Jung A1561.07FKOCH Bruksanvisning

Jung Inte kategoriserad A1561.07FKOCH

Läs nedan 📖 manual på svenska för Jung A1561.07FKOCH (7 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/7

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.: ..1561.07FKO..

Operating Instructions

Radio-control pushbutton and pilot lamp

1. Function

The radio-contol pushbutton permits radio-controlled or manual switching

and dimming of lamps.The starting brightness can be stored in the device

as memory brightness. The pushbutton with radio-control receiver is

plugged onto one of the following inserts:

 Universal touch dimmer 1254 UDE

 Standard touch dimmer 1225 SDE

 Relay insert single-channel 1201 URE

 Relay insert two-channel 1202 URE

 Tronic switching insert 1254 TSE

 LV triac switching insert 1244 NVSE

 Touch control unit 1240 STE

Relay insert with potential-free contact 1201-1 URE After reception of a

data telegram from a programmed radio-control detector and

corresponding darkness, the radio-contol pushbutton is switched on for

about 1 minute with the preset memory brightness. The radio-contol

pushbutton can be programmed to identify up to 30 radio channels.

Lightscapes

The radio-contol pushbutton can be included in up to five lightscapes

which are activated with the corresponding radio-control transmitters (e.g.

hand-held transmitter ‘Komfort’) and stored. The desired lightscape key

must be programmed beforehand into the radio-contol pushbutton.

All-ON / All-OFF

The programming of a radio channel (e.g. hand-held transmitter

‘Komfort’) always includes the simultaneous and automatic storage of the

functions of the All-ON or All-OFF key.The All-ON or All- OFF key of a

radio-control transmitter switches the load connected to the switching

actuator on or off.

Light control

In combination with a programmed radio-control presence detector, the

radio-contol pushbutton can be used for lighting control functions. For

more information, refer to the operating instructions of the radio presence

detector.

Stand: Mai-07 325 276 53

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.: ..1561.07FKO..

Important

The present instructions describe the functions of the radio-control

pushbutton without lighting control. More information on light control with

a presence detector is set out in the operating instructions for these

devices.

WARNING!

Caution: The installation and assembly of electrical equipment may

only be performed by a skilled electrician.

2. Fitting

The radio-control pushbutton can only be operated in conjunction with the

inserts listed under ‘Functions’. Connection and fitting are described in

the operating instructions of the insert.

Procedure

1. Install the selected insert (1) in a flush-mounting box (deep model

recommended), the connecting terminals of the insert pointing

downwards.

2. Plug the radio-control pushbutton (2) together with frame (3) onto

the insert while the mains voltage is disconnected.

L The distance from electrical appliances (e.g. microwave oven, hi-fi and

TV sets) must be at least 0.5 m.

L To prevent saturation of the radio receiver (actuator), the radiocontrol

pushbutton must be at least 1 m away from the nearest transmitter.

Learning a Radio Transmitter

During programming of a transmitter, the sensitivity of a radiocontrol

receiver is reduced to a range of approx. 5 m. The distance between the

radio-control pushbutton and the transmitter to be programmed should be

between 0.5 m and 5 m.

Procedure

1. Switch off the load connected to the radio-control pushbutton by a brief

depression (< 0,4 s) of any of the two pushbutton rockers.

2. Depress both rockers of the radio-control pushbutton at the same time

for abt. 4 seconds (fig. B: double-sided operation) to switch over to the

programming mode. The LED blinks for abt. 1 min (Fig. C). The radio

pushbutton is then in the programming mode.

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.: ..1561.07FKO..

> 4 s

Prog

1 min t

3. Send a radio telegram from the selected transmitter (fig. D); see

„Radio-control transmitter“ operating instructions:

ABC

123

Programming a channel

Depress the channel key for more than 1 second.

Programming a lightscape key

Depress the lightscape key for more than 3 seconds.

Programming a detector

Remove the battery for about 2 minutes from the detector. Put the the

battery back in place and make a movement inside the detection range of

the detector within the next 10 minutes.

Programming a presence detector

Remove the battery(ies) for about 2 minutes from the transmitter. After

putting the battery back in place, the device starts transmitting

programming telegrams for about 30 s.

L It is not possible to program a combination consisting of presence-

control detector and detector.

4. The radio pushbutton confirms the storage by switching on the

LED permanently

Prog

1 min t

5. The programming mode ends automatically after about 1 minute or

can be terminated by a short depression of the programming key. The

radio-control pushbutton is then again in the normal operating mode.

L When all 30 memories are occupied, it is necessary to delete an

already stored transmitter before a new one can be programmed.

Produktspecifikationer

Varumärke:	Jung
Kategori:	Inte kategoriserad
Modell:	A1561.07FKOCH
Färg på produkten:	Zwart
Bredd:	749.3 mm
Djup:	260.4 mm
Höjd:	1168.4 mm
Förpackningens vikt:	11910 g
Monteringsmetod:	Plafond
Maximal viktkapacitet:	79.38 kg
Rotationsvinkel:	110 °
Antal skärmar som stöds:	1
Tiltvinkelområde:	-5 - 15 °
Maximal skärmstorlek:	70 "
Minsta skärmstorlek:	37 "