LevelOne PPM-1000 Bruksanvisning

LevelOne Kablar för PC och kringutrustning PPM-1000

Läs nedan 📖 manual på svenska för LevelOne PPM-1000 (3 sidor) i kategorin Kablar för PC och kringutrustning. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/3
LevelOne
User Manual
PPM-1000
PoE Power Measurement
On-site PoE Power Measurement
PPM- OVERVIEW 1000
PPM- a handheld tester for the applications of 1000 is
Power over Ethernet (PoE). It performs -site on
measurement of the running voltage and supplying power
at the end of Ethernet cable terminal in any length for PoE
PSE/PD devices which complies with IEEE802.3af.
PPM- provides for field engineer a convenient on-site 1000
tester with compact size to verify PoE, measure the voltage,
and examine the maximum power from PSE to PD at the
end point of the Ethernet cable.
Powered by replaceable and rechargeable battery, the
portable - allows the technical personnel to test PPM 1000
terminal for PD in the fields .
With 3- git LED display, it shows the PoE status and the di
maximum power available from . Pass/Fail LED PSE
indicators may inform technician the results instantly.
With built-in Terminal Block connectors, - is able PPM 1000
to clamp and hold the bare wires of network cable for test
before clamping to the RJ-45 connector. - is in PPM 1000
truly the best handy tool for the installation of PoE PD
devices. With the tester, it shall successfully guarantee
the PoE power provision to PD devices.
Mechanical Description
LED Indicators
Buttons and LED Indicators
Start/Set(-) Button
：
：
：
：：
Set the desire maximum power (Watt) for test:
Push and hold Start/Set(- button for 3 seconds to enter for )
configuration of maximum power limit It confirms with . a
beep sound and the 3-digit LED display start blinking.
Press the Start/Set(-) or Start/Set(- buttons to set the )
desired power limit Then, push and hold Start/Set(- button )
for 3 seconds to exit the configuration stage.
Press once to start measurement and press again to finish
the test procedure.
Display/Set(+) Button
Select options for display the Voltage, Power ing
Consumption Limit and Temperature.
While LED PWR/TEST is in during testing torange , he
3-digit Display shows the instantaneous power s. value
While LED PWR/TEST is in t 3-digit display will green, he
show the final result of power measurement.
Note that if the LED OK/NG is in , it indicates the green OK
power from PSE is able to provide the desired power
consumption limit; else LED OK/NG will be in orange NG,
indicating the power is not enough for the PD requirement.
Display/Set(+) Button
Console Port (for upgrade)
Network RJ45 UTP Port
Start/Set(-) Button
Power Probing Terminal
USB Power Port
External Battery Pack
3-Digit Display
LED Indicators
USB Port (charge battery)
Console Port
Connect PPM- to PC by console cable. Run HyperTerminal 1000 in
Windows at 38400 bps (Baud Rate) to connect and open the default
settings. Press Ctrl+C to enter main menu. Select A to check
firmware version B to update firmware with using X modem or
protocol.
PWR/TEST LED
When test is started, PWR/TEST LED is blinking orange
When test is finished, PWR/TEST LED keeps orange
When test is finished ready for next test, PWR/TEST LED
keeps green
WATT/VDC LED
When LED is in green, the 3-digit LED display shows the
PoE power in unit of Watt.
When LED is in orange, the 3-digit LED display shows the
PoE DC voltage.
When LED is off and Normal/Alarm LED is , the green
3-digit LED display shows the value of temperature.
OK/NG LED
When LED is in green, it indicates the power from PSE is
able to provide the desire maximum power to PD.
When LED is in orange, it indicates the power is not
enough to support the desire maximum power to PD.
When LE is in , the measurement is D blinking orange
failed and the Current is too high (over 2A).
When LED is off and Normal/Alarm LED i , the s in orange
measurement is failed and the device is over-temperature
(over ). 100℃
Normal/Alarm LED
When LED is in green, the LED digits display shows the
value of temperature
When LED is in orange, the device is over-temperature
(over 100℃).
Measurement Procedures
Hardware connection
Screw tightly the battery pack and connect the cable
as the illustration. Switch power on at the bottom.
For cable bare wires, these can be clamped into
Power Probing Terminal directly for Mode A (Power via
Pin 1, 2, 3, 6) or Mode B (Power via Pin 4, 5, 7, 8) of
IEEE802.3af standard.
Note: Network cable can not be connected to UTP port
and Power Probing Terminal simultaneously.
Operation Procedure
1. To set desire maximum power from PS to PD for test. E
Push and hold Start/Set(-) Button for 3 seconds to enter for configuration of maximum power limit It confirms with a beep .
sound and the 3-dig LED display start blinking. Press the it Start/Set(-) Start/Set(-) or buttons to set the desired power limit
Then, push and hold Start/Set(- button for 3 seconds to exit the configuration stag) e.
2. Press Start/Set(-) Button to start power measurement st. te
The will start , and the 3-digit LED display will show the changing power measurement. After PWR/TEST LED orange blinking
the test is done, i the is , it indicates that the power from PSE could support the desire maximum powerf OK/NG LED green ON .
If the OK/NG LED is , it indicates that the power from PSE could support the desire maximum power. orange ON NOT
Note that if - is over 50 the test will be prohibited Wait till it cools down for normal start. Once it starts testing, the PPM 1000 °C, .
tolerated temperature will be up to 100 °C.
3. Press to show the real-time value or measurement resultDisplay/Set(+) Button s.
Show value of measurement results while the is after test. PWR/TEST LED orange
Press once to show the value of power measurement when the Display/Set(+) Button WATT/VDC LED is . green
Press again to show the value of DC voltage when the Display/Set(+) Button WATT/VDC LED is . orange
Press again to show the device temperature when the is Display/Set(+) Button Normal/Alarm LED green.
Show real-time value (by pressing Start/Set(-) Button PWR/TEST LED) while the is green.
Press once to show the value of power measurement when the Display/Set(+) Button WATT/VDC LED is green.
Press again to show the value of DC voltage when tDisplay/Set(+) Button he WATT/VDC LED is orange.
Press again to show the device temperature when the is . Display/Set(+) Button Normal/Alarm LED green
4. Alarm notification
When Normal/Alarm LED , it indicates that PPM- is over-temperature (over Please stop the is orange ON 1000 100℃).
measurement until e device i cool down below 50 . th s °C
Specifications
Detection Range:
Watt: 0~96W
Voltage: ~60V (Over V is 24 40
required initially.)
Current: 0~2A
Power:
External Battery Pack
Provide 7 hours of standby time, shorter if
operations k going. eep
Overload Protection:
Operation Temp:
Humility:
Polyswitch over current protection
- ~ 20°C 50°C
0% ~ 85% RH
Battery
Pack:
Li-Ion, 2,400 mAh, 3.7 V,
Charged by USB cable
Charge Time: 3~4 hours

Produktspecifikationer

Varumärke: LevelOne
Kategori: Kablar för PC och kringutrustning
Modell: PPM-1000

Behöver du hjälp?

Om du behöver hjälp med LevelOne PPM-1000 ställ en fråga nedan och andra användare kommer att svara dig


Kablar för PC och kringutrustning LevelOne Manualer

LevelOne

LevelOne PPM-1000 Bruksanvisning

20 Augusti 2024

Kablar för PC och kringutrustning Manualer

Nyaste Kablar för PC och kringutrustning Manualer

Simplified MFG

Simplified MFG EXUSB3.0 Bruksanvisning

10 Januari 2025
Eminent

Eminent EM8660 Bruksanvisning

8 Januari 2025
Pioneer

Pioneer CD-SVW-UAR.006AE Bruksanvisning

4 Januari 2025
Roline

Roline 11.04.5681 Bruksanvisning

3 Januari 2025
Roline

Roline 14.01.3416 Bruksanvisning

3 Januari 2025
Roline

Roline 11.09.4276 Bruksanvisning

3 Januari 2025
UNITEK

UNITEK V1423A Bruksanvisning

3 Januari 2025
ATen

ATen KA7570 Bruksanvisning

2 Januari 2025
Tripp Lite

Tripp Lite N252-048-1U Bruksanvisning

31 December 2025
Tripp Lite

Tripp Lite N044-000-R Bruksanvisning

31 December 2025