Kymco Agility 125 Bruksanvisning
Läs nedan 📖 manual på svenska för Kymco Agility 125 (60 sidor) i kategorin Skotrar. Denna guide var användbar för 19 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/60
Do not remove this Owner’s Manual from the vehicle. Read this manual carefully
before operating the vehicle as it contains important safety information.
Read this manual carefully.
This Owner’s Manual contains important information on safety, operation and maintenance of your KYMCO scooter.
Any one who operates your scooter should carefully read and understand the contents of this manual before riding the scooter.
For your safety, understand and follow all of the warnings contained in this Owner’s Manual and the labels applied to your scooter.
This Owner’s Manual should be considered a permanent part of the vehicle, keep it with your scooter at all times.
ON-ROAD USE ONLY This scooter has been designed to be used on the road.
Particularly important information is called out in this manual by the following icons and notations:
WARNING
CAUTION
NO NO NO NO NOTETETETETE
The SAFETY ALERT symbol with the exclamation point in the triangle means ATTENTION!
BE ALERT! YOUR SAFETY CAN BE AFFECTED.
Failure to follow instructions associated with a WARNING symbol could result in severe injury or
death to the rider, a passenger, a bystander, or a person inspecting or repairing the scooter.
A CAUTION symbol indicates that special precautions must be taken to avoid damaging
the scooter.
The NOTE symbol indicates key information about a procedure or to clarify an operation.
California Proposition 65
WARNING
This product contains or emits chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm.
1
Manual Icon Legend .................................................... (inside of front-cover)
CA Prop 65 Warning ....................................................(inside of front-cover)
Table of Contents .......................................................................................... 1
SECTION 1 - SAFETY .................................................................2 - 6
Foreword ....................................................................................................... 2
Scooter Safety ......................................................................................... 3 - 4
Load Limits & Guidelines ............................................................................. 5
Accessories & Modifications ........................................................................ 6
SECTION 2 - CONTROLS & FEATURES ............................... 7 - 15
Locations of Parts & Controls ................................................................. 7 - 8
Keys ............................................................................................................... 9
Ignition Switch & Steering Lock ............................................................9 - 10
Right-hand Handlebar Switch .................................................................... 11
Engine-stop Switch ..................................................................................... 11
Electric Start Button .................................................................................... 11
Left-hand Handlebar Switch................................................................ 11 - 12
Headlight Dimmer Switch ........................................................................... 11
Turn Signal Switch ...................................................................................... 12
Turn Signals ................................................................................................ 12
Under-seat Storage Compartment ............................................................ 12
Helmet Posts ............................................................................................... 13
Main Stand .................................................................................................. 13
Instruments ................................................................................................. 14
Clock............................................................................................................ 14
Passenger Foot Rest .................................................................................. 15
SECTION 3 - OPERATION..................................................... 16 - 32
Break-in Recommendations ....................................................................... 16
Tire Break-in................................................................................................ 17
Pre-ride Inspection ...............................................................................18 -25
Engine Oil Inspection ................................................................................. 19
Brake Inspection ..................................................................................19 - 20
Tire Inspection ..................................................................................... 20 - 21
Fuel Level / Filler Cap ................................................................................ 22
TABLE OF CONTENTS
Steering & Handlebar Inspection ............................................................... 23
Instrument Inspection ................................................................................. 23
Horn & Lights Inspection ............................................................................ 24
Chassis Inspection ..................................................................................... 25
Starting the Engine (electric start) ...................................................... 26 - 27
Starting the Engine (kick start)................................................................... 27
Riding Your Scooter ............................................................................. 28 - 31
Parking Your Scooter ...........................................................................31 - 32
SECTION 4 - MAINTENANCE ............................................... 33 - 50
Importance of Maintenance ....................................................................... 33
Maintenance Schedule ........................................................................34 - 35
Tires............................................................................................................. 36
Tire Pressure............................................................................................... 36
Air Filter Maintenance ................................................................................ 37
Fuel System ................................................................................................ 38
Battery ..................................................................................................38 - 39
Fuse ............................................................................................................. 39
Engine Oil .................................................................................................... 40
Engine Oil Level Inspection & Change ...............................................40 - 41
Transmission Fluid Change ....................................................................... 42
Spark Plug................................................................................................... 43
Brake Fluid Level Inspection ...................................................................... 43
Brake Shoe & Pad Inspection .................................................................... 44
Cleaning Your Scooter......................................................................... 45 - 46
Storage ................................................................................................. 47 - 48
Maintenance Record ...........................................................................49 - 50
Specifications (Agility 50) ........................................................................... 51
Specifications (Agility 125) ......................................................................... 52
Emission - KYMCO Clean Air System ....................................................... 53
Emission Information & EPA Warranty ...................................................... 54
KYMCO Limited Scooter Warranty ............................................................ 55
Index ............................................................................................................ 56
Identification Numbers Record .................................. (inside of back-cover)
2
Thank you for purchasing this KYMCO Agility scooter, and welcome to the KYMCO riding family.
Please read this owner's manual carefully before riding so that you will be thoroughly familiar with the
proper operation of your scooter’s controls, its features, its capabilities, and its limitations.
To ensure a long, trouble-free life for your scooter, provide it with the proper care and maintenance as
described in this manual.
For replacement parts and accessories, you should always use genuine KYMCO products, as they have
been specially designed for your vehicle and manufactured to meet KYMCO's demanding standards.
Keep this owner's manual aboard your scooter at all times, so that you can refer to it whenever you need
information. This manual should be considered a permanent part of the scooter and should remain with the
scooter when it is sold.
All information, illustrations, photographs and specifications contained in this manual are based on the
latest product information available at the time of publication. Due to improvements or other changes, there
may be information in this manual that differs slightly from your vehicle. KYMCO reserves the right to make
product and publication changes at any time, without notice, and without incurring any obligation.
SECTION 1 -
FOREWORD & SAFETY INTRODUCTION
3
IMPORTANT SAFETY INFORMATION
Your scooter can provide you many years of service and plea-
sure if you take responsibility for your own safety and under-
stand the challenges that you can meet on the road. There is
much that you can do to protect yourself when you ride. You
will find many helpful recommendations throughout this
manual. Here are some very important safety tips:
Wear a helmet
Scooter safety equipment starts with a quality helmet. One of
the most serious injuries you can suffer in a crash is a head
injury. Always wear a properly approved helmet. You should
also wear suitable eye protection.
Make yourself easy to see
To make yourself more visible, wear bright, reflective clothing;
position yourself so other drivers can see you; signal before
turning or changing lanes; and use your horn when it will help
others notice you.
Know your limits
Ride within the boundaries of your own skill at all times. Know-
ing these limits and staying within them will help you avoid
accidents.
SCOOTER SAFETY
Keep your scooter in safe condition
For safe riding, it's important to inspect your scooter before
every ride and perform all recommended maintenance. Never
exceed load limits, and only use accessories that have been
approved by KYMCO for this scooter.
Inspect your scooter before riding
Do not forget to perform an entire safety inspection to ensure
your, and your passenger's safety, before each ride.
Be extra safety conscious on bad weather days
Riding on bad weather days, especially wet ones, requires ex-
tra caution. Braking distance can double on a rainy day. Stay
off of painted surfaces, manhole covers and greasy appearing
areas on the pavement, as they can be especially slippery. Use
extreme caution at railway crossings and on metal gratings and
bridges. Whenever your are in doubt about the road conditions,
slow down.
Modification
Modification of your scooter, or removal of original equipment
may render the vehicle unsafe or illegal. Obey all applicable
equipment regulations in your area.
4
SCOOTER SAFETY
PROTECTIVE APPAREL
For your safety, always wear an approved motorcycle or scooter
helmet, eye protection, boots, gloves, long pants, and a long-
sleeved shirt or jacket whenever you ride your scooter.
Helmets and protection
Your helmet is your most important piece of riding gear be-
cause it offers the best protection against head injuries. Your
helmet should fit your head comfortably and securely. Always
wear a face shield or goggles to protect your eyes and to aid
your vision.
Additional riding gear
In addition to a helmet and eye protection, you should also use:
•Sturdy boots with nonslip soles to help protect your
feet and ankles
•Leather gloves to keep your hands warm and help pre-
vent blisters, cuts, burns and bruises
•A motorcycle or scooter riding suit or jacket that has
been designed for comfort as well as protection. Bright
colored and reflective clothing can help make you more
noticeable in traffic. Be sure to avoid loose clothing
that can get caught on any part of your scooter.
1 Wear bright or reflective clothing. Clothes should fit
properly (not too tight or loose)
2 Always wear a helmet and eye protection
3 Wear gloves
4 Footwear should be the proper size, have low heels,
and offer ankle protection
Not wearing a helmet increases your chance of serious
injury or death in a crash.
Be sure you and your passenger always wear an approved
motorcycle helmet that fits properly. You should also wear
eye protection and other protective apparel when you ride.
11111
22
22
233
33
3
44
44
4
5
LOAD LIMITS & LOADING GUIDELINES
These general guidelines may help you decide how to add
accessories to your scooter and how to load it properly.
Load limits
These specifications are the load limits for your Agility scooter.
Overloading the scooter will affect its stability and handling.
Be sure to stay within the limits given below:
Maximum weight capacity (Includes the weight of the rider,
passenger, cargo and accessories):
Agility 50..................................................... 544 lbs (247 kg)
Agility 125................................................... 570 lbs (259 kg)
Maximum cargo weight: ................................. 22 lb (10 kg)
Under-seat compartment 5555
5 weight limit: ......11 lbs (5 kg)
Rear carrier (rack) 6 6
6 6
6 weight limit: ...................11 lbs (5 kg) Loading guidelines
Improperly loading your scooter will affect its stability and han-
dling. You should ride at reduced speeds when you are carrying a
passenger or cargo. Follow these guidelines whenever you carry
a passenger or cargo:
•Check that both tires are properly inflated
•To prevent loose items from creating a hazard, make
sure all cargo is securely tied down before you ride
•Place cargo weight as close to the center of the scooter
as possible
•Balance cargo weight evenly on both sides of the scooter
Overloading or improper loading will affect vehicle han-
dling, stability and braking, and can lead to an accident.
Never exceed the stated load capacity of your scooter.
Cargo should be properly distributed and securely at-
tached. Reduce speed when carrying cargo. Allow greater
distance for braking.
55555
66
66
6
6
ACCESSORIES & MODIFICATION
There is a large variety of accessories available to KYMCO
scooter owners. KYMCO cannot have direct control over the
quality or suitability of accessories you may wish to purchase.
The addition of unsuitable accessories to your scooter can
lead to unsafe operating conditions. It is not possible for
KYMCO to test each accessory on the market, or all of the
combinations of the available accessories; however, your
KYMCO dealer can assist you in selecting quality accessories
and then install them correctly.
Use extreme caution when selecting and installing the ac-
cessories for your scooter.
No modifications
KYMCO strongly advises you against removing any original
equipment or modifying your scooter in any way that would
change its design or operation.
Improper accessories or modifications can make your
scooter unsafe and can lead to an accident.
Never modify your scooter through the improper installa-
tion or use of accessories. All parts and accessories added
to this vehicle should be genuine KYMCO or equivalent
components designed for use on this scooter and should
be installed and used according to instruction. If you have
any questions, consult an authorized KYMCO dealer.
7
1 Left front turn signal
2 Rear brake lever
3Turn signal switch, headlight dim-
mer switch, passing light button,
horn button
4Under-seat storage compartment
5 Fuel filler
6 Tail/Brake Light
7 Left rear turn signal
8 Kick start lever
9 ESN (Engine Serial Number)
AT Main stand
NOTE: Your scooter may differ slightly in appearance from the images in this manual.
NOTE: Write your scooter’s VIN and ESN in the boxes provided in the inside, rear cover of this Owner's Manual.
SECTION 2 -
CONTROLS & FEATURES
Location of parts & controls
22
222
11
11
1
33
33
3
44
44
4
55
55
5
66
66
6
77
777
88
88
8
99
99
9
ATAT
ATATAT
8
CONTROLS & FEATURES
Location of parts & controls
NOTE: Your scooter may differ slightly in appearance from the images in this manual.
NOTE: Write your scooter’s VIN and ESN in the boxes provided in the inside, rear cover of this Owner's Manual.
1 Battery
2 Exhaust muffler
3Right rear turn signal
4Rear carrier
5 Ignition switch
6 Engine stop switch, starter motor
button
7 Instruments (Speedometer)
8 Center console
9 Right, front turn signal
AT VIN (Vehicle Identification Number)
33333
44
44
4
55
555
66666
77
777
88888
99
99
9
ATATATATAT
22
222
11
11
1
9
Keys
Your Agility scooter is supplied with two identical ignition switch
keys. The ignition key operates the ignition switch, the steer-
ing lock, and is used to open the seat to gain access to the
center compartment and the fuel filler cap.
The keys have a unique code that is stamped on the tab sup-
plied with the keys. This code is not stamped on the scooter
and is not recorded in the vehicle's basic documentation for
security reasons. Since this code is required if you need re-
placement keys, record this important code in the box provided
on the inside, rear cover of this Owner's Manual.
Ignition switch & Steering lock
CONTROLS & FEATURES
NOTE: Your scooter’s keys may differ slightly in appearance from
the images in this manual.
1 1 1 1
1 ON: In this position, electrical power is connected to start
and operate the engine (the key cannot be removed).
2 2 2 2
2 OFF: In this position, electrical power is disconnected and
the engine cannot start or operate (the key can be removed).
22
22
2
Key code tab
11
111
10
CONTROLS & FEATURES
After locking the ignition switch, turn the handlebar gen-
tly to confirm that the steering is locked. Do not park
your scooter in a position that will interfere with vehicle
or pedestrian traffic.
Do not turn the ignition switch to the lock position when
riding, as this could cause the steering to lock and you
could lose control of your scooter.
33
333
3 3
3 3
3 LOCK: In this position, the steering is locked, electrical
power is disconnected and the engine cannot start or oper-
ate (the key can be removed).
Locking the steering
Turn the handlebar fully to the left. Press in and rotate the
ignition switch key counterclockwise to the “LOCK” position.
The steering will now be locked. Remove the ignition switch
key.
Unlocking the steering
Insert and rotate the ignition switch key clockwise from the
“LOCK” position to the “OFF” or “ON” position. The steering is
now unlocked, and you may start and operate the scooter.
11
Right handlebar switch
NOTE: The starter motor will not engage unless a brake le-
ver is squeezed at the same time the starter button is pressed.
Electric starter button 22222:
Press the electric starter button to activate the starter motor.
Engine stop switch 11111:
The engine stop switch turns off the ignition, stopping the en-
gine, but the scooter’s lights and horn will still function.
To prevent damage to the starter motor, do not operate
the starter motor for more than five seconds at a time. If
the scooter fails to start immediately, check the fuel level
and the battery condition, and allow the starter motor to
cool before attempting to start the engine again.
CONTROLS & FEATURES
Left handlebar switch
Headlamp switch -- UP
33333:
The upper switch position turns the headlight high beam
The high beam indicator light on the dash is activated as w
Headlamp switch -- DOWN
44444:
The lower switch position turns the headlight low beam on
Passing light button - PRESS DOWN
55555:
When downward pressure is applied to the headlight rock
switch, the high beam is activted. When pressure is release
the the low beam setting is restored. This enables you to rapi
flick the headlight high beam on and off to signal other vehi
that you wish to pass.
11111
22222
33333
44444 55555
12
Under-seat storage compartment
Your scooter is equipped with an under-seat storage compart-
ment that permits you to secure your helmet or other items.
To open the seat, insert the ignition switch key into the seat lock
AT and turn it clockwise. When the latch releases, lift up the seat.
Under-seat compartment weight Iimit: .........11 lbs (5 kg)
To close the seat, lower the seat and press down until it is
secured by the latch. Gently lift up on the seat to make sure it
is locked before riding.
Never exceed the maximum weight limit of the storage
compartment, as vehicle handling and stability may be
severely affected. Do not leave the ignition switch key
under the seat.
Turn signal switch:
Use the turn signal indicator to signal to other traffic that you
intend to turn or change lanes. The turn signal light on the
dash will flash to indicate that the switch is engaged.
66666 Slide the turn switch to the left to activate the left turn
signal.
77777 Slide the turn switch to the right to activate the right turn
signal.
To cancel the turn signal, press down on the signal switch 8.
Horn button 99999:
Press the horn button to sound the horn.
NOTE: The horn will only sound when the ignition is “ON”.
CONTROLS & FEATURES
ATATATATAT
66666 77777
88888
99999
13
CONTROLS & FEATURES
Helmet posts
Your scooter has two helmet posts AK so you can secure your
helmet(s) outside of the under-seat storage compartment.
With the seat up, put the helmet’s retaining ring onto the helmet
post. Lower and press down on the seat to lock it and secure the
helmet in place. To remove the helmet, open the seat.
Do not ride your scooter with a helmet hanging from a
helmet post, as this can interfere with your ability to con-
trol your scooter, and may cause an accident.
The under-seat storage compartment may become warm
from engine heat. Therefore, do not store any items in
this compartment that are susceptible to heat damage,
such as food or flammable materials.
Main stand (center stand)
Your Agility scooter is equipped with a main (center) stand.
Always park your the scooter on firm, level ground to
help prevent it from falling over. If you must park on an
incline, aim the front of your scooter uphill.
To park your scooter on the main stand, stand on the left side
of the scooter and grasp the handlebar with your left hand,
while grasping the side of the rear rack with your right hand.
Step down on the foot pad of the main stand with your foot
while pulling up and back on the rear rack. This lifting motion
will allow the scooter to rock backwards and up onto the main
stand.
AKAKAKAKAK AKAK
AKAK
AK
14
CONTROLS & FEATURES
1 1
1 1
1 Odometer: Indicates the total riding mileage of the scooter.
2222
2 High Beam Indicator Light: This light is illuminated when
the headlight high beam is on.
33
33
3 Clock: Indicates the time (24-hour format).
4 4 4 4
4 Turn Signal Indicator Light: Flashes when either turn
signal is being used.
55
55
5 Speedometer: Indicates the road speed in MPH (miles
per our) and K/PH (kilometers per hour).
66
66
6 Fuel Gauge: This gauge indicates the amount of gasoline
in the fuel tank. Refill the tank with unleaded gasoline be-
fore the needle reaches the “E” (empty) mark. (Best prac-
tice is to maintain the fuel level no lower than the one-
quarter mark above empty whenever possible).
Instruments
22
22
2
33
333
44
444
11
11
1
55
55
5
66666
Your Agility scooter is equipped with a digital clock 7. To set the
clock, follow this procedure:
1. Press and hold the SETTING BUTTON 8 until the clock’s
hour display begins to flash.
2. Press the ADJUST BUTTON 9 to change the clock’s hour
to the desired setting.
3. Press the SETTING BUTTON again so that the clock’s
minute display is flashing.
4. Press the ADJUST BUTTON to adjust the minute setting.
5. Once the desired time is set, press the SETTING BUTTON
once again to finalize your adjustments to the clock’s set-
tings and to release the clock from the adjustment mode.
77
777
88888
99
999
Digital clock
15
CONTROLS & FEATURES
Passenger foot rest
The floorboard of your Agility scooter is equipped with a raised
section AT and floorboard area for use when you are carrying a
passenger.
Riding with a passenger will change the handling char-
acteristics of your scooter. Allow for extra braking dis-
tance and use extra care when riding in traffic.
Be sure you and your passenger always wear an ap-
proved motorcycle helmet that fits properly. You should
also wear eye protection and other protective apparel
when you ride.
ATATATATAT
16
Break-in recommendations
The first 600 miles (1,000 km) of riding are the most important
in the life of your scooter. Following proper break-in proce-
dures during this time will help ensure maximum life and per-
formance from your new scooter. Proper break-in operation
allows the machined surfaces to polish each other and mate
smoothly.
Your scooter’s reliability and performance depend on your
exercise of special care and restraint during the break-in pe-
riod. It is especially important that you avoid operating the
engine in a manner which could expose the engine parts to
excessive heat.
The following guidelines should be followed during the break-
in period:
Maximum throttle operation:
Initial 300 miles (600 km): ........ Less than 1/2 throttle
Up to 600 miles (1,000 km): ..... Less than 3/4 throttle
Vary the engine speed:
The engine speed should be varied and not held at a constant
rate for long periods of time. This allows the parts to be "loaded"
with pressure, and then unloaded, allowing the parts to cool.
This aids in the mating process of the engine and transmis-
sion components. It is essential that some stress be placed on
these components during break-in to ensure that this mating
process occurs. Do not, however, apply excessive load on the
scooter's drive line.
Avoid constant low speed:
Operating the engine at constant low speed (light load) can
cause parts to glaze and not seat in properly. Allow the engine
to accelerate freely through the gears, without exceeding the
recommended throttle openings.
Avoid using full throttle for the first 300 miles (500 km).
The initial service:
The 200 mile (300 km) initial service is the most important
service your scooter will receive. Take extra care to observe
your scooter’s initial service in a timely fashion. During
the break-in period, all of the engine components will have
worn in, and all of the other parts will have seated in, so ad-
justments will be required. All fasteners will be tightened, and
the contaminated engine oil will be replaced.
NOTE: Completion of the 200 mile (300 km) initial service
will ensure optimum service life and performance from
your scooter. Do not delay in having this service performed
SECTION 3 -
OPERATION
17
Breaking in the new tires
New tires need proper break-in to assure maximum perfor-
mance, just as your scooter's engine does. Wear in the tread
surface by gradually increasing your cornering lean angles
over the first 100 miles (160 km) before attempting maximum
lean angles. Avoid hard acceleration, hard cornering, and hard
braking for the first 100 miles (160 km).
The 200 mile (300 km) service should be performed as
outlined in the maintenance schedule section of this
owner's manual. Pay particular attention to the cautions
and warnings in the Maintenance Schedule section.
Unless you have formal training as a service techni-
cian and have access to KYMCO technical reference
materials, it is strongly suggested that you have the
initial service performed by a KYMCO dealer.
Failure to break in your tires could cause the tires to
slip and could result in you losing control of the scooter.
Use extra care when riding on new tires. Perform proper
break-in of the tires as described in this Owner’s Manual
and avoid hard acceleration, hard cornering, and hard
braking for the first 100 miles (160 km).
OPERATION
Troubleshooting
It can be fustrating if your scooter fails to start or stops running
while your are riding. In the rare instance this occurs, take a
few moments to check the following items. This checklist cov-
ers some of the most common, simple problems which may
arise and which can be quickly resolved.
√√√√
√Do you have enough gasoline in the fuel tank?
√√
√√
√Did you follow the correct procedure for starting the
engine?
√√
√√
√Is the battery voltage low (you may need to kick start
your scooter)?
√√√√
√Is the main fuse in good condition?
NOTE: Use this Owner’s Manual to check components and
adjustments that are within your technical ability. If you
cannot resolve the problem, do not hesitate to contact your
KYMCO dealer for assistance.
18
Improperly maintaining your scooter or failing to cor-
rect a problem before riding can cause a crash in which
you can be seriously hurt or killed.
Always perform a pre-ride inspection before every ride
and correct any problems.
6. Steering: Check for smooth operation in all steering posi-
tions (page 23).
7. Instruments: Make sure the speedometer, fuel level gauge
and indicator lights function (page 23).
8. Lights and horn: Check that headlight, tail/brake light, turn
signals, indicators and horn function properly (page 24).
9. Chassis: Check for overall proper function (page 25).
1. Engine oil level: Add engine oil if required (page 19). Check
for leaks.
2. Front and rear brakes: Check operation, making sure there
is proper free-play at the left lever, and that there is brake
fluid in the front brake fluid reservoir (pages 19 & 20).
3. Tires: Check condition and inflation pressure (pages 20 & 21).
4. Fuel level: Fill fuel tank when necessary (page 22). Check
for leaks.
Performing pre-ride inspections does not take the place
of regular maintenance. Follow the maintenance sched-
ule recommendations on pages 33 - 50 of this manual.
After one month of use or 200 miles (300 km) of riding,
which ever occurs first, contact your KYMCO dealer to
have an initial service of your scooter performed.
This initial service is most important service in the life
of your scooter and includes checks and adjustments
that will help ensure that your scooter operates effi-
ciently and safely.
OPERATION
Pre-ride inspection (PRI)
For your safety, it is very important to take a few moments
before each ride to walk around your scooter and check its
condition. If you detect any problem, be sure to address it im-
mediately, or have it corrected by your KYMCO dealer.
19
OPERATION
1. Unscrew the dip stick 1, remove it and wipe it with a clean
cloth
2. Reinsert the dip stick until the threaded part of the dip stick
touches the engine case. Do not thread the dipstick into the
engine case.
3. Remove the dip stick again and inspect the oil level on the
stick. The engine oil level should be above the "L" mark but
not higher than the "F" mark. Add or remove oil as required.
Do not overfill the engine with oil. Overfilling the en-
gine can cause oil leaks and/or oil contamination of
the air filter element. Always make sure the oil level is
above the "L" mark but not higher than the "F" mark.
PRI - Engine oil level inspection
NOTE: Park your scooter on the main stand, on level ground.
L
F
Use extreme caution when performing the oil level in-
spection or any other checks if the scooter’s engine
has been recently run. The engine oil, engine case and
muffler can become very hot creating a burn hazard.
PRI - Rear brake lever inspection (left lever)
1. Measure the free-play at the left brake lever end:
0.4 - 0.6 in (10 - 20 mm).
2. Use the cable adjuster on left brake lever perch for minor
free play adjustment.
Your scooter requires the proper brake lever free-play so the
brakes will be responsive and will not drag, causing prema-
ture wear to the brake pads. The free-play is the measured
distance between the brake lever at rest and the point at which
the brake first begins to engage.
11111
0.4 - 0.6 in
(10 - 20 mm)
20
PRI - Tire inspection
The condition of your scooter’s tires is vital for operational ef-
ficiency and your safety. Check the tires’ inflation pressure,
the tread depth, and for damage before each ride.
1. Measure and adjust the tire pressure when the tires are
touching the ground (with no person on the scooter).
NOTE: Measure the pressure before riding as the heat gen-
erated during operation may cause improper readings.
Front tire (rider only): 17.5 PSI (1.25 kg/cm2)
Rear tire (rider only): 29.0 PSI (2.0 kg/cm 2)
Front tire (rider & passenger): 17.5 PSI (1.25 kg/cm2)
Rear tire (rider & passenger): 32.0 PSI ( 2.25 kg/cm 2)
PRI - Front brake lever & fluid inspection
(right lever)
The right brake lever on your Agility scooter controls the front
hydraulic brake. Check the free-play at the end of the lever so
the brake will be responsive and will not drag, which could
cause premature wear to the brake pads or brake rotor.
OPERATION
1. Measure the free-play at the right brake lever end:
0.4 - 0.6 in (10 - 20 mm).
2. Verify that the fluid level is between the “L” mark 1 and the
“F” mark 2 in the brake fluid reservoir window. See the
MAINTENANCE section of this Owner’s Manual for addi-
tional information about the front brake fluid.
See your KYMCO dealer immediately if the front brake le-
ver free-play is not within specification.
22
22
2
11
111
21
OPERATION
2. Inspect the tires for nails, screws and other objects 3 that
may be imbedded into the rubber.
33333
3. Check the tread depth 4 at the wear indicator points 5. If
the tread is worn smooth at these points, the tire must
be replaced.
44444
55
555
55
555
4. Check for damage 6 (blisters or cuts) in the side wall, or
for significant flat spots 7 on the tires’ tread. Replace the
tire immediately if any damage of this type is present.
66
666
66
666 77
777
The tires on your scooter must be replaced if they:
Leak air (even at a slow rate)
Have any damage on the tread or side wall areas
Have been damaged by intrusion of objects, such as a nail
Are worn as evidenced by the wear indicators
Failure to replace a tire in poor condition will cause an
unsafe riding condition on your scooter. Replace worn or
damaged tires immediately for your, and your passenger’s,
safety.
Consult your KYMCO dealer for replacement tire service.
22
OPERATION
PRI - Fuel level inspection / Refilling
To open the fuel filler cap:
1. With the engine “OFF”, place the scooter on its main stand
and open the seat (see page 12 of this manual).
When the fuel level gauge needle approaches “E” (indicating
the tank is nearly empty) refill the tank with unleaded gasoline. Do not overfill the tank. There should be no fuel in the
fuel filler neck. Excess fuel can contaminate the evapo-
rative emission canister, resulting in poor drivability.
Fuel recommendation
Use unleaded gasoline with a research octane number of 91
or higher. Unleaded gasoline will extend spark plug life.
Gasoline is highly flammable and explosive. You can be
burned or seriously injured while handling fuel.
* Stop the engine and keep heat, sparks, and flame away.
* Refuel only out doors.
* Clean up fuel spills immediately.
2. Insert the ignition switch key into the lock on the fuel filler
cap 1 and rotate the key counterclockwise to unlock and
open the cap.
3. Add fuel (per the recommendations listed in this manual).
11
111
4. Replace the fuel filler cap by aligning the tabs on the cap
with the slots in the fuel filler neck.
5. When closing the cap, press down on the cap slightly and
rotate the ignition switch key clockwise to lock the cap into
place.
6. Remove the key from the fuel filler cap and close the seat.
23
OPERATION
1. Visually inspect the handlebars for any damage.
2. Apply the front brake (right lever) and press down and re-
lease pressure on the handlebar, listening for any abnormal
noise.
3. As you press down and release, also feel for any looseness
from the chassis transmitted to the handlebar.
4. Turn the handlebar from the center fully to the left and then
fully to the right, feeling for any loose components and lis-
tening for any abnormal sounds.
PRI - Steering & handlebar inspection
Before riding, inspect your scooter’s handlebars for damage,
and make sure the steering’s side-to-side and up-and-down
movement is smooth. If you detect any looseness or abnormal sounds dur-
ing your steering inspection, do not ride your scooter.
Consult your KYMCO dealer for chassis service.
PRI - Instrument inspection
Before your ride, and as you begin your ride, make sure the
instruments are functioning.
1. Do the indicator lights 1 (turn signal, for example) function?
2. Does the speedometer 2 needle move as the scooter moves?
3. Does the fuel level gauge needle 3 indicate the fuel level?
11
111
22
222
33
33
3
NOTE: Contact your KYMCO dealer for repair of your
scooter’s instruments if they are not functioning properly.
24
1. Turn the ignition switch to “ ON“ and press the horn button
on the left handlebar switch to check if it sounds.
OPERATION
2. Turn on the headlight switch to see if the headlight 1 and
the tail light 3 are illuminated. Check the lenses for dirt or
damage.
3. Operate the turn signal switch to make sure the turn signals
2 flash. Make sure each of the four signals flash and the
lenses are free of dirt and are not broken.
4. Squeeze each brake lever to make sure the brake lamp in
the tail light 4 illuminates.
The horn is an essential safety item, as it alerts other
traffic to your presence.
The headlight must be in good working order to illumi-
nate your riding path at night.
The tail/brake light is required so others in traffic can
see your scooter and be alerted to your intention to stop
or slow down.
The turn signals indicate your turning intentions.
Because all of these systems are vital safety items, con-
tact your KYMCO dealer for replacement bulbs or elec-
trical system service or repair should there be any mal-
functions.
PRI - Horn & lights inspection
11
111
22
222
33
33
3
25
PRI - Chassis inspection
Complete the pre-ride inspection of your scooter by checking
items on its chassis.
OPERATION
Front suspension & rear shock absorber: Check the op-
eration of the suspension by pressing down on the handlebars
and seat. Make sure the suspension returns in a smooth fash-
ion.
Brake lever operation: Check that the rear brake (left lever)
and the front brake (right lever) have pressure and lock the
wheels when you squeeze the levers.
Mirrors: Adjust the mirrors while seated on the scooter BE-
FORE you begin riding.
License plate: Make sure your license plate is securely
mounted and your registration is current.
Reflectors: Look to make sure all of the safety reflectors are
still mounted to your scooter. Replace any missing or dam-
aged reflectors.
Lubrication points: Occasionally check and lubricate certain
controls and points on the scooter as called out in the periodic
maintenance schedule (see pages 24 & 35).
26
OPERATION
Starting the engine (electric start)
To start your scooter using the electric starting motor, follow
this procedure:
1. Unlock the steering with the ignition switch key and turn the
ignition switch to “ON“.
NOTE: Before starting, check the engine oil and fuel lev-
els. Take the scooter off of the main stand.
2. Apply the rear brake (left lever) .
The brake must be adjusted and functioning properly
to lock the rear wheel during starting or the scooter
could accelerate away when the engine starts.
To prevent damage to the starter motor, do not operate
the starter motor for more than five seconds at a time. If
the scooter fails to start immediately, check the fuel level
and the battery condition, and allow the starter motor to
cool before attempting to start the engine again.
3. Press the starter button 1 without rotating the throttle grip.
NOTE: If the scooter’s engine is warm and does not start
immediately, rotate the throttle grip to 1/8 to 1/4 open to
help the engine start.
NOTE: The rear brake must be held for the starter motor
to engage the engine. It is normal for the stop light to be
illuminated during starting.
11
11
1
27
OPERATION
Your scooter's exhaust emits poisonous carbon mon-
oxide gas. High levels of carbon monoxide can collect
rapidly in enclosed areas such as a garage. Do not run
the scooter's engine with the garage door closed. Even
with the door open, run the engine only long enough
to move your scooter out of the garage.
3. While squeezing the rear brake lever, kick down on the
kick start lever without rotating the throttle grip.
Once the scooter starts, the rear wheel may spin. To
avoid injury, keep your body and clothing away from
the rear wheel.
NOTE: If the scooter has not been ridden for a long pe-
riod of time it may be hard to start. Add fresh fuel and
press the starter button several times in succession to
try to start the engine. If the scooter does not start, con-
tact your KYMCO dealer as your scooter may need to have
its fuel system cleaned and adjusted.
Do not press the starter button once the engine is run-
ning or the starter motor and engine may be damaged.
Starting the engine (kick start)
To start your scooter using the kick start lever, follow the elec-
tric starting procedure, except use the kick lever in place of the
electric start button.
4. Allow a cold engine to warm up 2 - 3 minutes before riding.
NOTE: If the scooter’s engine is warm and does not start
immediately, rotate the throttle grip to 1/8 to 1/4 open to
help the engine start.
Once the scooter is started, fold the kick start lever
back to its original position.
28
OPERATION
Riding your scooter
NOTE: After starting, allow the engine oil to circulate be-
fore riding your scooter. Allow sufficient idling time after
warm or cold engine start-up before applying load or rev-
ving the engine. This allows time for the lubricating oil to
reach all the critical engine components.
NOTE: Review the scooter safety recommendations on
pages 2 through 6 before you ride.
Make sure flammable materials such as dry grass or
leaves do not come into contact with the exhaust sys-
tem when riding, idling, or parking your scooter.
1. Make sure the throttle is closed and the rear brake is en-
gaged before moving the scooter off the main stand.
You and your passenger should always wear appropriate
safety apparel such as a helmet, eye protection, gloves
and other protective clothing each time you ride the scooter.
Never wear any items that will adversely affect your safety.
2. Mount the scooter from the left side and sit in an upright
position on the seat. Place both hands on the handlebars
and touch the ground with your left foot 1 for stability.
3. Release the rear brake and slowly rotate the throttle grip
so that the engine power will be transmitted smoothly to
the rear wheel.
Use the scooter’s turn signals to signal your intention to
merge into traffic. Always scan around you and check the
rear view mirrors so you are aware of other traffic. Use
caution as you merge into traffic, keeping to the right until
you match the pace of the traffic.
11
111
29
OPERATION
4. Control the scooter’s speed with the throttle grip.
Rotating the grip towards you 2 will increase the scooter’s
speed.
Rotating the grip away from you will decrease the scooter’s
speed.
5. Limit the maximum speed of your scooter during the first
600 miles (1,000 km) of operation. Keep the road speed
below 25 MPH (40 KPH) during this break-in period.
In hot weather the engine could overheat if it idles for a
long period of time. Very slow speed traffic could also
cause the scooter to overhead. To promote engine lon-
gevity permit the engine to cool in these situations.
Avoid sudden acceleration and prolonged high speed
use that can accelerate engine wear.
Moderate use will prolong the engine life of the scooter.
22
222
6. Use both brake levers when slowing and stopping the
scooter. Release the throttle when braking.
NOTE: Decreasing the scooter’s speed with a balanced
application of both brake levers and a reduction of throttle
will reduce the distance required to stop. Squeeze the le-
vers lightly at first and then increase the pressure when
stopping.
Avoid using just one brake to stop the scooter, as this will
affect the tires’ grip.
Avoid sudden braking as this will also affect the tires’ grip
and can cause an accident.
30
OPERATION
NOTE: At certain speeds your scooter will turn more ef-
fectively by leaning your body, than by applying pressure
on the handlebars. Practice steering in an open, traffic-
free area until you are familiar with the handling charac-
teristics of your scooter.
Reduce your speed when riding on uneven or loose road
surfaces. When riding downhill, use less throttle and inter-
mittently brake to control the vehicle’s speed. These con-
ditions reduce tire grip and can cause an accident.
Reduce your speed when riding your scooter in the rain.
Wet road surfaces reduce tire grip and greatly increases
the distance required for safe braking. The wet surface
also reduces tires grip during cornering. Reduced tire grip
will make it more difficult to control your scooter and may
cause an accident.
8. As you approach a turn, or plan to stop, use the turn sig-
nals well in advance to alert other traffic of your intentions.
Scan for other vehicles around you and slowly move to the
right side of the road. Close the throttle, apply the brake
smoothly, as the brake light will warn vehicles behind you
that you are braking.
7. When riding and turning the scooter, use smooth move-
ments.
31
OPERATION
9. When you stop the scooter, press the center of the turn
signal indicator switch to cancel the signal flashing. Turn
the ignition switch to the “OFF“ position to stop the engine
and turn off the scooter’s electrical system.
Never operate the ignition switch while riding your scooter.
If the ignition switch is turned during riding it could turn
off the engine and lights, possibly causing you to lose con-
trol of the scooter.
With the lights off, your scooter may not be visible to other
traffic, and this could cause a traffic accident.
Only operate the ignition switch when the scooter is not
moving.
Parking your scooter
Use the following procedure and suggestions when parking
your scooter.
1. Place the scooter on level ground.
2. Stand on the left side of the scooter and grasp the handle-
bar with your left hand, while grasping the side of the rear
rack with your right hand. Step down on the foot pad of the
main stand with your foot while pulling up and back on the
rear rack. This lifting motion will allow the scooter to rock
backwards and up onto the main stand.
32
OPERATION
The scooter may fall over if it is not parked on level
ground.
Make sure flammable materials such as dry grass or
leaves do not come into contact with the exhaust sys-
tem when parking your scooter.
Lock the steering of your scooter (see pages 9 & 10) to
reduce the risk of theft.
Do not park your scooter in a place that hinders traffic,
or that is unsafe to you or others.
33
SECTION 4 -
MAINTENANCE
The importance of maintenance
Maintaining your scooter properly is essential for safe, eco-
nomical and trouble-free riding. It will also help reduce air pol-
lution and maximize fuel economy.
To help you properly care for your scooter, the following pages
in this Owner's Manual include a maintenance schedule to
help you make sure your scooter is serviced at the appropri-
ate intervals.
These instructions are based on the assumption that your
scooter will be used exclusively for its designed purpose. Sus-
tained, high-speed operation, or operation in unusually wet or
dusty conditions, will require more frequent service than speci-
fied in the maintenance schedule. Consult your KYMCO dealer
for recommendations applicable to your individual needs and
use.
NOTE: Always follow the inspection and maintenance rec-
ommendations and schedules in this Owner's Manual.
When performing maintenance on your scooter you may
need to start the engine. Running your scooter's en-
gine indoors or in a garage can be hazardous. Exhaust
gas contains carbon monoxide, a gas that is colorless
and odorless, and can cause death or severe injury.
Operate the engine only where there is adequate venti-
lation, preferably outdoors.
If your scooter tips over or becomes involved in a crash,
be sure your KYMCO dealer inspects all major parts,
even if you are able to make some repairs.
Improperly maintaining this scooter or failing to cor-
rect a problem before you ride could result in a crash in
which you could be seriously hurt or killed.
34
MAINTENANCE
Maintenance Schedule
Perform the pre-ride inspection (see pages 18 - 25) at each scheduled maintenance period. This interval should be judged by
odometer reading or months, whichever comes first.
Maintenance Schedule Legend (see page 35):
I: INSPECT AND CLEAN, ADJUST, LUBRICATE OR REPLACE IF NECESSARY
C R A L: CLEAN : REPLACE : ADJUST : LUBRICATE T: TIGHTEN
The maintenance schedule on page 35 specifies the maintenance required to keep your Agility scooter in peak operating
condition. Maintenance work should be performed in accordance with KYMCO standards and specifications by properly trained
and equipped technicians. Your KYMCO dealer meets all of these requirements.
*Should be serviced by your KYMCO dealer, unless you have the proper tools, service data and are technically qualified.
* * In the interest of safety, we recommend these items be serviced only by your KYMCO dealer. KYMCO USA recommends
that your KYMCO dealer road test your scooter after each periodic maintenance service is completed.
Maintenance Schedule Notes (see page 35):
1. At higher odometer readings, repeat at the frequency interval listed here.
2. Service more frequently if the scooter is ridden in unusually wet or dusty areas.
3. Service more frequently when riding in rain or at full throttle.
4. “PRI” indicates that the item should be checked as part of the Pre-Ride Inspection (see page 18 through 25)
5. “See page” indicates on which page of the Owner’s Manual you will find information about the required maintenance.
6. “Dealer” indicates maintenance or service procedure that should be performed by your KYMCO dealer.
35
MILEAGE 200 mi 600 mi 1850 mi 3100 mi 4300 mi 5500 mi 7000 mi Pre-ride See
ITEM 300 km 1000 km 3000 km 5000 km 7000 km 9000 km 11000 km inspection page
Engine oil * R R R R R R R PRI 19, 40
Engine oil strainer * C - C - C - C - 40
Gear oil * R - R - R - R - 42
Spark plug * C I C R C I R - 43
Valve clearance ** A - A - A - A - Dealer
Carburetor ** I - I - I - I - Dealer
Drive belt ** - - - - I - - - Dealer
Air cleaner * C I R I R I R - 37
Battery * I I I I I I I PRI 38, 39
Fuel filter ** - - - - R - - - Dealer
Brake system ** I I I I I I I PRI 19, 43
Tires ** I I I I I I I PRI 20, 36
Bolts & nuts * T I I T I I T PRI 25
Maintenance Schedule - Agility 50 & 125
MAINTENANCE
I: INSPECT AND CLEAN, ADJUST, LUBRICATE OR REPLACE IF NECESSARY
C R A L: CLEAN : REPLACE : ADJUST : LUBRICATE T: TIGHTEN
36
MAINTENANCE
Tires
NOTE: Check the tire inflation pressure and tire tread con-
dition at the periods listed in the Periodic Maintenance
Schedule. For maximum safety and good tire life, the tire
pressures should be inspected more often.
Failure to follow these warnings may result in an acci-
dent due to tire failure. The tires on your scooter are a
crucial link between your scooter and the road. You and
your passenger's personal safety are dependant upon
the condition of your scooter's tires.
Follow these instructions:
Check tire condition and pressure, and adjust the
inflation pressure before each ride.
Avoid overloading your scooter.
Replace a tire when worn to the specified limit, or
if you find any damage such as cuts or cracks.
Always use the proper size and type of tires as
specified in this Owner's Manual.
Balance the wheel after tire installation.
Read this section of Owner's Manual carefully.
Failure to perform a reasonable break-in of the tires
could cause tire slip and loss of control.
Use extra care when riding on new tires, as the grip
will be limited. Perform proper break-in of the tires, as
set forth in the break-in recommendation section of this
manual. Avoid hard acceleration, hard cornering, and
hard braking for the first 100 miles (160 km).
Tire pressure
Insufficient air pressure in the tires not only accelerates tire
wear, but it also affects the stability of your scooter. Under-
inflated tires make smooth cornering difficult, and overinflated
tires decrease the amount of tire in contact with the ground,
which can lead to skids and loss of control. Make sure that the
tire pressures on your scooter are within the specified limits at
all times.
NOTE: Tire pressure should only be adjusted when the
tires are cold.
Front tire (rider only): 17.5 PSI (1.25 kg/cm2)
Rear tire (rider only): 29.0 PSI (2.0 kg/cm 2
)
Front tire (rider & passenger): 17.5 PSI (1.25 kg/cm2)
Rear tire (rider & passenger): 32.0 PSI ( 2.25 kg/cm 2)
37
MAINTENANCE
Air cleaner filter element
The air cleaner filter element should be serviced at regular
intervals. Service the element more often when riding in un-
usually wet or dusty areas.
1. Open seat (see page 12).
2. Remove air cleaner cover screws 1.
3. Remove the air cleaner case cover 2.
4. Remove the air cleaner element
5. If lightly soiled, clean the filter 3 with compressed air. If very
dirty (or if the filter is at the replacement interval per the main-
tenance schedule) discard the air cleaner element.
6. Install the cleaned or new air cleaner element. Use the
KYMCO genuine air cleaner element or an equivalent air
cleaner element specified for your scooter.
7. Complete the installation by reinstalling the air cleaner parts in
the reverse order of removal.
Improper installation for the filter can cause water or
dirt to enter the engine causing premature wear.
Using the wrong KYMCO air cleaner element or a non-
KYMCO air cleaner element which is not of equivalent
quality may cause premature engine wear or perfor-
mance problems.
11
111
22222
33
333
38
MAINTENANCE
Fuel system & hoses
Check the fuel hoses and fittings for any signs of leakage.
1. Check for leakage at the carburetor 1.
2. Check for leakage from the fuel hoses, clamps and joints 2.
3. Check for leakage at the fuel filter 3.
4. Check for leakage at the fuel tank 4.
Replace any fuel system components that are leaking fuel.
Contact your KYMCO dealer for fuel system service and
repairs.
