Lasko AK110LS6 Bruksanvisning

Lasko Fläkt AK110LS6

Läs nedan 📖 manual på svenska för Lasko AK110LS6 (12 sidor) i kategorin Fläkt. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/12

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

SAVE THESE INSTRUCTIONS

www.airkinglimited.com

6728081 Rev. D 1-16 1 of 12

Exhaust Fan

AKLS, AKLS6, AKLS6H Series

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN

THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL

INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should

always be followed to reduce the risk of ﬁre, electric shock and

injury to person, including the following:

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer.

b) Before servicing or cleaning the unit, switch power off at service

panel and lock the service disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualiﬁed

person(s) in accordance with all applicable codes and standards,

including ﬁre-related construction.

b) Sufﬁcient air is needed for proper combustion and exhausting of

gases through the ﬂue (chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment manufacturer’s guideline

and safety standards such as those published by the National Fire

Protection Association (NFPA) and the American Society for Heating,

Refrigeration, and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

CAUTION: FOR GENERAL VENTILATING USE ONLY.

DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE

MATERIALS AND VAPORS.

d) Ducted fans must always be vented to the outdoors.

e) This unit must be grounded.

f) To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

g) Read all instructions before installing or using exhaust fan.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, DO NOT USE THIS FAN WITH

ANY SOLID-STATE SPEED CONTROL DEVICE.

a) If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected to a

GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.

WARNING: DO NOT USE IN KITCHENS.

WARNING: THE DUCTING FROM THIS FAN TO THE

OUTSIDE OF THE BUILDING HAS A STRONG EFFECT

ON THE AIR FLOW, NOISE AND ENERGY USE OF THE FAN. USE

THE SHORTEST, STRAIGHTEST DUCT ROUTING POSSIBLE FOR

BEST PERFORMANCE, AND AVOID INSTALLING THE FAN WITH

SMALLER DUCTS THAN RECOMMENDED. INSULATION AROUND

THE DUCTS CAN REDUCE ENERGY LOSS AND INHIBIT MOLD

GROWTH. FANS INSTALLED WITH EXISTING DUCTS MAY NOT

ACHIEVE THEIR RATED AIRFLOW.

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Exhaust Fan

1. Unpack fan from the carton and conﬁrm that all pieces are present. In addition to the

exhaust fan you should have:

1 - Grill

1 - Damper Assembly (attached)

4 - Mounting Rails

1 - Instruction/Safety Sheet

2. Choose the location for your fan. To ensure the best air and sound performance, it

is recommended that the length of ducting and the number of elbows be kept to a

minimum, the radius of each elbow be as large as possible for the installation, and that

insulated hard ducting be used. This fan will require

at least 8” of clearance in the ceiling or wall, and

will mount through drywall up to 3/4” thick. The fan

mounts between 16” or 24” on center joists using the

4 provided mounting rails.

3. Select the most convenient electrical knockout and

remove using a straight-blade screw driver (Figure 1).

4. No additional vibration deadening materials are

needed for this fan.

SECTION 2

New Construction

1. Install the rails into the mounting channel on the housing. Center the mounting channel in

the slots on the housing, then from inside the housing tighten the mounting channel screws

so the channel is securely in place. Position the housing next to the joist. Line up housing so

that it will be ﬂush with the ﬁnished ceiling. Secure the ends of the rails with screws or nails

(not included) to the joists and slide the housing into the ﬁnal position (Figure 2).

SECTION 3

Existing Construction

1. Set housing in position between the joist and trace an outline onto the ceiling material

(Figure 3). Set housing aside and cut opening, being careful not to cut or damage any

electrical or other hidden utilities. Install the rails into the mounting channel on the

housing. Center the mounting channel in the slots on the housing, then from inside

the housing tighten the mounting channel screws so the channel is securely in place.

Position the housing in the previously cut hole so that it is ﬂush with the ﬁnished ceiling.

Secure the ends of the rails to the joists (Figure 2).

www.airkinglimited.com

6728081 Rev. D 1-16 2 of 12

SECTION 4

Ducting

NOTE: 4" (LS) OR 6" (LS6, LS6H) OR LARGER RIGID DUCT IS RECOMMENDED FOR BEST

PERFORMANCE.

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND

NATIONAL BUILDING CODES.

NOTE: The ducting from this fan to the outside of the building has a strong effect on the air

ﬂow, noise and energy use of the fan. Use the shortest, straightest duct routing possible

for best performance, and avoid installing the fan with smaller ducts than recommended.

Insulation around the ducts can reduce energy loss and inhibit mold growth. Fans installed

with existing ducts may not achieve their rated air ﬂow.

1. Connect the proper size ducting (AKLS - 4" round, AKLS6, AKLS6H, 6" round) to the

fan’s duct collar Secure in place using tape or screw clamp. Always duct (Figure 4).

the fan to the outside through a wall or roof cap. It is recommended that low restriction

termination ﬁttings be used.

2. Ensure duct joints and exterior penetrations are sealed with caulk or other similar

material to create an air-tight path to minimize building heat loss or gain and to reduce

the potential for condensation. Place/wrap insulation around duct and/or fan in order to

minimize possible condensation buildup within the duct, as well as building heat loss or

gain (Figure 5).

SECTION 5

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE

MADE IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR

NATIONAL ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING

ELECTRICAL WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.

NOTE: This unit includes a side access panel for wiring that does not require the removal of the

fan’s blower assembly. If you choose to wire the unit from the inside, you will need to remove

the blower assembly and internal wiring compartment. Both methods are equally effective.

1a. Remove the wire compartment cover screw and place External Wire Compartment:

cover in a secure place (Figure 6).

Figure 1

Figure 2

Housing

Joist

Mounting Rails

Ducting

Duct

Collar

Figure 4

Figure 3

Joist

Figure 5

Insulation*

(place around and

over Fan Housing

Fan Housing

Power Cable*

Seal gaps

around Housing

Round

Duct*

Seal duct joints

with tape

Round

Elbows*

Wall Cap*

Roof Cap*

(with built-in

damper)

Keep duct

runs short

*Purchase separately

1b. If the motor is already installed in the housing, remove Internal Wire Compartment:

the two screws holding the blower assembly in place. Lift up on the assembly and slide

it out of the tabs on the housing . Remove the wire compartment cover screw (Figure 7)

and place the cover in a secure place (Figure 8).

NOTE: If the fan motor plug is connected to the fan housing receptacle, unplug so the blower

assembly can be completely removed.

Standard Models

2a. Run wiring from an approved wall switch carrying the appropriate rating. One neutral

(white), one ground (green or bare copper), and one hot (black lead connected to the switch).

Secure the electrical wires to the housing with an approved electrical connector. Make sure

you leave enough wiring in the box to make the connection to the fan’s receptacle.

2b. From where you have chosen to access the fan’s junction box, connect the White wire

from the house to the White wire from the fan’s receptacle. Connect the Black wire from

the wall switch to the Black wire from the fan’s receptacle. Connect the ground wire

from the house to the Green wire from the fan’s receptacle . Use approved (Figure 9)

methods for all connections.

Humidity Sensing Models

3a. For proper operation the humidity sensing fan will require a 3 way switch (not included).

Run wiring between the fan and the switch location. Make sure you leave enough wiring

in each box to make the connections. At the switch box connect the Black wire from

the house to the common terminal of the switch. Connect the black wire from the fan to

www.airkinglimited.com

6728081 Rev. D 1-16 3 of 12

one of the switched terminals on the switch. This position will energize the automatic

mode and the fan will energize upon a rise in humidity. Connect the Red wire from the

fan to the other switched terminal on the switch. This position will activate the Manual

On feature and energize the fan. Properly connect the ground and neutral (if applicable)

mount the switch and the cover.

3b. From where you have chosen to access the fan’s junction box, connect the white wire

from the house to the white wire from the fan. Connect the wire from the automatic

position on the wall switch to the black wire from the fan, connect the wire from the

manual On position on the switch to the red wire from the fan. Connect the ground

wire from the house to the green wire from the fan housing . Use approved (Figure 10)

methods for all connections.

NOTE: The fan’s receptacle wires might need to be pulled outside compartment for connection.

Only pull the three loose wires outside of compartment. Additional wires will be present.

4. Carefully tuck wire back inside wire compartment and replace wire compartment cover

securing with the screw that was removed earlier.

SECTION 6

Completing the Installation

1. Use a sealant appropriate for contact with the building materials present and for the

temperature requirements of the installation to prevent air leakage from unconditioned

spaces is recommended. If gaps between unit housing and ceiling are great, additional

material (backing rod, ceiling material) may be required.

NOTE: This fan is rated for direct insulation contact (Type IC) and it is recommended that this fan

be completely covered by insulation in order to reduce heat loss or gain to unconditioned space.

2. If the fan’s blower assembly was removed during the wiring process, reinstall the

blower by reversing the directions in (Wiring), Section 5 Step 1b.

3a. Plug the fan’s quick connect motor cord into the receptacle. This cord AKLS MODELS:

will only ﬁt one way into the receptacle (Figure 11).

3b. AKLS6 MODELS: Plug the fan’s 5 pin quick connect motor cord into the included

harness. Plug the 3 pin quick connect harness cord into the receptacle located on top of

the wire compartment. These cords will only ﬁt one way into the receptacles (Figure 12).

Figure 6

Screw

Wire

Compartment

Cover

Figure 9

Supply from

house

Ground White

Hot (Black)

Figure 8

Screw

Wire Compartment

Cover

NOTE: Wire compartment conﬁguration will be dependent on model.

Figure 11

Figure 10

Supply from house

Ground White

Hot (Black) Red

Figure 12

Plug

Figure 7

Screws

Tabs

Produktspecifikationer

Varumärke:	Lasko
Kategori:	Fläkt
Modell:	AK110LS6
Färg på produkten:	Blauw
Användarmanual:	Ja
LED-indikatorer:	Bezig met opladen
Batterikapacitet:	5000 mAh
Inspänning:	5.2 V
Strömspänningsskydd:	Over current, Overcharge, Overdischarge, Short circuit
Spännande:	5 V
Laddare kompatibilitet:	Universeel
Antal samtidigt anslutna enheter (max):	1
Mikro-USB-kontakt:	Ja