Jung ASLS1280-1 Bruksanvisning

Jung Växla ASLS1280-1

Läs nedan 📖 manual på svenska för Jung ASLS1280-1 (13 sidor) i kategorin Växla. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/13

Universal automatic switch 180° 2.20 m

Light Management

Universal automatic switch 180° 2.20 m

Art.-No.: AS..1280-1..

Operating instructions

1 Safety instructions

Electrical equipment may only be installed and fitted by electrically skilled persons.

Failure to observe the instructions may cause damage to the device and result in fire and

other hazards.

Danger of electric shock. Always disconnect before carrying out work on the devise or

load. At the same time, take into account all circuit breakers that supply dangerous

voltage to the device or load.

Danger of electric shock. Device is not suitable for disconnection from supply voltage.

The load is not electrically isolated from the mains even when the device is switched off.

Do not press on the sensor window. Device can be damaged.

Disconnect before mounting the cover, malfunction possible.

Keep button cells out of reach of children! If button cells are swallowed, get medical help

immediately.

Risk of explosion! Do not throw batteries into fire.

Risk of explosion! Do not recharge batteries.

The device is not suitable for use as a burglar alarm or other alarm.

These instructions are an integral part of the product, and must remain with the end

customer.

2 Device components

Figure 1

(1) Insert

(2) Frame

(3) Motion detector

(4) LED red

(5) Button Off/Auto

(6) LED yellow

1/13

32576803

J:0082576803 03.05.2011

(7) Button On/Auto

(8) Lens

3 Function

Intended use

- Automatic switching of light, depending on heat motion and ambient brightness

- Operation with concealed insert for dimming, switching or extension insert, 3-wire

- Mounting indoors or outdoors on concealed insert

Product characteristics

- Adjustable functions with IR remote control

- Extension of the detection area in combination with the 3-wire extension insert

- Operation with IR remote control, buttons on the motion sensor, 2-wire extension or

installation button

- Teach function for adjustment of the brightness threshold in combination with IR remote

control

- Switch-on brightness permanently storable, with dimming insert

- Dimmable light with dim insert

- Dimming function, with dimming insert

- Short time operation, e.g. for controlling acoustic alarms, with switching insert

- Display LED

- Creep zone protection

- Presence simulation

- Night light function

- Run-on time limit

Automatic operation

The motion detector detects heat motions of people, animals and objects.

- The light is switched on if a person enters the detection area and the brightness is below

the set threshold.

The run-on time restarts with each detected motion.

- The light is switched off if no motion is detected in the detection area and the run-on time

has elapsed or the run-on time limit is reached.

To avoid any light swings caused by a cooling illuminant, the motion detector does not evaluate

any motion signals for a brief lockout time after switching off. The motion detector adjusts itself

to the ambient conditions to keep the time as short as possible.

The day/night switchover takes place after a delay of 30 seconds. Switching over is thus

prevented by briefly illuminating or shadowing to the day/night operation.

Short time operation

The motion detector is combined with a switching insert. Depending on motion and ambient

brightness a short pulse is triggered The pulse is cyclically repeated as long as motions are

detected.

Dimming phase

If the motion detector is combined with a dimming insert, the light is dimmed to minimum

brightness after the run-on time and then switched off The time from the start of dimming until

switching off is approx. 30 seconds. If a motion is detected during the dimming phase, the

motion detector switches the light to the saved switch-on brightness again.

Run-on time limit

The light is switched off after 90 minutes at the latest even if there is constant motion in the

detection area. The light is only switched on again if the brightness drops below the threshold

and motions are detected.

i Exception: After switching off the continuous On or On for 2 hours operating modes, the

lighting is switched off after 30 minutes at the latest.

2/13

32576803

J:0082576803 03.05.2011

Light Management

Universal automatic switch 180° 2.20 m

Presence simulation

In automatic operation, the motion detector continuously saves times for which the lighting was

switched on or off. A maximum of 120 switching operations are saved over a period of 7 days. If

more switching operations take place, the oldest ones are overwritten respectively. If the

presence simulation is activated, the motion detector performs the saved switching operations.

If not enough switching operations are saved, random switching operations are performed.

Detected motions prolong the run-on time or the light is switched on depending on brightness.

Times are not saved.

i A motion detector on a 3-wire extension insert does not save any times.

i With the HVAC insert, the function is only performed for channel 1.

Night light function

The motion detector is combined with a dimming insert. If the night light function is activated,

the light is switched between two brightness values. In idle state, the brightness is 20 % of the

maximum brightness. If motions are detected, the light is switched to the switch-on brightness.

i If the Off for 2 hours function or continuous Off function is active, the light is switched off.

Behaviour after a mains failure

- Less than 0.2 seconds: the old switching position is restored after mains return.

- 0.2 seconds until approx. 2 seconds: The light is switched on for the run-on time after

mains return.

- Longer than 2 seconds: The motion detector goes through a self-test for approx.

40 seconds after mains return. The light is first switched on. After approx. 10 seconds, the

light is switched off. After the end of the self-test, the light is switched on for the duration of

the run-on time. The motion detector is in automatic operation.

4 Operation on a main unit

Display LED

Behind the lens (8) are a red (4) and a yellow (6) LED (Figure 1) for indicating different

operating states.

Red LED Yellow LED Signalling

off on Light switched on continuously

on off Light switched off continuously

flashed in rhythm of the

detection

off Detection of motion, for

outdoor use

flashes off Receipt of IR signals

off on for 1 second IR signal detected

The operation and necessary settings are carried out using the IR remote control. Some

settings are carried out one time during the commissioning and should only be changed if the

ambient conditions change.

i Switching on and dimming can also be carried out via 2-wire extension inserts. Switching

on is also possible with an installation button.

Function buttons IR remote control

Button Function

¿ Pressing for less than 0.4 seconds Continuous on

¿ Pressing for longer than 0.4 seconds Only dimming inserts: Dimming until maximum

brightness

À Automatic operation

Á Pressing for less than 0.4 seconds Continuous off

3/13

32576803

J:0082576803 03.05.2011

Light Management

Universal automatic switch 180° 2.20 m

Produktspecifikationer

Varumärke:	Jung
Kategori:	Växla
Modell:	ASLS1280-1
Enhetsplacering:	Aanrecht
Innehåll (inuti):	31 l
Typ av operation:	Knoppen
Magnetronkraft:	1000 W
Power grill:	1200 W
Färg på produkten:	Zwart
Antal effektnivåer:	8
Skivbordsstorlek:	360 mm
Nettoskatt:	2200 W
Uppvärmningsfunktion:	Ja
Grill:	Ja
Barnlås:	Ja
Integrerad klocka:	Ja
Avfrostningsfunktion:	Ja
Strömförsörjning:	50 Hz, 230 V
Innermått (B x D x H):	395 x 370 x 210 mm
Konvektion:	Ja
Mått (B x D x H):	490 x 541 x 380 mm