Noise Engineering Cursus Iteritas Bruksanvisning

Läs nedan 📖 manual på svenska för Noise Engineering Cursus Iteritas (7 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/7
1
Type LFSR VCO
Size 10HP Eurorack
Depth 1.5 Inches
Power 2x8 Eurorack
+12 mA 150 / 80 (if 5v on)
-12 mA 5 / 5
+5 mA 0 / 90 (optional)
Noise Engineering
Cursus Iteritas
Dynamically generated wavetable oscillator using orthogonal functions.
Cursus Iteritas is an oscillator that works from a dynamically generated
wavetable. It gives the user spectral-like controls over three different modes
based on different conceptualizations of frequency: Fourier, which uses sine
waves; Daubechies, using wavelets, and Walsh mode, using the Walsh
transform. Cursus Iteritas parametrizes a wide variety of sounds, but because
the sounds are all based off of orthogonal functions, it has a musical tone
structure and can produce an extremely wide variety of harmonic sounds.
Interface
All knobs on Cursus Iteritas function as offsets for the input jacks. The controls
function similar to a bandpass filter; center, width, and tilt allow the filter to be
asymmetric.
Pitch
1v/8va pitch control. For more control, see Range below.
Center
selects the center harmonic used to build the wavetable.
Structure
allows selection of harmonics included in the output. In the center
position, all harmonics are included. Fully left only even harmonics; fully right,
only odd.
Edge
controls the oversampling filter of the wavetable. As this is turned to the
right, it will add musical overtones.
Fold
wavefolder. Enough said.
Width
controls how many different harmonics are used to create the wavetable.
Tilt
weights the spread of harmonics. In the middle it is symmetric; at left,
lower harmonics are louder while at right, higher harmonics get more volume.
Sync
triggers edge-based oscillator reset
Mode
selects which orthogonal function set is used to produce the wavetable
Range
two-octave offset pitch ranges
Out
audio output - 10vpp
Noise Engineering
Cursus Iteritas
Dynamically generated wavetable oscillator using orthogonal functions.
2
Noise Engineering
Cursus Iteritas
Dynamically generated wavetable oscillator using orthogonal functions.
Patch Tutorial 0 - Introduction
The easiest way to get to know Cursus is to just plug in the output and play with the knobs to get a
feel for the sounds it can make.
Patch Tutorial 1
Cursus works very well with any LFO, gate or envelope source the more the better. Patching the
outputs of the Numeric repetitor directly into the parameter inputs on Cursus is a great way to generate
complex rhythmic tonality variation.
Every LFO source is fun with Cursus. We highly reccomend patching Sinc Iter, Malekko Voltage
Block, Malekko AD/LFO, Mannequins Just Friends, Make Noise Wogglebug, and WMD PDO with
Cursus.
Patch Tutorial 1 - Gates and LFO
We will be updating this with
pictures, more examples and
videos very soon!
3

Produktspecifikationer

Varumärke: Noise Engineering
Kategori: Inte kategoriserad
Modell: Cursus Iteritas

Behöver du hjälp?

Om du behöver hjälp med Noise Engineering Cursus Iteritas ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Noise Engineering Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer