Ozito BDP-500 Bruksanvisning

Ozito Borrmaskin BDP-500

Läs nedan 📖 manual på svenska för Ozito BDP-500 (8 sidor) i kategorin Borrmaskin. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

DRILL

PRESS

500W 9 Speed

INSTRUCTION MANUAL

BDP -500

STANDARD EQUIPMENT

IN ORDER TO MAKE A CLAIM UNDER THIS

WARRANTY YOU MUST RETURN THE PRODUCT

TO YOUR NEAREST BUNNINGS WAREHOUSE WITH

YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY

PLEASE TELEPHONE OUR CUSTOMER SERVICE

HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

3 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 36 months from the

original date of purchase and is intended for DIY (Do It Yourself) use

only. If a product is defective it will be replaced in accordance with

the terms of this warranty. Warranty excludes consumable parts, for

example: feed wheel handles, keyed chuck, hex key, chuck key, belt.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other

than that speciﬁed on the tool.

• If the tool shows signs of damage or defects caused

by or resulting from abuse, accidents or alterations.

• Failure to perform maintenance as set out within the instruction

manual.

• If the tool is disassembled or tampered with in any way.

• Professional, industrial or high frequency use.

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE

HAVE THE MODEL NUMBER AND DATE OF

PURCHASE AVAILABLE. A CUSTOMER SERVICE

REPRESENTATIVE WILL TAKE YOUR CALL

AND ANSWER ANY QUESTIONS YOU MAY

HAVE RELATING TO THE WARRANTY POLICY

OR PROCEDURE.

OZITO Australia/New Zealand (Head Ofﬁce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The beneﬁts provided under this warranty are in addition

to other rights and remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded

at law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable

loss or damage. You are also entitled to have the goods repaired

or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

Generally you will be responsible for all costs associated with

a claim under this warranty, however, where you have suffered

any additional direct loss as a result of a defective product you

may be able to claim such expenses by contacting our customer

service helpline above.

ozito.com.au

0719

SPECIFICATIONS

Motor Size: 500W (S2 15min)

Input: 230 – 240V ~ 50Hz

No Load Speed: 500-2,500/min

Chuck: 16mm Keyed

Morse Taper: B16-2MT

Spindle Travel: 50mm

Spindle Shaft to

Column Distance: 115mm

Column Height: 625mm

Table Size: 168x168mm

Table Tilt: 0-45

0 (Left & Right)

Weight: 16.08kg

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

Assembling the drill press

1. Carefully remove contents from the packaging.

2. Select a rm, level surface on which

to assemble the drill press.

3. Place the base and align the column

over the large hole. Align the holes

in the column support with those

in the base and secure in place

using the 3 column support bolts

(supplied). Using a 14mm spanner

securely tighten all

3 column support bolts.

4. Slide the table support over the

column. Using the table support

lock, secure the table into the

desired position.

5. Lift the head assembly and slide it

down onto the column as far as it

will go. Rotate the head so that is

aligned with the base.

To secure in position install the 2

head lock screws. Tighten using

the 4mm Hex key, rotating in a

clockwise direction.

DRILL PRESS

KNOW YOUR PRODUCT

2120

1. ASSEMBLY

SETUP & PREPARATION

WARNING! DURING ASSEMBLY ENSURE THE

DRILL PRESS IS DISCONNECTED FROM THE

POWER SUPPLY.

ACCESSORIES

20. Chuck key

21. 4mm & 10mm

Hex key

1. Emergency Stop Button

2. Pulley cover screw

3. Feed wheel handles

4. Belt tension knob

5. Feed wheel hub

6. Column

7. 16mm Keyed chuck

8. Eye Shield

9. Table

10. Table support

11. Table support lock

12. Column support bolts x 3

13. Column support

14. Base

15. Head assembly

16. Depth indicator

17. ON/OFF Switch

18. Head lock screw

19. Chuck Key Holder

6. To t the eye shield, rst loosen the

phillips head screw on the shield

and then slide over the drill spindle.

Tighten the securing screw to lock

in position.

7. To t the feed wheel handles,

screw them into the feed

wheel hub.

8. To t the keyed chuck, rst place

a piece of timber on the table and

position the keyed chuck with the

jaws retracted under the drive

shaft. Raise the table toward

the drive shaft until the chuck is

approximately 25mm from the

drive shaft.

9. To secure the keyed chuck to the drive

shaft gently lower the drive shaft using

the feed wheel handles until the drive

shaft is pushed into the rear of the keyed

chuck. A gentle tap on the timber is

required to secure the keyed chuck onto

the tapered drive shaft.

Installing and removing drill bits

1. Using the chuck key, loosen the

jaws of the chuck by rotating in an

anti-clockwise direction.

2. Insert the drill bit fully into the

keyed chuck.

3. Whilst holding the drill bit in one

hand, rotate the top collar of

the keyed chuck in a clockwise

direction.

Ensure that you tighten all 3 holes

in the keyed chuck using the chuck

key to securely tighten the jaws and

hold the drill bit in position.

Approx. 25mm

Produktspecifikationer

Varumärke:	Ozito
Kategori:	Borrmaskin
Modell:	BDP-500

Behöver du hjälp?

Om du behöver hjälp med Ozito BDP-500 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Borrmaskin Ozito Manualer

Ozito BDP-500 Bruksanvisning

15 Oktober 2024

Ozito PXDDS-200 Bruksanvisning

30 September 2024

Ozito PXRHK-200 Bruksanvisning

26 Augusti 2024

Ozito PXDDK-070U Bruksanvisning

26 Augusti 2024

Ozito ZLHDK-150U Bruksanvisning

25 Augusti 2024

Ozito PXDDK-070 Bruksanvisning

24 Augusti 2024

Ozito PXBIS-320 Bruksanvisning

16 Augusti 2024

Ozito HDR-3000 Bruksanvisning

15 Augusti 2024

Ozito PXDDK-200 Bruksanvisning

12 Augusti 2024

Ozito SHD-3100 Bruksanvisning

7 Augusti 2024

Borrmaskin Manualer

Nyaste Borrmaskin Manualer

Black And Decker PF126 Bruksanvisning

27 Oktober 2024

Bosch GSR 120-LI Professional Bruksanvisning

24 Oktober 2024

Bosch gsr 18 2 li Bruksanvisning

23 Oktober 2024

Vonroc CD510DC Bruksanvisning

21 Oktober 2024

Einhell TC-CD 18/35 Li Bruksanvisning

20 Oktober 2024

Einhell Herocco Solo Bruksanvisning

19 Oktober 2024

DeWalt dc987ka Bruksanvisning

19 Oktober 2024

AEG KH 28 Super XE Bruksanvisning

18 Oktober 2024

MSW -DDM255 Bruksanvisning

16 Oktober 2024

MSW -DDM152 Bruksanvisning

16 Oktober 2024