Makita AF601 Bruksanvisning

Makita Häftapparat AF601

Läs nedan 📖 manual på svenska för Makita AF601 (12 sidor) i kategorin Häftapparat. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/12

INSTRUCTION MANUAL

Pneumatic Finish Nailer

AF601

ENGLISH: Original instructions

Read before use.

2 ENGLISH

SPECIFICATIONS

Model: AF601

Air pressure 0.49 - 0.83 MPa (4.9 - 8.3 bar)

Nail length 25 mm - 64 mm

Nail capacity 100 pcs.

Minimum hose diameter 6.5 mm

Pneumatic tool oil ISO VG32 or equivalent

Dimensions (L x W x H) 304 mm x 95 mm x 297 mm

Net weight 1.7 kg

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydifferfromcountrytocountry.

• WeightaccordingtoEPTA-Procedure01/2003

Symbols

Thefollowingshowthesymbolsusedfortheequip-

ment. Be sure that you understand their meaning before

use.

Read instruction manual.

Wear safety glasses.

Donotuseonscaffoldings,ladders.

Intended use

Thetoolisintendedforfasteningoninteriorworkand

furniture work.

SAFETY WARNINGS

Pneumatic nailer/stapler safety

warnings

WARNING: WARNING Read all safety warn-

ings and all instructions. Failure to follow the

warningsandinstructionsmayresultinseriousinjury,

electricshockand/orre.

Save all warnings and instruc-

tions for future reference.

For personal safety and proper operation and mainte-

nanceofthetool,readthisinstructionmanualbefore

using the tool.

General safety

Do not permit those uninstructed to use the tool.

2. No horseplay. Respect the tool as a working

implement.

3. Do not operate when under the inuence of

alcohol, drugs or the like.

4. Never alter the tool.

Personal protective equipments

1. Always wear safety glasses to protect your

eyes from dust or fastener injury.

WARNING: It is an employer's responsibility

to enforce the use of safety eye protection

equipment by the tool operators and by other

persons in the immediate working area.

For Australia and New Zealand only

Always wear safety glasses and face shield to

protect your eyes from dust or fastener injury.

Thesafetyglassesandthefaceshieldshould

conformwiththerequirementsofAS/NZS1336.

2. Wear hearing protection to protect your ears

against exhaust noise and head protection.

Also wear light but not loose clothing. Sleeves

should be buttoned or rolled up. No necktie

should be worn.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate the tool in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Operating the tool can

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating the tool. Distractions can cause you to

lose control.

4. Illuminate the work area sufciently.

There may be local regulations concerning

noise which must be complied with by keeping

noise levels within prescribed limits. In certain

cases, shutters should be used to contain noise.

3 ENGLISH

Safety devices

1. Make sure all safety systems are in working

order before operation. Thetoolmustnotoper-

ate if only the trigger is pulled or if only the contact

arm is pressed against the wood. It must work only

whenbothactionsareperformed.Testforpossible

faulty operation with fasteners unloaded and the

pusher in fully pulled position.

2. Do not play with the contact element: it pre-

vents accidental discharge, so it must be kept

on and not removed. Securing the trigger in the

ON position is also very dangerous. Never attempt

to fasten the trigger. Do not operate a tool if any

portionofthetooloperatingcontrolsisinoperable,

disconnected,altered,ornotworkingproperly.

3. Do not attempt to keep the contact element

depressed with tape or wire. Death or serious

injurymayoccur.

4. Always check contact element as instructed

in this manual. Fasteners may be driven acci-

dentally if the safety mechanism is not working

correctly.

Loading fasteners

1. Do not load the tool with fasteners when any

one of the operating controls is activated.

2. Use only fasteners specied in this manual.

Theuseofanyotherfastenersmaycausemal-

function of the tool.

Power source

1. Never connect the tool to compressed air line

where the air pressure can exceed the suitable

air pressure range of the tool, specied in the

"SPECIFICATIONS" table, by 10%. Make sure

that the pressure supplied by the compressed air

system does not exceed the suitable air pressure

range of the tool. Set the air pressure initially to

the lower value of the suitable air pressure range.

2. When using the tool operated by compressed

air, particular attention must be paid to avoid

exceeding the maximum allowable pressure.

3. Operate the tool at the lowest pressure

required for the application, in order to prevent

unnecessarily high noise levels, increased

wear and resulting failures.

4. Never use the tool with other than compressed

air.Ifbottledgas(carbondioxide,oxygen,

nitrogen,hydrogen,air,etc.)orcombustiblegas

(hydrogen,propane,acetylene,etc.)isusedasa

powersourceforthistool,thetoolwillexplodeand

causeseriousinjury.

5. Always disconnect the air hose and remove all

of the fasteners:

— when unattended;

— before performing any maintenance or

repair;

— beforecleaningajam;

— before moving the tool to a new location.

6. Use only pneumatic tool oil specied in this

manual.

Operational safety

1. Always check the tool for its overall condition

and loose screws before operation. Tighten as

required.

2. Handle the tool carefully, as there is high pres-

sure inside the tool that can be dangerous if a

crack is caused by rough handling (dropping

or striking). Do not attempt to carve or engrave

on the tool.

3. Stop the operation immediately if you notice

something wrong or out of the ordinary with

the tool. An improperly functioning tool must not

be used.

4. Do not point the ejection port at anyone in the

vicinity. Keep hands and feet away from the

ejection port area.

5. Always assume that the tool contains

fasteners.

6. Never point the tool toward yourself or anyone

whether it contains fasteners or not.

7. Do not rush the job or force the tool. Handle

the tool carefully.

8. Do not activate the tool unless the tool is

placed rmly against the workpiece.

9. Never hold or carry the tool with a nger on the

trigger or hand it to someone in this condition.

Accidentalringcancauseseriousinjury.

10. Never use fastener driving tools marked with

the symbol "Do not use on scaffoldings, lad-

ders" for specic application for example:

— when changing one driving location to

anotherinvolvestheuseofscaffoldings,

stairs,ladders,orladderalikeconstructions,

e.g. roof laths;

— closing boxes or crates;

— ttingtransportationsafetysystemse.g.on

vehicles and wagons.

11. Check walls, ceilings, oors, roong and

the like carefully to avoid possible electrical

shock, gas leakage, explosions, etc. caused by

striking live wires, conduits or gas pipes.

12.

Do not use the tool for fastening electrical cables.

It is not designed for electric cable installation and

may damage the insulation of electric cables thereby

causingelectricshockorrehazards.

13. Watch your footing and maintain your balance

with the tool. Make sure there is no one below

whenworkinginhighlocations,andsecuretheair

hosetopreventdangerifthereissuddenjerking

or catching.

14. On rooftops and other high locations, drive

fasteners as you move forward. It is easy to lose

your footing if you drive fasteners while inching

backward. When driving fasteners against perpen-

dicularsurface,workfromthetoptothebottom.

You can perform driving operations with less

fatigue by doing so.

15. A fastener will be bent or the tool can become

jammed if you mistakenly drive fastener on

top of another fastener or strike a knot in the

wood. The fastener may be thrown and hit

someone, or the tool itself can react danger-

ously. Place the fasteners with care.

16. Do not leave the loaded tool or the air com-

pressor under pressure for a long time out in

the sun. Be sure that dust, sand, chips and

foreign matter will not enter the tool in the

place where you leave it setting.

Produktspecifikationer

Varumärke:	Makita
Kategori:	Häftapparat
Modell:	AF601

Behöver du hjälp?

Om du behöver hjälp med Makita AF601 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Häftapparat Makita Manualer

Makita AT638 Bruksanvisning

2 Oktober 2024

Makita AN510H Bruksanvisning

12 September 2024

Makita AF506 Bruksanvisning

2 September 2024

Makita AT2550A Bruksanvisning

1 September 2024

Makita DBN600ZJ Bruksanvisning

1 September 2024

Makita AN613 Bruksanvisning

31 Augusti 2024

Makita AF601 Bruksanvisning

31 Augusti 2024

Makita T221DW Bruksanvisning

30 Augusti 2024

Makita T221D Bruksanvisning

27 Augusti 2024

Makita AN911H Bruksanvisning

18 Augusti 2024

Häftapparat Manualer

Nyaste Häftapparat Manualer

Einhell BT-EN 30 E Bruksanvisning

16 Januari 2025

Total TCBNLI2001 Bruksanvisning

17 December 2024

Whirlpool YWEE515S0LB Bruksanvisning

9 December 2024

Whirlpool YWEE515S0LV Bruksanvisning

9 December 2024

Sun Joe BDL-A0202 Bruksanvisning

7 December 2024

MSW -STAPLER 1500 Bruksanvisning

15 Oktober 2024

DeWalt DWFP71917 Bruksanvisning

1 Oktober 2024

Ryobi P322 Bruksanvisning

24 September 2024

Ryobi P318 Bruksanvisning

24 September 2024

Ryobi P317 Bruksanvisning

24 September 2024