Moxa NPort 5250A Bruksanvisning

Moxa Server NPort 5250A

Läs nedan 📖 manual på svenska för Moxa NPort 5250A (6 sidor) i kategorin Server. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/6

P/N: 1802052000014

*1802052000014*

NPort 5200A Series

Quick Installation Guide

Version 2.3, January 2021

Technical Support Contact Information

www.moxa.com/support



21 . A20 Moxa Inc ll rights reserved.

- - 2

Overview

NPort 5200A series of device servers are compact, palm-sized data

communication devices that allow you to control RS- 232 (NPort 5210A),

RS- -422/485 (NPort 5230A), and RS 232/422/485 (NPort 5250A) serial

devices over a TCP/IP based Ethernet.-

NOTE

“- T” indicates an extended temperature model.

Package Checklist

Before installing the NPort 5200A device server, verify that the package

contains the following items:

• 1 NPort 5200A serial device server

• - 4 stick on pads

• Quick Installation Guide

• Product Warranty Statement

Optional Accessory

• - - DK 35A: DIN Rail Mounting Kit (35 mm)

Notify your sales representative if any of the above items are missing or

damaged.

Hardware Introduction

As shown in the following figures, the NPort 5200A series device servers

have two male DB9 ports for transmitting RS-232 (NPort 5210A), or

RS- -232/422/485 (NPort 5250A) serial data and have two 5 pin terminal

block ports for transmitting RS- 422/485 (NPort 5230A).

Reset Button—Press and hold the Reset button for 5 seconds to load

factory defaults: Use a pointed object, such as a straightened paper clip

- - 3

or toothpick, to depress the reset button. This will cause the Ready LED to

blink on and off. The factory defaults will be loaded once the Ready LED

stops blinking (after about 5 seconds). At this point, release the reset

button.

LED Indicators—NPort 5200A’s top panel has four LED indicators, which

are described in the following table.

LED

Name

LED

Color

LED Function

Ready

R ed

Steady on:

Power is on and the NPort is booting up.

Blinking:

Indicates an IP conflict, or DHCP or BOOTP

server is not responding properly.

G reen

Steady on:

Power is on and the NPort is functioning

normally.

Blinking:

The NPort has been located by the NPort

Administrator’s Location function.

O ff

Power is off, or a power error..

Link

O range

10 Mbps Ethernet connection.

G reen

100 Mbps Ethernet connection.

O ff

Ethernet cable is disconnected.

P1, P2

O range

Serial port is receiving data.

G reen

Serial port is transmitting data.

O ff

No data is being transmitted or received through the

seri al port.

Adjustable pull high/low resistor and terminator for RS- 422/485

Remove the NPort 5230A/5250A’s top

cover and you will find DIP switches to

adjust each serial port’s pull

-high,

pull

low, and terminator. Do not use the 1

Ω -setting with RS

232 mode, as doing so

will degrade the RS

-232 signals and

shorten the communications range.

Pull- high resistor

Terminator

1 KΩ

120 Ω

OFF

*150 KΩ

*–

*Default

Produktspecifikationer

Varumärke:	Moxa
Kategori:	Server
Modell:	NPort 5250A
Typ av operation:	Draaiknop
Färg på produkten:	Black, Brushed steel
Inbyggd display:	Nee
Vikt:	3175 g
Bredd:	215.9 mm
Djup:	279.4 mm
Höjd:	431.8 mm
Förpackningens bredd:	254 mm
Djuppackning:	229 mm
Förpackningshöjd:	394 mm
Tillgångar:	600 W
Innehåll behållare/burk:	- l
Varierande hastighet:	Ja
Delar som tål diskmaskin:	Ja
Antihalkfötter:	Ja
Innehåller inte:	Bisfenol A / BPA
Pulsfunktion:	Ja
Mixerfunktioner:	Chop, Mixing, Puree
Spatel:	Ja
Degverktyg:	Ja
Inkluderar hackskiva:	Ja
Inkluderar julienneskiva:	Ja