Lowel Tota-Light Bruksanvisning

Lowel Lampa Tota-Light

Läs nedan 📖 manual på svenska för Lowel Tota-Light (4 sidor) i kategorin Lampa. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

Lowel Tota-light Instructions

The Lowel Tota-light® is a professional

lighting fixture. Read these

instructions and lamp manufacturer’s

warnings before operating.

■Not for household use,

use only for film, video or imaging purposes.

■Do not leave lit fixture unattended.

■Unplug lights when unattended or

when relamping.

■Make certain that lamp voltage

matches power source voltage.

The units use lamps of different voltages

(example: never connect a 120 volt lamp to

a 220/240 volt source).

■Units such as this emit considerable

light and heat and, if not properly used,

could be dangerous.

■The Protective Screen must be used

to protect people and property in the unlikely

event of a defective lamp exploding, which

can cause small fragments of hot glass &

filament to be scattered about.

■Tota-light should never be operated

with doors either closed or beyond the

below shown “safety stop” position.

■Open faced lights should not be

positioned extremely close to people.

Ultraviolet light ray emissions can cause dam-

age to the eyes and reddening of the skin. The

likelihood of either occurring is increased with

length of exposure, focus intensity and prox-

imity. As a result, lights should be kept away

from people. Bounce illumination also elimi-

nates this problem.

■Avoid aiming the light at,

or placing close to, people, delicate objects

or flammable materials.

■Do not interfere with ventilation

by covering the lights in any way.

■Never touch hot parts.

■Do not use near standing water.

■Lights should be operated with

lamp filament horizontal.

■Avoid mounting lights directly

over people unless secured with a safety

cord or cable.

Lowel F. C. at 10' (3 m)

Code Volts Watts °K Avg Life doors norm doors 180°

EHZ 120 300 2900 2000 hr 14 (149) 11 (122)

FDN 120 500 3200 400 hr 27 (295) 22 (235)

FCZ 120 500 3000 2600 hr 26 (280) 19 (200)

FCM/HIR* 120 650 3200 400 hr 60 (640) 45 (485)

(FWM)

EMD 120 750 3200 400 hr 41 (445) 34 (365)

EMF 220/240 800 3200 250 hr 45 (480) 34 (365)

General Warnings

Lamp/Beam Data Performance

Tota-light

Technical Data

Size closed: 2" x 3" x 11"

(5 x 7.6 x 27.9 cm)

Weight less cable: 1.3 lbs (595 g)

With 16' cable: 2.25 lbs (1.02 kg)

Max. wattage: 750w at 120v,

800w at 220/240v

Max. amperage: 6.25 at 120v

Beam control: door angle provides

vertical beam control

Fits on: studs 5/8" (1.59 cm) or smaller

Materials: primarily aluminum alloy

Cable: 16' (4.88 m) #18/3 wire

Switch: in-line

U.S. Patent: 3852582

Tota Lamps Replacement

Warning: Always unplug unit

before relamping.

■ Lamps must be operated at their

rated voltage. Avoid touching

“glass” with bare fingers,

use tissue or hand-

kerchief. Skin oil

on lamp glass

will focus heat

unevenly and

cause premature

lamp failure.

■ Insert lamp carefully, to avoid breaking

porcelain ends.

■ The tension springs of the Tota sockets A

are very stiff, remove and install lamps care-

fully with 2 hands to avoid damaging lamp.

The porcelain contact of the socket may occa-

sionally stick in its protective metal housing.

The contact can be freed by pushing against it

with a pencil or other suitable object.

■ Due to inconsistencies in lamp (bulb) pro-

duction, an individual lamp may function for

less than avg. rated life. Some lamp manufac-

tures are of better quality than others and may

provide longer life and better performance.

See Lowel Catalog or www.lowel.com

for complete technical data.

Attaching Tota

Protective Screen

Warning: Never operate light without

supplied Protective Screen.

After opening Tota-light reflector doors, push

long open edges of screen into slots between

open doors of

Tota-light. When storing

the screen protect from

bending which will

effect the proper fit.

Tota Operations

Tota Door

Operating Positions

Tota-light must be operated with

doors open.

Operating fixture with doors closed or partially

closed will cause serious damage to the

fixture and possible personal hazard.

AMaximum light intensity (total door angle

of 90°). Door handles will help prevent

doors from closing beyond the safe operating

position.

BMaximum vertical spread.

CCompensates for light fall-off when illumi-

nating a wall or cyc from below (opposite

door configuration when lighting from above).

A second

Tota stacks

on and locks

in place

Flexi-shaft locks

into mount to hold

flags and flectors

11” (29.9 cm) 2” (5 cm)

3” (7.6 cm)

360°

Constant

tension

no-yoke

tilting

Gull-wing

reflector produces

wide, smooth

light pattern

Adjustable

reflector can

actually

light behind

itself

Lock for

umbrella and

gel-frame

Slot for

umbrella and

gel-frame

Large cool

knob for

360° tilting

TOTA-LIGHT

TOTA-BR ELLA

TOTA-FRAME

4.5” (11.4 cm)

Safety stop/

reflector handle

• 750W max @ 120V.

• 800W max @ 220/240V.

• Tota and V-light lamps are not

interchangeable.

• Tota lamps are frosted except FCM/HIR

• *G.E. Watt Miser™, also known as FWM,

has virtually same output as 1000W lamp

(see manufacturers specifications).

Beam angles-points at which intensity drops

to 50% of maximum

With 120v, 750w, 3200°K, EMD lamp

NoYes

A B C

The following components are shared by both the

Tota and Omni-lights. Their attachment may differ

slightly between Tota and Omni, as described below.

Umbrellas

Photographic umbrellas

convert relatively hard

light sources, such as

spotlights, into relatively

soft sources that provide

soft shadows and high-

lights. Although not

appropriate for every

subject or mood, the

quality of light can be very beautiful. There are two Umbrellas

designed for use with the Tota lights, a woven, soft silver

Tota-brella (T1-25) and a softer white Tota-brella (T1-26) that

produces a softer light and also may be used as a large dif-

fuser. The larger Lowel DP Umbrellas (Silver D2-25, White

D2-26) may also be used with the Tota-lights (see below).

Warning:

When lights with umbrellas are extended very high, or used on

undersized stands or in areas of heavy “traffic”, it is advisable

to add weight (such as the Lowel weight) to the base of the

stand. This reduces the chance of lights falling over which

could damage the umbrella, the lamp, and possibly cause

personal injury.

Using Umbrellas with Tota

Insert umbrella through hole until shaft

appears through opposite hole. Lock with

knob. When the umbrella is in place, the

gel frame cannot be used. Tota-shades and

gels should be used for daylight correction.

The use of clear instead of frosted lamps

will increase the light output by approximately 15%. When

using the DP Umbrella, the tilt tension of the light may have to

be increased. This can be done easily by tightening the nut

located on the stand fitting with a 7/16" wrench.

Do not over tighten!

Tota-frame

Code: T1-20

Unfold frame, extending frame bar and insert

through front accessory mounting hole

until shaft appears through opposite

hole. Lock with knob.

Tota/Omni Gels

Gels are secured to the frame with

corner spring clips. Gels should not

be doubled up. Precut, tough, fade

resistant Lowel gels are available in

daylight blue, frost diffusion, and

neutral density. Gels can be cut

into various shapes to cover only

part of the frame and subject.

(See gel instruction sheet.)

Tota-flag & Tota-flector

Codes: T1-52 & T1-54

Tota flags can be used separately, or

snapped together end to end or side to

side. Flags can be attached to the light

with a flexi-shaft. Flags block or “feather”

light off background, subject, or camera

lens. Tota-flectors can be attached in the

same way and used to redirect some of

the light. It can also provide close-up fill

illumination from the sun or other source

over a small area. Slight convex bowing

of the surface will reduce the intensity

and increase the area illumination.

Avoid mounting flags or reflectors directly

over people unless secured with a safety

cord or cable.

Flexi-shaft

Code: T1-50 (set of 2)

A flexible arm positions Tota-flags and Tota-flec-

tors. The fixed end of the Flexi-shaft snaps into a

female connector on the Tota & Omni-lights, Tota-clamp and a

few other Tota components. The rotating end snaps on to the

flag, flector etc. Avoid overstressing connectors while bending

and twisting. Insert the non-rotating end into the light.

Tota-tatch

Code: T1-34

Spring clamp attaches Tota-flags and

Tota-flectors with or without Flexi-shafts,

to stands, pipes, and flat surfaces.

The snap-in fitting rotates to help

position flags. Tota-tatch may also be

used to hold and position black & white

cards, cue cards, gels, etc.

To Store Tota

When fixture is cool to the touch, disconnect

plug on rear of Tota-light. Remove

Protective Screen, spring out door

handles slightly until open end

can slip between double walls

and close doors. Store Protective

Screen “over” folded light. When

storing the screen, protect from

bending which will effect the

proper fit.

Storing Tota Tota Light Controls

Tota-shade

Codes: T1-21 (1)

T1-24 (set of 4)

Top/ Bottom Shades.

Attach Tota-shade panel to the top or bottom reflector door

with black clips facing in to

lock over the door's ribs.

Side Shades can be used

only when top and bottom

panels are attached. Turn

each black clip 45° and

attach one each to the bent

rod ends of the top and bot-

tom panels. Reflector doors

must be held tightly against

their 45° angle stops while

doing this.

Tota/Omni Shared Light Control Accessories

Lowel Tota-light Instructions

Lampaks provide transparent, semi rigid

foam filled storage for spare lamps.

Always remove lamps from fixture

& store in Lampak if the kit will be

travelling for an extended period

(example: flights or cargo).

Never put hot lamps in

Lampak.

Tota Lampak

Code: T1-61

Stores 6 Tota lamps in foam filled

plastic case. (lamps not included)

Tota/Omni Lampak

Code: TO-61

Stores 2 Tota & 4 Omni lamps in foam

filled plastic case. (lamps not included)

Lampaks

TOTA-LIGHT

TOTA-BRELLA

TOTA-FRAME

Panels become extremely hot; do not touch

with bare fingers. Do not close Tota-shade

when lamp is on.

Lowel Tota-light Instructions

The following components are shared

by both the Tota and Omni-lights.

Tota-mount

Code: T1-32

Tota-mount supports small fixtures atop

doors and partitions. Doors can be open or

closed. The light can be inside or outside

room, since swinging arm extends past most

door jams. Tota-mount can be flipped over

and nailed to studio set walls or Gaffer-taped

to windows or tile, wood, metal and other

wall surfaces. Tota-mount should not be

used with lights heavier than 3 lbs. (1.33 kg)

Mounting Tota-mount

with Gaffer Tape

Use 12"of Gaffer-tape on each bar of

Tota-mount or side of Vipod and burnish

down with a coin. Avoid wallpaper, soft

composition board or flaking paint. Never

attach to the ceiling with tape. Use original

Lowel Gaffer-tape, as many substitutes leave

adhesive residue or lack sufficient strength.

When properly attached, Tota-mount or Vipod

will support the Iight for days. However,

on dirty or poorly bonded surfaces, or with

improper or poorly applied tape, there is the

danger of the mount falling down and causing

serious damage. Check adhesion periodically.

Prevent direct light from overheating tape.

Remove tape when cool, by peeling back

diagonally. Tota-mount should never

be used with heavier lights.

Tota-daptor

Code: T1-35

Steps up undersize stand tops

to standard 5/8". It also acts as

a short extension. It has two

snap-in fittings for Flexi-shafts.

Two Tota-lights can be locked

together by turning one of the

stand fittings “backwards” and

locking it onto the stand fitting

extension. For each additional two Totas, a

Tota-daptor must be added. The stacked lights

can then be mounted on a stand or hung from

a suitable clamp. Care must be exercised to

provide sufficient ventilation and prevent

cables from contacting lights.

Scissor-mount

Code: CM-20

Attaches Tota-lights,

and Omni-lights to dropped ceiling:

Clamp X bars of grid lock to

T-Bar of ceiling frame at support

cable intersection. Attach fixture

to mount stud and tighten.

Omni-lights should also use the Tota-daptor

enabling the fixture to be turned “right side

up” (top of the light facing the ceiling).

Operating the Omni-lights upside down will

cause short lamp life. Avoid mounting fixtures

directly over people unless secured with a

safety cord or cable.

Tota/Omni Mounts Cables & Connectors

16' Tota/Omni Cable

Code: T1-80

Standard #18/3; with switch & Edison

wall plug.

16' (5 m) Tota Eurocord

Code: T1-801

#18/3 (.75 mm/3) with double pole switch

and male CEE-7 plug.

16' (5 m) Tota UK Cord

Code: T1-802

#18/3 (.75 mm/3) with double pole switch

and male fused BS 1363A plug.

10' Unswitched Cable

Code: T1-808

For portable stage lighting use.

“Hard service” #18/3 cable.

These accessories may also be

used, consult their instructions

for proper use.

Space-clamp

Interlink

Grip

Tota-light has a

constant-tension tilt

(torque) which can be

adjusted, if needed, by

tightening the nut located

on the stand fitting with a

7/16" wrench.

Reflector door tension can be adjusted by

tightening the screws located on the rear of

the reflector door with a screwdriver.

IGHT

TOTA-LIGHT

T OT A-BRELLA

T OT A-FRAME

Male

Female

16'

MaleFemale

16'

MaleFemale

16'

Male

Female

10'

Tota Adjustments

Omni-stand

Code: O1-33

Weight: 2.6 lbs

(1.2 kg)

Size: (2.74 m), 27"

(69 cm) folded

Sturdy and lightweight;

extends to 9'. Collar

clamping;

standard 5/8"

(1.59 cm) stud.

Uni TO Stand

Code: UN-55

Weight: 2.6 lbs (1.2 kg)

Size: 21.5" (54.6 cm) folded.

Maximum height:

7'11" (2.4 m)

Base diameter: 43"

New stand, based

on design

combination

of Uni-stand &

Omni-stand. More stable than

Uni-stand, more compact than

Omni-stand.

Tota-clamp

Code: T1-30

Tota-clamp supports most lights

that fit standard 5/8" studs.

Tota-clamp can be attached to

pipes, stands or flat surfaces.

When clamping on furniture,

use thin wood or cardboard to

avoid marring. To rotate stud,

turn wing nut counterclockwise

several turns. The stud can be

locked in any of four positions; two for the

5/8" stud and two for the end with the 1/4-20

tapped hole. A 1/4-20 screw can be used to

lock on some microphone yokes and various

accessories. Tota-clamp has two snap-in

fittings for Flexi-shafts.

Produktspecifikationer

Varumärke:	Lowel
Kategori:	Lampa
Modell:	Tota-Light

Behöver du hjälp?

Om du behöver hjälp med Lowel Tota-Light ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Lampa Lowel Manualer

Lowel Tota-Light Bruksanvisning

17 September 2024

Lampa Manualer

Nyaste Lampa Manualer

Hensel Expert D 500 Bruksanvisning

26 Oktober 2024

IKEA NYFORS 103.031.10 Bruksanvisning

26 Oktober 2024

IKEA VÅGHÖJD 705.204.36 Bruksanvisning

26 Oktober 2024

Philips LPL72X1 Bruksanvisning

24 Oktober 2024

IKEA SKINA Bruksanvisning

24 Oktober 2024

Philips PEN20 Bruksanvisning

24 Oktober 2024

ET2 Picolo E22271-75PC Bruksanvisning

23 Oktober 2024

Crystorama Hampton 5623-AB Bruksanvisning

23 Oktober 2024

Crystorama Sterling 7584-DT Bruksanvisning

23 Oktober 2024

Crystorama Westwood 2256-PN Bruksanvisning

23 Oktober 2024