Moxa SPL-24-T Bruksanvisning

Moxa Nätverkskort/adapter SPL-24-T

Läs nedan 📖 manual på svenska för Moxa SPL-24-T (7 sidor) i kategorin Nätverkskort/adapter. Denna guide var användbar för 16 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/7
P/N: 1802000240111
*1802000240111*
SPL 24 Series -
Quick Installation Guide
PoE Splitter
Vers 20ion 6.2 , May 21
Technical Support Contact Information
www.moxa.com/support
2 . A 20 1 Moxa Inc ll rights reserved.
- - 2
Overview
The SPL-24 plays the role of PD, and splits the data signal and power
signal that are transmitted from the PSE. The SPL-24 plays a dual role of
providing power to industrial devices, and enabling Ethernet connections.
The SPL- -24 have a wide operating temperature range of 40 to 75°C, and
are designed to withstand a high degree of vibration and shock. The
rugged hardware design makes the SPL-24 perfect for ensuring that your
Ethernet equipment can operate in critical industrial environments, such
as in hazardous locations, and complies with FCC and CE standards.
NOTE
Throughout this Hardware Installation Guide, we use EDS as an
abbreviation for Moxa EtherDevice Switch, and we use SPL as an
abbr
eviation for Moxa PoE Splitter:
SPL = Moxa PoE Splitter
Wiring Requirements
WARNING
Do not disconnect modules or wires unless the power supply has
been switched off or the area is known to be non
-
hazardous. The
devices may only be connected to the
supply voltage shown on
the type plate. The devices are designed for operation with a
Safety Extra
-
Low Voltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
Safety Extra
- Low Voltages (SELV) in compliance with IEC
60950-1/EN 60950-1.
WARNING
The power for this product is intended to be supplied by a Listed
Power Unit, with output marked LPS, and rated to deliver 48 VDC
at a maximum of 300 mA.
WARNING
This unit is a built
-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950
-1 -1 /EN60950
(or similar regulation).
- - 3
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your
Moxa EtherDevice Switch. Calculate the maximum
possible current in each power wire and common wire.
Observe
all electrical codes dictating the maximum current allowable for
each wire size. If the current goes above the maximum ratings,
the wiring could overheat, causing serious damage to your
equipment.
You should also pay attention to the following items:
• Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
in the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately.
• You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
• Keep the input wiring and the output wiring separated.
• It is strongly advised that you label the wiring to all devices in the
system when necessary.
Package Checklist for SPL-24
The Moxa SPL-24 is shipped with the following items. If any of these items
is missing or damaged, please contact your customer service
representative for assistance.
• - Moxa PoE Splitter, SPL 24
• i g Quick nstallation uide (printed)
• Warranty card
Features of SPL 24-
High Performance Network Switching Technology
• IEEE802.3af compliance
• - Power/data split from PoE lines using either spare pairs or data pairs
• Support for up to 12.95 W at 24 VDC
• Support for up to 15.4 watts per PoE port
• Short circuit protection
• Auto disconnection for over voltage or under voltage
• Power consumption detection and classification
Rugged Design
• Operating temperature range from 0 to 60°C, or extended operating
temperature from - - 40 to 75°C for “ T” models
• IP30, plastic case
• D - IN Rail or panel mounting ability

Produktspecifikationer

Varumärke: Moxa
Kategori: Nätverkskort/adapter
Modell: SPL-24-T

Behöver du hjälp?

Om du behöver hjälp med Moxa SPL-24-T ställ en fråga nedan och andra användare kommer att svara dig


Nätverkskort/adapter Moxa Manualer

Moxa

Moxa EPM-DK02 Bruksanvisning

11 September 2024
Moxa

Moxa EPM-3032 Bruksanvisning

11 September 2024
Moxa

Moxa EPM-DK01 Bruksanvisning

11 September 2024
Moxa

Moxa SPL-24-T Bruksanvisning

11 September 2024
Moxa

Moxa NA-4010 Bruksanvisning

11 September 2024

Nätverkskort/adapter Manualer

Nyaste Nätverkskort/adapter Manualer

StarTech.com

StarTech.com USB32HDVGA Bruksanvisning

15 Januari 2025
Martin Logan

Martin Logan WSK1D Bruksanvisning

14 Januari 2025
ZyXEL

ZyXEL WBE510D Bruksanvisning

14 Januari 2025
StarTech.com

StarTech.com 107B-USB-HDMI Bruksanvisning

14 Januari 2025
TP Link

TP Link UB500 Plus Bruksanvisning

3 Januari 2025
Digitus

Digitus DN-30211 Bruksanvisning

2 Januari 2025
Advantech

Advantech WISE-S100-A Bruksanvisning

1 Januari 2025
Edimax

Edimax EU-4307 V2 Bruksanvisning

30 December 2025
Digitus

Digitus DN-10110 Bruksanvisning

30 December 2025
D-Link

D-Link DFE-528TX Bruksanvisning

30 December 2025