Narva H7 Surefit Bruksanvisning

Läs nedan 📖 manual på svenska för Narva H7 Surefit (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/2
L.E.D SUREFIT GLOBES
Product Instructions
IS468 Issue 1: 20.03.20
Distributed by:
Brown & Watson Int. Pty. Ltd.
Knoxeld, Victoria 3180
www.narva.com.au
WARRANTY STATEMENT
Applicable only to product sold in Australia
Brown & Watson International Pty Ltd of 1500 Ferntree Gully Road, Knoxeld, Vic., telephone (03) 9730 6000,
fax (03) 9730 6050, warrants that all products described in its current catalogue (save and except for all bulbs
and lenses whether made of glass or some other substance) will under normal use and service be free of failures
in material and workmanship for a period of one (1) year (unless this period has been extended as indicated
elsewhere) from the date of the original purchase by the consumer as marked on the invoice. This warranty does
not cover ordinary wear and tear, abuse, alteration of products or damage caused by the consumer.
To make a warranty claim the consumer must deliver the product at their cost to the original place of purchase
or to any other place which may be nominated by either BWI or the retailer from where the product was bought
in order that a warranty assessment may be performed. The consumer must also deliver the original invoice
evidencing the date and place of purchase together with an explanation in writing as to the nature of the claim.
In the event that the claim is determined to be for a minor failure of the product then BWI reserves the right to
repair or replace it at its discretion. In the event that a major failure is determined the consumer will be entitled to a
replacement or a refund as well as compensation for any other reasonably foreseeable loss or damage.
This warranty is in addition to any other rights or remedies that the consumer may have under State or Federal
legislation.
IMPORTANT NOTE
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
IMPORTANT SAFETY INFORMATION
l Precise control of the L.E.Ds creates the correct beam pattern
for Australian roads
l Reinforced housing with no lament
l L.E.Ds life is over 30,000 hours
l In built IP rated fan provides optimised cooling (IP65)
l 4000 lumens (pair)
TECHNICAL SPECIFICATIONS
Voltage: 12/24V
L.E.Ds: Lumileds ZES
Colour Temperature: 5700°K
Lumens: 4000Lm per pair
IP Rating: IP65
Operating Temperature: -40°C to +80°C
Expected Life: 30,000 hours
P/No. 18424, 18427, 18427P, 18428
IMPORTANT SAFETY INFORMATION
Before installation please follow the recommended precautions below:
l Ensure the vehicle is parked on a level surface with the handbrake engaged.
l Allow the engine and engine bay to cool to eliminate any chance of burns.
l Disconnect the battery earth cable from the vehicles battery before
commencing installation or maintenance.
l Allow globes to cool before attempting to remove from headlamps (minimum
30 minutes recommended after use).
l Avoid touching the glass on halogen globes or the L.E.D chips on L.E.D globes.
l Do not attempt to switch the lamps on before all the connections are made.
2
3 Insert the lamp body in
the direction of arrow
INSTALL
1 3 Move off the chuck Connect the power
cable with original
car connector
H7 – P/Nos. 18427 / 18427P
2 Install and x the
socket
TROUBLESHOOTING
4 Screw the bulb on
clockwise
*Note: Some vehicles use a CANBUS system to detect when a globe is blown or faulty. L.E.D
globes draw a fraction of the current of standard halogen and incandescent globes. This may
cause some systems to think the globe is faulty, resulting in a warning light on the dash or
the lights ickering or pulsing. Please install the correct CANBUS module (sold separately) to
eliminate this problem.
Failure to install appropriate CANBUS module may cause an issue which may require
professional attention (i.e. Dealership, Auto Electrician).
Fault Solution
No illumination from
both L.E.D globes
Check battery earth cable has proper connection.
Check connections from vehicle
harness to Suret L.E.D globes.
No illumination from
one L.E.D globe
Check connections from vehicle
harness to Suret L.E.D globes.
Swap Suret L.E.D globe from other side, if the
globe illuminates the other globe may be faulty.
Partial illumination Check L.E.D globes for damage during installation
and ensure plug is tightly connected to harness
correctly.
Not enough light
on the road
Adjust vehicle headlights (refer to owner’s manual).
Lights ickering Install CANBUS* module (sold separately).
Resistors are also available if the issue continues
with a CANBUS installed.
Warning light on
dashboard coming on
Install CANBUS* module (sold separately) to cancel
warning light.
Resistors are also available if the issue continues
with a CANBUS installed.
5 Connect the power line
with the original car
lamp connector
2 Insert lamp body in
direction of arrow
1 Pull up the socket
6 Use an additional
connector cable if
necessary
H8 / H9 / H11 – P/No. 18428
1 Insert lamp body in
direction of arrow
2 Screw bulb on
clockwise
3 Connect the power
cable with original
car connector
H4 – P/No. 18424
Note: Once tted, test beam and adjust orientation if required by twisting.

Produktspecifikationer

Varumärke: Narva
Kategori: Inte kategoriserad
Modell: H7 Surefit

Behöver du hjälp?

Om du behöver hjälp med Narva H7 Surefit ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Narva Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer