Masport Westcott 2000 Bruksanvisning

Masport Värmare Westcott 2000

Läs nedan 📖 manual på svenska för Masport Westcott 2000 (8 sidor) i kategorin Värmare. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/8
Installation Instructions
Westcott 1000
Westcott 2000
Keep instructions for future reference
Glen Dimplex Australia proudly supports the activities of Landcare Australia through its membership of the AHHA
Version 1.2 2
1.0
IMPORTANT INFORMATION …………………….....
2
2.0
ASSEMBLY OF THE HEATER …………………………..
3
3.0
INSTALLING THE HEATER ………………………………
4
4.0
REDUCING CLEARANCES TO COMBUSTIBLES. ..
5
5.0
INSTALLING THE FLUE …………………………….…….
6
6.0
TECHNICAL DRAWINGS …………… …………..………
7
Most building regulatory Authorities in Australia require any
wood heater installation to comply with Installation Standard
AS/NZS 2918:20 . Different states and councils may have 18
varying regulations. Check local building regulations before
installing the appliance.
The Masport Westcott 1000 and 2000 wood heaters have
been tested to ensure that they will meet the appropriate
safety Standard requirements if the instructions in this manual
are followed. As the safety and emissions performance can be
affected by altering the appliance, no modifications are
allowed without written permission from the manufacturer.
WE RECOMMEND THAT THE INSTALLATION OF YOUR
MASPORT WOOD HEATER BE CARRIED OUT BY A QUALIFIED
INSTALLER.
WARNING: THE APPLIANCE AND FLUE SYSTEM SHALL BE
INSTALLED IN ACCORDANCE WITH AS/NZS 2918:20 AND 18
THE APPROPRIATE REQUIREMENTS OF THE RELEVANT
BUILDING CODE OR CODES.
WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH
THIS STANDARD SHALL COMPLY WITH THE REQUIREMENTS
OF AS/NZS 4012 & AS/NZS 4013 WHERE REQUIRED BY THE
REGULATORY AUTHORITY, I.E. THE APPLIANCE SHALL BE
IDENTIFIABLE BY A COMPLIANCE PLATE WITH THE MARKING
‘TESTED TO AS/NZS 4012 & AS/NZS 4013’.
ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN
APPROVED IN WRITING BY THE TESTING AUTHORITY IS
CONSIDERED TO BE IN BREACH OF THE APPROVAL GRANTED
FOR COMPLIANCE WITH AS/NZS 4012 & AS/NZS 4013.
CAUTION: MIXING OF APPLIANCE OR FLUE-SYSTEM
COMPONENTS FROM DIFFERENT SOURCES OR MODIFYING
THE DIMENSIONAL SPECIFICATION OF COMPONENTS MAY
RESULT IN HAZARDOUS CONDITIONS. WHERE SUCH ACTION IS
CONSIDERED, THE MANUFACTURER SHOULD BE CONSULTED
IN THE FIRST INSTANCE.
CAUTION: CRACKED AND BROKEN COMPONENTS, EG. GLASS
PANELS OR CERAMIC TILES, MAY RENDER THE INSTALLATION
UNSAFE.
1. IMPORTANT INFORMATION
TABLE OF CONTENTS
Version 1.2 3
To make the heater easier for handling on installation, remove
the baffle plate, side and back bricks and door. Please these in
a secure plate to avoid damage. These must be refitted after
installation.
The legs and other fixings are packed in the ashpan for safe
keeping in transport. Fix the legs to the underside of the
product using the bolts provided.
Packed with the heater is a heat shield to be fitted on the
underside of the product . After fitting the legs, fit the (Fig 1)
holes in the heat shield over the threaded ends that secure
the legs. Fasten the nuts over the heat shield to hold in place.
The primary air sealing plate is located on the front of the
grate. To locate in position, loosen the screws beneath the
grate and pull forward, then close the door fully, open again
and tighten the screws . (Fig 2)
Installing bricks and baffle
Before install the baffle plate and bricks, be sure to remove
the slotted log guard first otherwise baffle won’t fit through
door opening.
The baffle plate in the Westcott 1000 and 2000 models consist
of a steel retainer frame and a vermiculite board that sits in
the frame.
Position the rear vermiculite brick first positioning it below the
secondary burn tube. Fit the baffle plate (retainer and
vermiculite board) in the firebox. Hold the baffle plate up
while fitting the side vermiculite bricks and then rest the
baffle plate on top of the vermiculite side bricks.
To fit the log guard, there is a small square hole on each front
corner of the internal firebox that the legs on each end of the
log guard drop into to locate it.
Westcott 1000
Westcott 2000
2. ASSEMBLY OF THE HEATER

Produktspecifikationer

Varumärke: Masport
Kategori: Värmare
Modell: Westcott 2000

Behöver du hjälp?

Om du behöver hjälp med Masport Westcott 2000 ställ en fråga nedan och andra användare kommer att svara dig


Värmare Masport Manualer

Masport

Masport Rubyvale Bruksanvisning

8 September 2024
Masport

Masport R1500 Bruksanvisning

5 September 2024
Masport

Masport Riverstone Bruksanvisning

3 September 2024
Masport

Masport Pittsburgh MK II Bruksanvisning

2 September 2024
Masport

Masport Adena Bruksanvisning

30 Augusti 2024
Masport

Masport Rockwood Bruksanvisning

28 Augusti 2024
Masport

Masport Westcott 2000 Bruksanvisning

28 Augusti 2024
Masport

Masport Westcott 1000 Bruksanvisning

28 Augusti 2024
Masport

Masport Redwood Bruksanvisning

28 Augusti 2024
Masport

Masport Klondike Bruksanvisning

28 Augusti 2024

Värmare Manualer

Nyaste Värmare Manualer

Bestron

Bestron AFH211G Bruksanvisning

14 Januari 2025
Breville

Breville the Smart Tilt Control Max LCE308 Bruksanvisning

14 Januari 2025
Breville

Breville BodyZone BZB437 Bruksanvisning

14 Januari 2025
Duux

Duux Edge Oil Bruksanvisning

14 Januari 2025
Dimplex

Dimplex DX 521 Bruksanvisning

13 Januari 2025
Eurom

Eurom Fireball 60T Bruksanvisning

9 Januari 2025
Kambrook

Kambrook KFH600 Bruksanvisning

9 Januari 2025
Dimplex

Dimplex VF75A Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MG-QGW15-442A Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MH-2000WW Bruksanvisning

8 Januari 2025