Lindell Audio LiN2A Bruksanvisning

Lindell Audio Kompressor LiN2A

Läs nedan 📖 manual på svenska för Lindell Audio LiN2A (2 sidor) i kategorin Kompressor. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
©2022 Lindell Audio. This manual and any associated intellectual property are subject to copyright protection. No part
of this document may be reproduced in any form without explicit written consent from Lindell Audio. Lindell Audio is
a RAD Global Distribution company.
LiN2A
Vintage Leveling Amplier
Specications
Attack Dictated by T4BLA optocell
Release Dictated by T4BLA optocell
Ratio Program-dependant
Gain Up to 40 DB ±1DB
Voltage 115VAC, 230VAC rear panel switchable AC Mains Input: IEC320-C14 standard plug.
AC Mains Input 100V-240V depending on supplied
Dimensions Width 438mm (19”)
Height 88mm (2U)
Depth 250mm
1. Read these instructions.
2. Keep these instructions
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus that produce heat.
9. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they
exit from the apparatus. If the power cord
becomes frayed, stop using immediately.
10. Use only attachments/accessories specied
by the manufacturer
11. Use only with a cart, stand, tripod, bracket
or table specied by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms
or when unused for long periods of time.
13. Refer all servicing to qualied service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
14. This apparatus shall not be exposed to
dripping or splashing, and no object lled with
liquids, such as vases, shall be placed on the
apparatus.
15. Note that this apparatus is not completely
disconnected from the AC mains service when
the power switch is in the OFF position.
16. The mains plug or power inlet on the product
is used as the disconnect device, so the
disconnected device shall remain readily
operable when reconnected.
17. Any changes or modications not expressly
approved in this manual could void your
authority to operate this apparatus.
Important !
Be sure to only use the supplied 3-prong
IEC cable provided with this unit.
The triangular lightning ash icon is in-
tended to alert the user to the presence
of uninsulated, dangerous voltage within
Quick Start Guide
1. Mute your studio monitors.
2. Connect your LiN2A to your mixing bus or
patch bay then using balanced TRS cables.
3. Set all controls fullly counter-clockwise.
4. Set the switch to ON, and apply power. Power
Power LED meter will light up.
5. Unmute your monitors, and verify that signal
is passing to and from the unit.
6. Set the and controls to Gain Peak Reduction
about 12 o’clock, and set the to Meter mode
Gain Reduction. Increase the Input until the
meter is deecting a few dB.
7. Once again verify signal is passing through the
unit. If so, the unit is functioning correctly.
Basic Use
Use the control to set the desired Peak Reduction
amount of compression. Higher Peak Reduction
settings will result in a quieter signal; use the Gain
control to compensate for this loss. Try to match
the original level as closely as possible for A/B
comparisons that aren’t colored by differences in
overall volume.
Compression Modes
• Compress: A gentler compression setting of
roughly 3:1. Note that in the ‘2A compression
style, compression is variable depending on
the dynamic range of the program material.
Higher Peak Reduction values result in slight-
ly higher compression ratios.
• Limit: A hard limiter with a ∞:1 ratio.
What about Attack/Release?
Part of the allure of ‘2A-style compression is its
ease of use, thanks in no small part to its hard-
wired attack and release settings. Expect it to
sound great with no fuss.
Attack time is incredibly fast at around 10 milli-
seconds. About 1/40th the time it takes to blink.
Release time is dependent opon the amount of
compression applied by the conPeak Reduction -
trol, and can range anywhere from half a second
to ve seconds for total release.
Meter Calibration
Making sure that the meter returns to zero is im-
portant to the Lin2A’s functionality. This is con-
trolled the the master calibration set screw on the
back of the unit.
To calibrate, set the to Gain Metering Mode
Reduction and ensure that no audio is passing
through the unit. Then, using a athead
screwdriver, rotate the screw on the rear panel
until the needle rests on 0.
Voila! Meter calibrated.
The T4BLA Optocell
The LiN2A features a custom-designed Black Lion
Audio T4BLA Optocell. It yields sublime transpar-
ency and smooth gain reduction due to highly
selective trimming of its photocell.
1. Power Button: turns the Lin 2A
on/off.
2. Mode: Sets Lin2A to Limit or
Compress mode.
3. Gain: Sets the post-compression
make-up gain to compensate for
level lost during compression
4. VU Meter: Displays units select-
ed by Meter Mode.
5. Peak Reduction: Sets the de-
sired amount of compression/
limiting.
6. Meter Mode: Sets the type of
information rendered on the
meter. Gain Reduction meters
the amount of gain reduction ap-
plied. and Output +10 Output
+4 will render the Output level
as respectively described.
7. : ONLY use the AC Power Input
supplied IEC Cable to power this
unit.
8. Voltage setting: Select the volt-
age suitable to your region. Do
not power the Lin-2A by inap-
propriate voltage.
9. Grounding plug: The unit
should only be used in a prop-
erly-grounded studio. Do not de-
feat the third-pin ground for use
in an ungrounded studio.
10. Meter Calibration: Use this con-
trol to adjust the 0 resting point
when no compression is being
applied.
11. TRS Output: Balanced line-level
output.
12. TRS Input: Balanced line-level
input.
Note: For proper
performance, balanced
TRS must be used for all
inputs and outputs.
Important Safety Instructions
the product’s enclosure that may be of
sufcient magnitude to constitute a risk of
electric shock.
The triangular exclamation point icon is
intended to alert the user to the presence
of important operating and maintenance
(servicing) instructions in the literature ac-
companying the product.
The Lindell Audio LiN2A complies with all
applicable RoHS / WEEE European Union
directives.
Do not attempt to service this unit yourself,
as it will void your warranty. Please check
your unit carefully upon receipt and return
to place of purchase immediately if there
are any problems with the product. After
that, the standard Lindell Audio 1 YEAR
warranty will apply to defects in materials
and workmanship.
International Service
For service or warranty assistance, please
contact the Lindell Audio distributor in your
country through the dealer from whom you
purchased this product.
Limited One-Year Warranty
Lindell Audio’s LiN2A is warranted by Lin-
dell Audio to be free from defects in ma-
terials and workmanship for the period of
ONE (1) YEAR to the original purchaser. In
the event of such defects, the product will
be repaired without charge or, at our op-
tion, replaced with a new one if delivered to
Lindell Audio prepaid, together with a copy
of the sales slip or other proof of purchase
date. The warranty excludes problems due
to normal wear, abuse, shipping damage
or failure to use the product in accordance
with the specications.
All parts and labor are covered under this
Limited Warranty. However, if it is deter-
mined by Lindell Audio that the device was
damaged or made defective through abuse,
we reserve the right to charge the customer
for the cost of the repair.
Lindell Audio shall not be liable for damag-
es based upon inconvenience, loss of use
of the product, loss of time, interrupted
operation or commercial loss or any other
damages, whether incidental, consequen-
tial or otherwise. This warranty gives you
specic legal rights, and you may have oth-
er rights, which will vary from state to state.
This warranty is not transferable.
2 3 4 5 6
9
11
10
8
1
7
12

Produktspecifikationer

Varumärke: Lindell Audio
Kategori: Kompressor
Modell: LiN2A

Behöver du hjälp?

Om du behöver hjälp med Lindell Audio LiN2A ställ en fråga nedan och andra användare kommer att svara dig


Kompressor Lindell Audio Manualer

Lindell Audio

Lindell Audio LiN2A Bruksanvisning

30 Augusti 2024

Kompressor Manualer

Nyaste Kompressor Manualer

Nilfisk

Nilfisk VHC200 Bruksanvisning

27 Oktober 2024
Senco

Senco PC1251 Bruksanvisning

21 Oktober 2024
Einhell

Einhell TC-AC 420/50/10 V Bruksanvisning

21 Oktober 2024
Hyundai

Hyundai HY3200S Bruksanvisning

21 Oktober 2024
MSW

MSW -SPS-24 Bruksanvisning

15 Oktober 2024
MSW

MSW -UVRSRI Bruksanvisning

15 Oktober 2024
Ferm

Ferm CRM1027 FCO-1524 Bruksanvisning

13 Oktober 2024
Ferm

Ferm SGM1011 Bruksanvisning

9 Oktober 2024
Ozito

Ozito ACP-2115K Bruksanvisning

9 Oktober 2024
Metabo

Metabo EC 2510E Bruksanvisning

3 Oktober 2024