Lindell Audio LiN76 Bruksanvisning

Lindell Audio Processor LiN76

Läs nedan 📖 manual på svenska för Lindell Audio LiN76 (2 sidor) i kategorin Processor. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

protection. No part of this document may be reproduced in any form without explicit written

consent from Lindell Audio. Lindell Audio is a RAD Global Distribution company.

LiN76

Vintage Limiting Amplier

Specications

Attack Continuously variable 20uS to 800uS

Release Continuously variable 50mS to 1200mS

Ratio Pushbutton selected 4:1, 8:1, 12:1, 20:1 and any combination

Voltage 12VAC

AC Mains Input 100V-240V depending on supplied

Dimensions Width 438mm (19”)

Height 88mm (2U)

Depth 250mm

Weight 8kg

1. Read these instructions.

2. Keep these instructions

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such

as radiators, heat registers, stoves, or other

apparatus that produce heat.

9. Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they

exit from the apparatus. If the power cord

becomes frayed, stop using immediately.

10. Use only attachments/accessories specied

by the manufacturer

11. Use only with a cart, stand, tripod, bracket

or table specied by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

12. Unplug this apparatus during lightning storms

or when unused for long periods of time.

13. Refer all servicing to qualied service

personnel. Servicing is required when

the apparatus has been damaged in any

way, such as power supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

14. This apparatus shall not be exposed to

dripping or splashing, and no object lled with

liquids, such as vases, shall be placed on the

apparatus.

15. Note that this apparatus is not completely

disconnected from the AC mains service when

the power switch is in the OFF position.

16. The mains plug or power inlet on the product

is used as the disconnect device, so the

disconnected device shall remain readily

operable when reconnected.

17. Any changes or modications not expressly

approved in this manual could void your

authority to operate this apparatus.

Important !

Be sure to only use the supplied 12V AC supply

with this unit. Other supplies can potentially

damage the unit.

The lightning ash with an arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated “dangerous

Quick Start Guide

On your sound system, mute your monitors and

then using balanced TRS cables, connect your

LiN 76 to your mixing bus or patch bay. Set all

controls to full counter-clockwise position, and

all pushbuttons deselected or in the off position

make sure that no ratios are selected. Set the

OFF button to the deseleted (vu meter will

turn on) position, and apply power. Unmute

the monitors, and verify that signal is passing to

and from the unit. Set the Input, Output, Attack

and Release controls to about 12 o’clock, select

Ratio 4, and press the GR pushbutton. Increase

the Input until the meter is deecting a few

dB. Again, verify signal is passing through the

unit. At this point that the unit is functioning

correctly. If you would like the compressor to

compress more increase the input knob. This

will allow more signal into the compressor

and cause the compressor to react more. If you

would like the compressor to compress more

with the same amount of signal input, increase

the ratio. Ratios can be selected by pressing one

button at a time OR combinations of different

buttons at the same time.

All Button Mode

By pressing in all 4 buttons you active what

is referred to as “all button” mode. This “secret

mode” changes the ratio to roughly 20:1. It also

changes the bias of the circuit and the way that

the knobs interact with each other. The unit will

become much more aggressive with its reaction

knee becoming more like a plateau than a gentle

curve and will have a more aggressive dirty tone

that sounds incredible on aggressive drums. The

attack will become very punchy with a gooey

“sucking” sound on the release.

Favorite Setting

While there is no proper way to use a

compressor (please experiment and get

creative!) there are certain settings that we do

personally suggest for certain sources. The

most popular use would be vocals and we nd

that a relatively mild input signal of about 36-

30 should cause gentle compression for vocals,

creating a thickening effect without crushing

the audio. Then use the output control to bring

the vocals back up to the orginal volume level.

Setting the attack to roughly 9 o’clock and the

release to about 3 o’clock with give it a natural

sound without sounding articial.

Meter Calibration

Making sure that the meter returns to zero is

important to the compressors functionality.

This is controlled the the mater calibration set

screw on the back of the unit. Set the meter to

GR and make sure that no ratios are selected by

pressing in any ratio button just enough that all

4 pop out. Then using a athead screwdriver,

rotate the screw on the rear panel until the

needle rests on 0. Voila! Meter calibrated.

1. Power Button: turns the unit off.

When gr, +4 or +8 are selected,

the unit is on.

2. Input: Sets the threshold and

controls the level at which the

compressor starts compressing.

Louder signal will require less in-

put to trigger the same amount

of compression than softer

sounds.

3. Output: Applies makeup gain to

compressed signal to compen-

sate for signal lost during com-

pression

4. Attack: Controls the amount of

time it takes for the unit to react

to an incoming signal. Contin-

uously variable from 20uS to

800uS

5. Release: Controls the speed at

which the compressor releases

the compressed signal. Contin-

uously variable 50mS to 1200mS

6. Ratio: Controls the amount of

compression applied (Yes, it does

all-buttons-in-mode). The higher

the ratio, the more compression

is applied for the same amount

of signal inputted once compres-

sion is triggered.

7. VU Meter: Displays units select-

ed by Meter Mode.

8. Meter Mode: Selector switches

GR meters the amount of gain

reduction applied (+4 meters

output level at 0 with +4dB out-

put; +8 meters output level at 0

with +8dB output)

9. AC Adapter Input: ONLY use

the supplied 12VAC to power

this unit.

10. Meter Calibration: Use this con-

trol to adjust the 0 resting point

when no compression is being

applied.

11. TRS Output: Balanced line-level

output

12. TRS Input: Balanced line-level

input.

Note: For proper

performance, balanced

TRS must be used for all

inputs and outputs.

Important Safety Instructions

voltage” within the product’s enclosure that may

be of sufcient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral triangle

is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

product.

The Lindell Audio LiN 76 complies with all

applicable / RoHS / WEEE European Union

directives.

Do not attempt to service this unit yourself, as it

will void your warranty. Please check your unit

carefully upon receipt and return to place of

purchase immediately if there are any problems

with the product. After that, the standard Lindell

Audio 1 YEAR warranty will apply to defects in

materials and workmanship.

International Service

For service or warranty assistance, please

contact the Lindell Audio distributor in

your country through the dealer from

whom you purchased this product.

Limited 1 Year

Warranty

Lindell Audio’s LiN76 is warranted by Lindell

Audio to be free from defects in materials and

workmanship for the period of ONE (1) YEAR to the

original purchaser. In the event of such defects,

the product will be repaired without charge or, at

our option, replaced with a new one if delivered

to Lindell Audio prepaid, together with a copy of

the sales slip or other proof of purchase date.

The warranty excludes problems due to normal

wear, abuse, shipping damage or failure to use

the product in accordance with the specications.

All parts and labor are covered under this Limited

Warranty. However, if it is determined by Lindell

Audio that the device was damaged or made

defective through abuse, we reserve the right to

charge the customer for the cost of the repair.

Lindell Audio shall not be liable for damages based

upon inconvenience, loss of use of the product,

loss of time, interrupted operation or commercial

loss or any other damages, whether incidental,

consequential or otherwise. This warranty gives

you specic legal rights, and you may have other

rights, which will vary from state to state.

This warranty is not transferable.

2 3 4

9 10 11

6 8

5 1

Produktspecifikationer

Varumärke:	Lindell Audio
Kategori:	Processor
Modell:	LiN76

Behöver du hjälp?

Om du behöver hjälp med Lindell Audio LiN76 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Processor Lindell Audio Manualer

Lindell Audio LiN76 Bruksanvisning

27 Augusti 2024

Processor Manualer

Nyaste Processor Manualer

Toa DP-K1 Bruksanvisning

21 Oktober 2024

Eventide UltraTap Bruksanvisning

2 Oktober 2024

Rupert Neve Designs Portico II Bruksanvisning

27 September 2024

Helix DSP ULTRA Bruksanvisning

26 September 2024

Helix DSP.3S Bruksanvisning

26 September 2024

Helix DSP ULTRA S Bruksanvisning

26 September 2024

MyMix RX-2 Bruksanvisning

25 September 2024

Henry Engineering AES DigiSwitch 3X1 Bruksanvisning

25 September 2024

SPL Transient Designer 9946 Bruksanvisning

25 September 2024

SPL M/S Master Bruksanvisning

25 September 2024