Jung DAW360 Bruksanvisning

Jung Växla DAW360

Läs nedan 📖 manual på svenska för Jung DAW360 (8 sidor) i kategorin Växla. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/8
Ceiling automatic switch
Light Management
Ceiling automatic switch
Art.-No.: DAW 360 WW
Ceiling automatic switch
Art.-No.: DAW 360 AL
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Danger of electric shock. Always disconnect before carrying out work on the devise or
load. At the same time, take into account all circuit breakers that supply dangerous
voltage to the device or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
The load is not electrically isolated from the mains even when the device is switched off.
Do not press on the sensor window. Device can be damaged.
The device is not suitable for use as a burglar alarm or other alarm.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1
(1) Flush-mounted insert
(2) Motion detector cover
(3) Adjuster sens
(4) Adjuster time
(5) Adjuster lux
(6) Brightness sensor
(7) LED display, behind the lens
(8) Lens
(9) Decor ring
(10) Push-on cover
1/8
82563813
J:0082563813 17.11.2011
3 Function
Intended use
- Automatic switching of lighting depending on the heat motion and ambient brightness.
- Operation with concealed insert for dimming, switching or extension insert, 3-wire
- Ceiling installation on flush-mounted insert
Product characteristics
- Run-on time, sensitivity and brightness threshold settable
- Test operation for checking the detection area
- Short-time operation to control signal encoders
- Dimming phase in combination with dimming insert
- Saving a switch-on brightness with dimming inserts
- Dimming lights with dimming inserts
- Manual switch-on possible via extension insert, 2-wire, or installation button
- 78 lens segments in 5 recording levels
- Extension of the detection area in combination with the 3-wire extension insert
- Detection area can be limited using push-on cover
Automatic operation
The controller detects heat motions of people, animals and objects.
- The light is switched on if a person enters the monitored detection area and the brightness
is below the set threshold.
- The light is switched off if no more movement is detected in the detection area and the
follow-up time has elapsed.
Dimming phase with dimming insert
If the motion detector cover is fitted on a dimming insert, then when the run-on time elapses the
lighting is dimmed to minimum brightness and then switched off. The time from the start of
dimming to switching-off is always approx. 30 s. If a motion is detected during the dimming
phase, the motion detector switches the lighting to the stored switch-on brightness again.
Behaviour in case of a mains failure
- Less than 0.2 seconds: the old switching position is restored after mains return.
- 0.2 seconds to approx. 2 seconds: when the power returns, the lighting is switched on
again for the run-on time. Each detected movement restarts the run-on time again.
- Longer than 2 seconds: when the power returns, the motion detector carries out a brief
calibration process. Then the lighting remains switched on for the run-on time. Each
detected movement restarts the run-on time again.
LED display (7)
Main device Extension
LED lights up during the calibration process. LED lights up during the calibration process.
LED lights up when a motion is detected if the
lighting is switched off and the brightness is
not below the brightness threshold.
LED lights up when a motion is detected.
4 Operation
Switching on the light
A 2-wire extension or an installation button, NO contact is connected.
o Press extension or installation button.
Light is switched on independently of the brightness, with a dimming insert to switch-on
brightness. Automatic mode is active.
i After manual switch-on the run-on time is at least 2 minutes.
i Manual switch-on is not possible.
2/8
82563813
J:0082563813 17.11.2011
Light Management
Ceiling automatic switch
Dimming light with dimming insert
The light can be dimmed using a 2-wire extension. The light remains at the dimmed value until
the run-on time has elapsed.
o Press 2-wire insert at top or bottom until the desired brightness is reached.
i An installation button cannot be used for dimming.
Saving a switch-on brightness with dimming insert
A 2-wire extension can be used to save any desired switch-on brightness. In the state as
supplied the switch-on brightness is set to maximum.
The saved switch-on brightness is retained in the event of a power failure.
o Set the required brightness.
o Press 2-wire extension for longer than 3 seconds over entire surface.
Switch-on brightness is saved. For confirmation the lighting switches off briefly and then on
again to the saved switch-on brightness.
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the
corresponding circuit breakers. Cover up live parts in the working environment.
Selecting the installation location
Figure 2: Sensor window and detection area
The motion detector has a detection area of 360° (figure 2). The diameter of the detection area
depends on the installation height and the direction of motions of persons in the detection area
(figure 3). At an installation height of 3 m the maximum diameter on the floor is approx. 12 to 20
m.
3/8
82563813
J:0082563813 17.11.2011
Light Management
Ceiling automatic switch

Produktspecifikationer

Varumärke: Jung
Kategori: Växla
Modell: DAW360

Behöver du hjälp?

Om du behöver hjälp med Jung DAW360 ställ en fråga nedan och andra användare kommer att svara dig


Växla Jung Manualer

Jung

Jung W8180 Bruksanvisning

10 December 2024
Jung

Jung 201TE Bruksanvisning

10 December 2024
Jung

Jung BTA17102 Bruksanvisning

2 Oktober 2024
Jung

Jung ASLS1280-1 Bruksanvisning

20 September 2024
Jung

Jung SL1180 Bruksanvisning

17 September 2024
Jung

Jung AS5544.03VWW Bruksanvisning

17 September 2024
Jung

Jung ES5201DTU Bruksanvisning

17 September 2024
Jung

Jung SL1180-1 Bruksanvisning

17 September 2024
Jung

Jung CD5024WW Bruksanvisning

16 September 2024
Jung

Jung BTLC17102P Bruksanvisning

15 September 2024

Växla Manualer

Nyaste Växla Manualer

Ebara

Ebara ServoPress LP Bruksanvisning

15 Januari 2025
INOGENI

INOGENI CAM230 Bruksanvisning

14 Januari 2025
Schneider

Schneider CCT15225 Bruksanvisning

14 Januari 2025
Luxul

Luxul XMS-5248P Bruksanvisning

14 Januari 2025
Luxul

Luxul AMS-2624P Bruksanvisning

14 Januari 2025
Luxul

Luxul XGS-1005 Bruksanvisning

14 Januari 2025
Luxul

Luxul AGS-1008M Bruksanvisning

14 Januari 2025
Luxul

Luxul XMS-1208P Bruksanvisning

14 Januari 2025
Luxul

Luxul XMS-7048P Bruksanvisning

14 Januari 2025
Luxul

Luxul AMS-2600 Bruksanvisning

14 Januari 2025