Mtx Audio X1000D Bruksanvisning

Mtx Audio bilradio X1000D

Läs nedan 📖 manual på svenska för Mtx Audio X1000D (36 sidor) i kategorin bilradio. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/36

Owner's Manual

X1000D

Input/output panel layout

1. RCA input jacks – These RCA input jacks are for use with source units that have RCA or Line level outputs. A

source unit with a minimum level of 200mV is required for proper operation.

The use of high quality twisted pair cables is recommended to decrease the possibility of radiated noise entering

the system.

2. Speaker level inputs – This input will allow the ampliﬁer to operate from source units with speaker-level outputs.

Output speaker leads from the source unit should be tied directly to the wire harness provided with the ampliﬁer.

**Note: When speaker level inputs are used, a remote turn on wire must used to switch the ampliﬁer on and

off.**

3. Gain control – This control is used to match the input sensitivity of the ampliﬁer to the particular source unit

that you are using. The operating range varies from 200mV gain fully clockwise to 5V input gain fully counter

clockwise.

Introduction

Thank you for choosing an MTX XTHUNDER Ampliﬁer to power your car audio system. Each MTX XTHUNDER

ampliﬁer is CEA2006 certiﬁed which means you have a 100% guarantee that your ampliﬁer will deliver every Watt

it is rated at.

Speciﬁcations

Ratings:

• CEA2006 certiﬁed Power Output : 700 watts RMS at 4 ohm and ≤ 1% THD+N

• CEA2006 certiﬁed Power Output : 1000 watts RMS at 2 ohm and ≤ 1% THD+N

• Signal-to-Noise Ratio (1 watt) : >75dB

• THD+Noise (Distortion) (1 watt) : ≤ 1%

• Frequency Response (-3dB) : 20Hz-200Hz

• Maximum Input Signal : 5V

• Maximum Sensitivity : 200mV

• Dimensions : 315mm x 210mm x 50mm

• Crossover : Low pass 24dB 40Hz-200Hz

• Subsonic ﬁlter : variable 20Hz-50Hz

• High level input connection

X1000D - ampliﬁer owner's manual

www.mtx.com - www.mtxaudio.eu

4. Input selection switch - This switch, is used to match the ampliﬁer’s input to the source unit’s or DSP unit’s output.

If your source unit or DSP unit has a mono output you can select: Mono L or Mono R as your input connection,

if your source unit or DSP unit has a stereo output you need to select SUM for input now both RCA inputs of the

ampliﬁer are active and the stereo signal will be converted into a mono signal by the ampliﬁer.

5. EBC port - For connecting the included External Bass Control. A remote bass control so the bass can be adjusted

from the driver’s seat.

6. Subsonic ﬁlter control - This control is used to select the desired (high pass) subsonic ﬁlter frequency. The sub-

sonic ﬁlter protects the subwoofer(s) against too low frequencies that can dammage the subwoofer(s).

7. Low pass x-over frequency control - This control is used to select the desired low pass x-over frequency. The

frequency can be adjusted between 40Hz and 200Hz.

8. Speaker Terminals – Be sure to observe speaker polarity through the system. Failing to wire the speakers in

proper phase could result in a loss of bass response and/or poor

overall sound quality.

Caution : The X1000D ampliﬁer is not recommended for loads below 2 ohms.

9. Fuse - For convenience, all MTX XTHUNDER ampliﬁers utilize ATC type fuses. For continued protection in the

event that a fuse blows, replace the fuse only with the same value.

Caution : The power fuse on the amp is for protecting the amp against overdrive. To protect the vehicle’s electrical

system, an additional fuse is required within 30cm of the battery on the 12V+ cable.

10. Power Terminal – This is the main power input for the ampliﬁer and must be connected directly to the positive

terminal of the car battery for the ampliﬁer to operate properly. Use caution when running this cable through the

vehicule. Try to avoid running this cable along side the input RCA cables, antenna cabling, or other sensitive equi-

pment as the large amount of current ﬂowing through this cable can induce noise into your system. It is also very

important to have a tight connection to ensure maximum performance. We recommend to use 10mm2 or larger

power wire with the MTX XTHUNDER X1000D ampliﬁer.

11. Remote Terminal – The Ampliﬁer can be turned on by applying 12 volts to this terminal. Typically this voltage is

supplied by a wire from the source unit marked “remote” or “electric antenna”.

12. Ground Terminal – A good quality ground is required for your Ampliﬁer to operate at peak performance. A short

length of cable the same gauge as your power cable should be used to attach the ground terminal directly to the

chassis of the vehicle. Always scrape or sand any painted surfaces to expose bare metal where the ground wire

will attach.

Produktspecifikationer

Varumärke:	Mtx Audio
Kategori:	bilradio
Modell:	X1000D
Färg på produkten:	Zwart
Beeldscherm:	LED
Skärm diagonal:	27 "
Upplösning:	1920 x 1080 Pixels
Pekskärm:	Nee
Original bildförhållande:	16:9
Betraktningsvinkel, horisontell:	170 °
Betraktningsvinkel, vertikal:	160 °
Skärmform:	Flat
Typiskt kontrastförhållande:	1000:1
VGA (D-Sub) port(ar):	1
Antal HDMI-portar:	1
Monteringsalternativ för kabellås:	Nee
Inbyggda högtalare:	Ja
Genomsnittlig effekt:	2 W
Strömförbrukning (i standby):	- W
Strömförbrukning (max):	39.5 W
Antal högtalare:	2
Display, antal färger:	16.78 miljoen kleuren
HD typ:	Full HD
Ljudingångar:	Ja
Respons tid:	5 ms
Grafikupplösningar som stöds:	1920 x 1080 (HD 1080)
VESA montering:	Ja
Panelmonteringsgränssnitt:	100 x 100 mm
Ljusstyrka (typiskt):	300 cd/m²
Djup (utan bas):	61.66 mm
Höjd (utan bas):	396 mm
Bredd (utan bas):	648 mm
Vikt (utan bas):	7280 g
Enhetsbredd (med stativ):	648 mm
Djupenhet (med stativ):	212 mm
Enhetshöjd (med stativ):	479.1 mm
Kamfilter:	3D
BNC-ingångsportar:	2
AC-ingångsspänning:	100 - 240 V
AC-ingångsfrekvens:	50 - 60 Hz
Drifttemperatur (TT):	0 - 40 °C
Relativ luftfuktighet i drift (VV):	0 - 90 procent