Battery
Your KYMCO scooter is equipped with a maintenance-free
(sealed) battery. Therefore, it is not necessary to check the
battery's electrolyte level or add distilled water.
NOTE: If your battery seems weak and/or is leaking elec-
trolyte (causing hard starting or other electrical troubles),
contact your KYMCO dealer immediately .
Your battery is a maintenance-free type and can be per-
manently damaged if the cap strip is removed.
Charge the battery with a charger specifically designed
for use with a maintenance-free type battery. Using an-
other type of charger can damage the battery.
Your scooter's battery gives off explosive hydrogen gas
during normal operation. A spark or flame can cause
the battery to explode with enough force to kill or seri-
ously injure you. Wear protective clothing and a face
shield, or have a qualified technician perform the bat-
tery maintenance.
11111
22
22
2
33333 44
444
39
MAINTENANCE
Battery removal & installation
The battery 5 is in the battery box below seat.
Fuses
When frequent fuse failures occur, it usually indicates a short
circuit or an overload in the electrical system.
Fuse replacement
FUSE SIZE: 7A (One MAIN fuse & one SPARE)
NOTE: See your KYMCO dealer for electrical system
diagnosis and repair.
Never use a fuse with a different rating from that speci-
fied. Serious damage to the electrical system or a fire
hazard may result, causing a dangerous loss of lights
or engine power.
1. When removing the battery for charging or replacement, dis-
connect the negative (-) terminal lead from the battery first,
then disconnect the positive (+) terminal lead.
2. When installing the battery, connect the positive terminal
lead (+) first, then the negative terminal lead (-).
1. Open the fuse holder 6.
Pull the fuse holder clips
7 out of the holder.
2. Slide the fuse 8 out of
the holder clips.
3. Install a new fuse 8 of
the proper specification
into the holder clips.
4. Press the fuse and the
holder clips 7 back into
the holder.
5. Close the fuse holder 6
and set it back in place.
66
666
66
666
77777
88
88
8
88
88
8
77
777
NOTE: Always keep ignition switch OFF when servicing
the battery.
55555
40
Engine oil
Engine oil recommendation
Use a premium quality 4-stroke engine oil to ensure longer
service life of your scooter. Only use oils that have a SJ rating
per the API service classification.
Engine oil capacity: 0.95 qt (0.9 L)
Engine oil viscosity: SAE 15W-40
If this viscosity is not available, select an alternative engine
oil according to the chart shown below.
ENGINE OIL VISCOSITIES
Engine oil level inspection
Check the engine oil level each day before riding your scooter
(see page 19).
The engine and related components can become very hot.
Use care when inspecting or adjusting the oil level to avoid
injury. If needed, let the engine and exhaust system cool
before working in those areas.
Prolonged contact with used engine oil can cause skin
cancer. Although rare, this possibility exists if you handle
oil on a frequent basis. Thoroughly wash your hands with
soap and water as soon as possible after handling used
oil.
Engine oil replacement
Engine oil quality is the primary factor affecting engine longev-
ity. Change your scooter's engine oil as specified in the main-
tenance schedule (see page 35).
NOTE: When riding your scooter in very dusty conditions,
oil changes should be performed more frequently than
specified in the maintenance schedule.
NOTE: Always dispose of used engine oil in a environ-
mentally responsible manner. You should take the drained
oil in a sealed container to your local recycling center or
service station for reclamation. Do not throw the oil in the
trash, pour it on the ground, or pour it down a drain.
NOTE: Change the engine oil with the engine at normal
operating temperature, with the scooter positioned on its
main stand, to assure complete and rapid draining.
MAINTENANCE
41
1. Place a suitable container (drain pan) under the left crank-
case. Remove the drain bolt 1 to drain the oil.
3. Replace the drain bolt 1. Tighten it to the specified torque.
Do not overfill the engine with oil. Overfilling the en-
gine can cause oil leaks and/or oil contamination of
the air filter element. Always make sure the oil level is
above the "L" mark but not higher than the "F" mark
on the dipstick.
Engine oil capacity: 0.95 qt (0.9 L)
Engine oil viscosity: SAE 15W-40
5. Refer to page 19: Wipe the dipstick 2 off with a clean cloth
and reinstall it in its hole, but do not thread it into the engine
case. Push the dip stick in until it touches the case.
6. Remove the dip stick and visually inspect the oil level on the
stick. The engine oil level should be above the "L" mark but
not higher than the "F" mark. Add or remove oil as required.
7. Replace the oil filler/dipstick and tighten it securely.
MAINTENANCE
Oil drain plug torque: 18 lb-ft (25 N-m)
4. Add engine oil through the oil filler/dipstick hole.
11
111
2. Remove the oil filler/dipstick 2 from the right crankcase
cover.
22
222
42
MAINTENANCE
Transmission fluid change
1. Place the scooter on its main stand. 3. After the fluid has drained out, reinstall the drain bolt with a
new sealing washer and tighten it to the specified torque.
2. Place a suitable container (drain pan) under the transmis-
sion case on its left side. Remove the drain bolt 1 to
drain the fluid.
Transmission fluid type: SAE 90
Transmission fluid capacity (Agility 50): 0.12 qt (0.11 L)
Transmission fluid capacity (Agility 125): 0.21 qt (0.20 L)
NOTE: The fill amount specified is the amount to use after
completely draining the used transmission fluid.
Transmission fluid drain bolt torque: 15 lb-ft (20 N-m)
4. Remove the transmission fluid filler bolt 2.
5. Add the exact specified fluid through the fluid filler hole 3.
Using the wrong transmission fluid type or viscosity
may cause premature transmission component wear.
Do not exceed the specified amount when adding trans-
mission fluid. If too much fluid is added to the trans-
mission case it could be forced into the air cleaner as-
sembly during operation, causing air filter contamina-
tion and poor engine performance.
11
11
1
22222
33
333
Produktspecifikationer
| Varumärke: | Kymco |
| Kategori: | Skotrar |
| Modell: | Agility 125 |
Behöver du hjälp?
Om du behöver hjälp med Kymco Agility 125 ställ en fråga nedan och andra användare kommer att svara dig
Skotrar Kymco Manualer
31 Juli 2024
27 Juli 2024
25 Juli 2024
Skotrar Manualer
- Skotrar Yamaha
- Skotrar Aprilia
- Skotrar Peugeot
- Skotrar Hyosung
- Skotrar Nimoto
- Skotrar Honda
- Skotrar Bintelli
- Skotrar Niu
- Skotrar Benelli
- Skotrar Turbho
- Skotrar EVT
Nyaste Skotrar Manualer
19 Oktober 2024
17 Oktober 2024
16 Oktober 2024
12 Oktober 2024
12 Oktober 2024
10 Oktober 2024
7 Oktober 2024
30 Juli 2024
30 Juli 2024
29 Juli 2024