Makita RP2302FC Bruksanvisning
Läs nedan 📖 manual på svenska för Makita RP2302FC (1 sidor) i kategorin Fräs. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000288 Rev01
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-228, SSM-228, SLB-228 and SLM-228 Interface Brackets
SSB-228, SSM-228, SLB-228 and SLM-228 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place nylon spacers on bottom of projector and align them with threaded inserts.
4. Place the interface bracket onto the bottom of the projector and align it with the holes in the bracket with the threaded inserts and nylon
spacers on the bottom of the projector.
5. Position M4 x 20mm pan head mounting screws with M4 washers, and M4 x 20mm flat head mounting screws into the mounting holes.
Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) Washer, Flat, M4
(4) 10-24 Thumb Nuts ** (3) Screw, Phillips Pan Head, M4 x 20mm
(1) All-Points Security Kit (2) Screw, Phillips Flat Head, M4 x 20mm
(5) Spacer, Nylon, .500 OD x.194 ID x .500
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-228 SLM-228
(Note: SSB-style interfac
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
N
o
t
e
:
S
S
M
-
s
t
y
l
e
i
n
t
e
r
f
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
Towards front of
projector
Towards front of
projector
Produktspecifikationer
| Varumärke: | Makita |
| Kategori: | Fräs |
| Modell: | RP2302FC |
Behöver du hjälp?
Om du behöver hjälp med Makita RP2302FC ställ en fråga nedan och andra användare kommer att svara dig
Fräs Makita Manualer
15 Oktober 2024
19 September 2024
19 September 2024
10 September 2024
4 September 2024
28 Juli 2024
Fräs Manualer
- Fräs Bosch
- Fräs DeWalt
- Fräs Alpina
- Fräs Ferm
- Fräs Gude
- Fräs Hitachi
- Fräs Black And Decker
- Fräs Vonroc
- Fräs Stanley
- Fräs Yato
- Fräs Parkside
- Fräs Worx
- Fräs Meec Tools
- Fräs Einhell
- Fräs Trend
- Fräs Maktec
- Fräs Bort
- Fräs Power Craft
- Fräs Powerplus
- Fräs Trotec
- Fräs Eibenstock
- Fräs Topcraft
- Fräs Texas
- Fräs Gamma
- Fräs Carat
- Fräs Flex
- Fräs Duro
- Fräs Mafell
- Fräs Truper
- Fräs Grizzly
- Fräs Kinzo
- Fräs Bruder Mannesmann
- Fräs Rupes
- Fräs Westfalia
- Fräs Holzmann
- Fräs Stomer
- Fräs Elu
- Fräs Triton
- Fräs Anova
- Fräs Rikon
- Fräs Felisatti
- Fräs Toledo
- Fräs CMT Orange Tools
Nyaste Fräs Manualer
28 December 2024
23 December 2024
15 Oktober 2024
4 Oktober 2024
26 September 2024
26 September 2024
25 September 2024
24 September 2024
23 September 2024
21 September 2024