with the key combination:
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + X CTRL + O , ENTER , CTRL + X
The Raspberry PI must be restarted with the following com-
mand:
sudo reboot

Produktspecifikationer

Varumärke: Joy-it
Kategori: Inte kategoriserad
Modell: RB-RGBLED01

Behöver du hjälp?

Om du behöver hjälp med Joy-it RB-RGBLED01 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Joy-it Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer