M-Audio BX8 D3 Bruksanvisning

Läs nedan 📖 manual på svenska för M-Audio BX8 D3 (28 sidor) i kategorin Övervaka. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/28
User Guide
User Guide
User Guide
User Guide User Guide
English ( 2 – 6 )
Guía del usuario
Guía del usuario
Guía del usuario
Guía del usuario Guía del usuario
Español ( 7 – 11 )
Guide dutilisation
Guide dutilisation
Guide dutilisation
Guide dutilisationGuide dutilisation
Français ( 12 – 16 )
Guida per luso
Guida per luso
Guida per luso
Guida per luso Guida per luso
Italiano ( 17 – 21 )
Benutzerhandbuch
Benutzerhandbuch
Benutzerhandbuch
Benutzerhandbuch Benutzerhandbuch
Deutsch ( 22 – 26 )
Appendix
Appendix
Appendix
Appendix Appendix
English ( 27 )
2
MIC/LI NEMIC/LI NE
M-TRACK
2X2M
C -SERIES
User Guide ( )English
Introduction
Box Contents
BX8 D3
Power Cable
Acoustic Foam Pad
User Guide
Safety & Warranty Manual
Support
For the latest information about this product (documentation, technical specifications, system
requirements, compatibility information, etc.) and product registration, visit m-audio.com.
For additional product support, visit m-audio.com/support.
Setup
Connection Diagram
Items not listed under Introduction > Box Contents are sold separately.
Audio
Interface
Power
3
Features
Rear Panel
1. XLR Input: This jack accepts XLR input
connections with either balanced or
unbalanced wiring. The input wiring of an
XLR connector should be as follows:
XLR Pin 1: signal ground (shield)
XLR Pin 2: signal positive (+)
XLR Pin 3: signal negative (–)
2. TRS Input: This jack accepts 1/4" (6.35 mm)
connections with either balanced or
unbalanced wiring. For balanced wiring, a
three-conductor TRS plug is necessary. The
input wiring of a TRS connector should be as
follows:
TRS Tip: signal positive (+)
TRS Ring: signal negative (–)
TRS Sleeve: signal ground (shield)
3. Acoustic Space Switch: Your BX8 D3
monitors should ideally be placed at least
one foot away from the nearest wall, ceiling,
or other large, flat surface. However, this may
be impractical due to space limitations within
your studio. For that reason, BX8 D3
monitors feature an acoustic space switch.
This switch compensates for placement near
walls.
Tip: Be sure to leave at least 3" of space between the rear of the speaker and a wall to allow the
rear-firing port to "breathe" properly. Placing the speaker any closer than 3" may adversely
affect low-frequency response.
4. Sub-Frequency Vent Port: This port aids in reproduction of very low frequencies by
discharging frequencies below 60 Hz and to act as a cooling mechanism to prevent
overheating. This port should not be blocked.
5. Volume Control: Use the volume control to set the output from the BX8 D3 to proper levels as
required.
6. Power Switch: This switch turns the monitor on and off.
Note: This product does not have a standby/low-power mode.
7. Power Receptacle: Accepts a detachable 3-conductor IEC power cord in order to power the
monitor.
8. Fuse Holder: Holds the external main fuse.
9. Voltage-Select Switch: Provides two selections, 115V AC and 230V AC, and should be set to
match the "house supply" (receptacle) mains voltage of the country or location in which the
speaker is used. The 115V setting is correct for the USA, while the 230V setting is correct for
most of the UK and Europe.
1
2
2
2
22
4
4
4
44
5
5
5
55
6
6
6
66
7
7
7
77
9
9
9
99
8
8
8
88
3
3
3
33

Produktspecifikationer

Varumärke: M-Audio
Kategori: Övervaka
Modell: BX8 D3

Behöver du hjälp?

Om du behöver hjälp med M-Audio BX8 D3 ställ en fråga nedan och andra användare kommer att svara dig




Övervaka M-Audio Manualer

Övervaka Manualer

Nyaste Övervaka Manualer