NUVO NV-SUBAMP200-NA Bruksanvisning

NUVO mottagare NV-SUBAMP200-NA

Läs nedan 📖 manual på svenska för NUVO NV-SUBAMP200-NA (14 sidor) i kategorin mottagare. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/14
Part Numbers
NV-SUBAMP100-xx
NV-SUBAMP200-xx
NV-SUBAMP500-xx
AMPLIFIER FEATURES
NV-SUBAMP100-xx
1 13 10
514 6 15 127
Fig. 1
NV-SUBAMP200-xx
19
5 12 11102071617
8
6 21415
Fig. 2
NV-SUBAMP500-xx
NOTE: Power mode, Volume control, Phase control, and Crossover control are accessed on the LCD display menu using the control knob.
19 2 3
219
12 111817 108 1020
Fig. 3
Installation Instructions
Nuvo In-Wall / In Ceiling Subwoofer Amplifiers
1507315 Rev A 20190328
2
1Status light
2LCD display
3Control knob
4Power mode switch
5Volume control
6Phase control
7Crossover control
8Low-level RCA input/
output jacks
9USB port
10 Voltage selector switch
11 Master power switch
12 Power cord inlet
13 WLS
14 High-level input
15
EQ selection:
A - NV-SUBIC8
B - NV-SUBIW8
C - SUBIWDUAL8
16 EQ mode
17 12 V DC trigger input/
output
18 IR
19 Power button
20 Sub terminal screws
21 Fuse
This instruction sheet covers the installation of the Nuvo In-Wall/In-Ceiling Subwoofer Amplifiers. These amplifiers offer a substantial amount of dynamic
power to increase the quality of your audio system.
UNDERSTANDING THE LCD PANEL FEATURES (FOR NV-SUBAMP500-XX MODELS)
Power Up Screen
Shows a message that the system is powering up.
Home Screen/Volume
Option for adjusting volume level.
Audio Mode Screen/Status
This setting has presets to put the amplifier into a mode that supports
your favorite listening environment. Choose one of the following options:
Music
Movie
Bypass
Night Mode Status
This setting places a low sound threshold on the system for evening use.
Off
On
Speaker EQ Screen
Select one of the following modes:
NVSUBIC8 1
NVSUBIW8 2
NVSUBIWDUAL8 3
Flat
3
Crossover Main Screen
Crossover provides an option for a low pass filter for the amplifier. Choose
from one of the following options:
LFE (Default setting)
40 - 250 HZ
Phase Screen
0-180
Lock Control Main Screen
Locks the menu for the amplifier controls to prevent accidental changes.
Off
On
Factory Reset
Yes: Resets all amplifier controls to the default settings.
No
Power Options Screen
This setting sets the power state. Choose from one of the following options:
The amplifier is always on. This is the default setting.Switch:
12 V Trigger: The amplifier turns on automatically upon receiving a 12 V
input signal. When the 12 V signal is removed, the amplifier automatically
goes into standby mode.
The amplifier turns on automatically upon receiving an Audio Sensor:
audio input signal. When the amplifier no longer receives a signal, it
automatically moves into a standby state after 15 minutes.
IR - Device ID
Assigns an IR ID between 1 and 4 to the amplifiers in the system.
1
2
3
4
Exit Menu Screen
Press the knob to exit the menu for the controls and bring up the Home/
Volume screen.

Produktspecifikationer

Varumärke: NUVO
Kategori: mottagare
Modell: NV-SUBAMP200-NA

Behöver du hjälp?

Om du behöver hjälp med NUVO NV-SUBAMP200-NA ställ en fråga nedan och andra användare kommer att svara dig




mottagare NUVO Manualer

mottagare Manualer

Nyaste mottagare Manualer