Louroe Electronics AOP-SP-PB Bruksanvisning

Louroe Electronics Intercomsystem AOP-SP-PB

Läs nedan 📖 manual på svenska för Louroe Electronics AOP-SP-PB (4 sidor) i kategorin Intercomsystem. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
DESCRIPTION
AOPSP-PB
PLASTIC BACKBOX
(FLUSH MOUNT)
METAL BACKBOX
(SURFACE MOUNT)
OPERATIONS
Model AOPSP-PB is a wall mount two-way call stations containing a built-in line level electret condenser microphone, a
4” speaker and a 5/8 vandal resistant call button. It is designed to interface with various modes of audio/video
transmission systems such as:
IP Network Cameras
DVR’s
Video Servers
PC Soundcards
Provided with the unit are two back boxes for either flush or surface mounting to a wall. Also, a built-in call button
provides switch closure activation with the receiving device. a 12Vdc power supply is included with the the unit.
The gain of the microphone and speaker are factory adjusted. If it is necessary to change the gain of either or both the
audio output of the microphone and speaker of the unit, it has to be done in small increments. For adjusting the gain of
the microphone, rotate clockwise to increase or counterclockwise to decrease, the potentiometer marked “MIC” slowly
until the desired level is attained. Somebody at the head-end has to listen to it while the adjustments are made. If the
microphone’s gain is too high, it will attenuate the audio output of the speaker. The output of the speaker will then be
cutting off as you talk. If this happens, rotate the potentiometer marked “MIC” slowly counterclockwise to decrease the
gain of the microphone until the talkback sound at the speaker no longer cuts off.
To adjust the audio output of the speaker, rotate the “SPKR” potentiometer clockwise (increase) or counterclockwise
(decrease) slowly until the desired loudness is attained. If the audio from the microphone starts to get low, rotate the
“SPKR” potentiometer counterclockwise a small increment at a time until the microphone audio becomes louder again.
This unit has a built-in muting system that if the microphone’s is too high it is going to mute the speaker and vice versa.
aopsp-pb_inst 3/15
Page 1 of 4
AOPSP-PB
SPEAKERPHONE WITH CALL BUTTON
INSTALLATION AND OPERATING INSTRUCTIONS
6955 VALJEAN AVE, VAN NUYS, CA 91406
PH: (818)994-6498 / FAX: (818)994-6458
/ www.louroe.com
techsupport@louroe.com
®
WIRING CONNECTION TO SPEAKER AND MICROPHONE OF AOPSP-PB
Connect the two wires (black and green) attached to Call Button Switch to the contacts of the
receiving device, using wire nuts and 22 gauge stranded wire. Refer to the receiving device
manufacturers instructions for proper connection.
Page 2 of 4
LOUROE ELECTRONICS® 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
website: www.louroe.com e-mail: sales@louroe.com
(818)
INSTALLATION AND OPERATING INSTRUCTIONS
WIRING CONNECTION TO AOPSP-PB CALL BUTTON
aopsp-pb_inst 3/15
Drill an opening top, bottom or back side
of backbox for passing wiring or for
connecting conduit.
block marked A, B, C, SP
A = 12Vdc power
B = Audio output
C = Ground (bare wire)
SP = Speaker Connection
Bring one end of recommended cable and connect as follows:
Located on the bottom right side of PC board is a 4-pin terminal
1) Connect RED wire to terminal marked “B”
2) Connect BLACK wire to terminal marked “C” (together with bare wire)
3) Connect BARE wire to terminal marked “C“
4) Connect WHITE wire to terminal marked “SP“
5) No connection on terminal “A”
WIRING REQUIREMENTS
3 Conductor consisting of:
+
2 Conductor , 20 gauge shielded
with 22 gauge drain
+
1 Conductor , 20 gauge unshielded
All in the same jacket
WIRING CONNECTION TO IP CAMERA OR DVR
POWER CONNECTION
Bring the other end of the cable to connector that matches the audio input
and outputs of the receiving devices
1) RED (positive audio) and BARE (ground) are soldered to the audio
connector (RCA, 3.5mm Mono or Stereo plugs). This connector goes
to the Audio input of the receiving device (IP Camera, DVR, etc)
2) WHITE (positive audio) and BLACK (ground) are soldered to the another
audio connector (RCA, 3.5mm Mono or Stereo plugs. This connector
goes to the Audio output of the receiving device (IP Camera, DVR,
etc).
The unit has a 2-pin terminal block for power connections marked 12Vdc
1) Connect the positive 12Vdc of the power supply (AD-1) to the terminal
marked +
2) Connect the negative or ground of the power supply to terminal marked
GRD
WIRING CONNECTION TO AOP-SP-PB
See connections on the next page
INTERCONNECTION DIAGRAM
CONNECTING LOUROE MODEL AOPSP-PB
DIRECTLY TO AN IP CAMERA, DVR,
VIDEO SERVER, ETC. USING 3-COND. SHIELDED CABLE
EXT
MIC SPKR +12Vdc
AUDIO
OUT
AUDIO
IN
A B C
TALKBACK
ADJUST
MIC
ADJUST
CA
SPB
LOUROE MODEL AOPSP-PB
WHITE (SP)
BLACK (C)
(C) BARE
(B) RED
TO AUDIO OUT OF IP CAMERA, DVR, ETC.
TO AUDIO IN OF IP CAMERA, DVR, ETC.
NOTE: BLACK AND BARE WIRES ARE COMMON GROUND
BARE (C)
BLACK (C)
RED (B)
4-PIN TERMINAL BLOCK IDENTIFIER OF AOPSP-PB (A,B,C,SP)
( ) B = Audio Output
( ) C = Ground (audio) and Ground (speaker) (black wire)
( ) SP = Speaker output
A = not used with this application
red
bare
white
West Penn 358
or equivalent
CA
SPB
WHITE (SP)
Audio Out
Audio Out Audio In
Audio In
Bare Wire
Red Wire
RCA CONNECTION
3.5mm MONO CONNECTION 3.5mm STEREO CONNECTION
White Wire
Black Wire
Black Wire
White Wire
Red Wire
Bare Wire
M
M
M
M
M
O
O
O
O
O
N
N
N
N
N
O
O
O
O
O
S
S
S
S
S
T
T
T
T
T
E
E
E
E
E
R
R
R
R
R
E
E
E
E
E
O
O
O
O
O
Audio Out
Audio In
Red Wire
Black Wire
White WireBare Wire
WIRING REQUIREMENTS
3 Conductor consisting of:
+
2 Conductor , 20 gauge shielded
with 22 gauge drain
+
1 Conductor , 20 gauge unshielded
All in the same jacket
CALL
BUTTON
ELECTRET
CONDENSER
MICROPHONE
TO SWITCH CLOSURE OF
AUDIO RECEIVING DEVICE
(refer to manufacturer’s
instructions for connection)
EXT
MIC SPKR
AUDIO
OUT
AUDIO
IN
AOP-XD is not used for this application.
+12Vdc,500mA power required
(AD-1 power supply included)
Connect to this 2-pin terminal block
12 Vdc power is required to connect the AOP-SP-E directly to
an IP camera or DVR such as AD-1 power supply.
Positive 12Vdc connects to terminal marked “+”
Negative 12 Vdc or ground
connects to terminal marked “GND”
(wire with white stripes)
+12Vdc
+
GND
Page 3 of 4
LOUROE ELECTRONICS® 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
website: www.louroe.com e-mail: sales@louroe.com
(818)
INSTALLATION AND OPERATING INSTRUCTIONS
WIRE
NUT
WIRE
NUT
aopsp-pb_inst 3/15

Produktspecifikationer

Varumärke: Louroe Electronics
Kategori: Intercomsystem
Modell: AOP-SP-PB

Behöver du hjälp?

Om du behöver hjälp med Louroe Electronics AOP-SP-PB ställ en fråga nedan och andra användare kommer att svara dig


Intercomsystem Louroe Electronics Manualer

Louroe Electronics

Louroe Electronics AOP-SP-PB Bruksanvisning

10 Mars 2025

Intercomsystem Manualer

Nyaste Intercomsystem Manualer

Philips

Philips WelcomeEye Wireless Bruksanvisning

14 Januari 2025
Philips

Philips WelcomeEye Connect Pro Bruksanvisning

14 Januari 2025
Hikvision

Hikvision DS-KIS604-P Bruksanvisning

7 Januari 2025
Pentatech

Pentatech VT35 Bruksanvisning

4 Januari 2025
Somfy

Somfy V500 Bruksanvisning

31 December 2025
Vimar

Vimar K40930 Bruksanvisning

30 December 2025
Akuvox

Akuvox MD06 Bruksanvisning

30 December 2025
Elcom

Elcom REN410X Bruksanvisning

29 December 2024
Pentatech

Pentatech DVT60M Bruksanvisning

22 December 2024
Pentatech

Pentatech TF04 Bruksanvisning

22 December 2024