Kospel HPM2.Z-16 Bruksanvisning

Kospel Värmepump HPM2.Z-16

Läs nedan 📖 manual på svenska för Kospel HPM2.Z-16 (48 sidor) i kategorin Värmepump. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/48

Installation and Operating Instructions

Master copy of the Instructions

Heat Pump

HPMI2 - 8

HPMI2 - 12

HPMI2 - 16

HPMO2 - 8 HPMO2 - 12 HPMO2 - 16/23

This device may be used by children aged 8 years and over and

by persons with reduced physical, sensory or mental abilities

or lack of experience and knowledge, if they are supervised

or have been instructed concerning the safe use of the device

and have understood the resulting hazards. Children must not

play with the device. Cleaning and maintenance of the device

may not be carried out by children without supervision.

The HPM2.Z heat pump is a hermetically

sealed unit and it contains uorinated

greenhouse gases.

WARNING

Do not use any agents to speed up the defrosting or cleaning

process other than those recommended by the Manufacturer.

Store the device in a room without any constantly operating

sources of ignition (for example: an open ame, an operating

gas device or an operating electric heater). Do not puncture

or burn the device. Note that refrigerants may be odourless.

The device is to be installed, operated and stored in a room with

adequate space and cubic area (see the table).

NOTE: The Manufacturer may provide relevant examples or additional information on refrigerant’s odour.

This equipment is intended for use by qualied or trained users

in shops, light industry and on farms, or for use at home by

those who have no specialist knowledge.

EN-115B_f.1420

1. Familiarisation with the contents of this manual will enable the device to be installed and operated correctly, ensuring its

long-lasting and reliable operation.

2. The device must be installed in compliance with national installation regulations.

3. An electrical installation that is operational and carried out in accordance with PN-IEC 60364.

4. Considering its intended use, the device may only be installed and operated in closed heating systems in accordance with

EN 12828, taking into account the relevant installation, service and operating instructions.

■ Work on the refrigeration circuit must only be carried out by authorised specialists.

■ Initial commissioning is to be carried out by an Authorised Installer or a designated authorised person.

5. Unsuitable ambient conditions may cause damage to the installation and jeopardise operational safety (avoid air pollution

by halogenated alkanes contained e.g. in paints, solvents and cleaning agents, avoid constant high air humidity e.g. due to

frequent drying of laundry).

6. The installation of the device and the electrical and plumbing work must be carried out by a specialised service company

and the instructions for the assembly and use of the product must be strictly observed.

7. All installation work must be carried out with the electricity and water supply being cut off.

8. Sparks may occur due to an electrostatic discharge, which can ignite the leaking refrigerant (R32). Touch earthed objects,

e.g. heating or water pipes, to dissipate static charges before carrying out work.

9. Hot surfaces may cause burns.

10. Direct contact with the liquid and gaseous refrigerant may cause serious damage to health.

11. The electrical installation must be tted with residual current protective devices and means to ensure that the equipment

is disconnected from the power source, where the distance between the contacts of all the poles is not less than 3mm.

12. The heat pump is a surge-sensitive device and the electrical installation must therefore include surge protection devices.

13. There is a hazard of scalding in the event of an open ame.

14. R32 is the refrigerant used; this is an air displacing, colourless, odourless gas that forms a ammable mixture with air.

Conditions for safe and reliable operation

Description of the device

The HPM2.Z heat pump is an device designed for heating/cooling a building and heating tap water.

The unit consists of two modules:

- The outdoor HPMO2 module: a compressor heat pump.

The working principle of the unit is to capture heat from the environment and to transfer it to the heating circuit in the

building. The low-temperature heat of the air is transferred through an evaporator to the heat pump system lled with

a refrigerant, which turns into a gas as it evaporates. From the evaporator, the gas is drawn in by the compressor, which

raises its temperature during its compression and directs it to the condenser. In the condenser, heat is transferred to the

refrigerant, which lls the central heating system, and the cooled liquid ows through the expansion valve and returns to the

evaporator, after which the whole process starts again. In the case of cooling, this cycle is reversed and the heat is extracted

from the building and discharged outside.

- The indoor HPMI2 module: a hydraulic module equipped with a controller for the entire system.

The working principle of the unit is based on the demand-dependent capacity control of the heat pump compressor with an

activation of the electrical auxiliary heater via the controller of the indoor module. The indoor module controller regulates

the heating output according to a pre-set heating curve. If the heat pump is not able to cover the building’s heating demand

on its own, the controller automatically activates the electrical auxiliary heater which, together with the heat pump produces

the desired heating medium temperature.

Produktspecifikationer

Varumärke:	Kospel
Kategori:	Värmepump
Modell:	HPM2.Z-16
Färg på produkten:	Wit
Vikt:	2100 g
Djup:	155 mm
Anslutningsteknik:	Bedraad
Diameter:	210 mm
Typ av strömkälla:	AC
Genomsnittlig effekt:	30 W
Rekommenderad användning:	Luidsprekerset
Ljudutgångskanaler:	1.0 kanalen
Högtalarplacering:	Inbouw in de muur/plafond
Bashögtalare:	Ja
Frekvensomfång:	100 - 18000 Hz
Känslighet:	89 dB
Diameter woofer:	5 "