Ozito ELM-1030U Bruksanvisning

Ozito Gräsklippare ELM-1030U

Läs nedan 📖 manual på svenska för Ozito ELM-1030U (3 sidor) i kategorin Gräsklippare. Denna guide var användbar för 11 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/3

ECOMOW

ELECTRIC MOWER

1000W 305mm

ORIGINAL INSTRUCTIONS

SPECIFICATIONS

Voltage: 220-240V~50/60Hz

Motor: 1000W

No Load Speed: 3,400/min

Cutting Width: 305mm

Cutting Heights: 3 levels, 30-70mm

Catcher Capacity: 25 litre

Power Cord Length: 10m

Protection Class: II

Weight: 7.97kg

ELM-1030U

WHAT’S IN THE BOX

Electric Lawn Mower

Handle Fasteners

Grass Catcher

General safety regulations for this electrical tool

This equipment is not allowed to be used by children. Children should be supervised so that they do not play with the

equipment. Children are not allowed to carry out the cleaning or maintenance. This equipment is not allowed to be used

by people with limited physical, sensory or mental capacities or by those with insufcient knowledge or experience unless

they are supervised or instructed by a person who is responsible for them.

Safety instructions for hand mower

• Before use, check the mains cable and extension cable for signs of damage and aging.

• If the cable is damaged during operation, disconnect it immediately from the power supply.

• Check the machine for signs of damage before use. Repairs may only be carried out by our service workshop. If unusual

vibrations occur during use, switch the machine off immediately and pull the plug. Check the cutters and clean them if

necessary. If the machine continues to vibrate, switch it off, disconnect it from the mains supply and send it to our service

workshop.

• The machine must not be tipped whilst it is being started. Both hands must be on the handle when you start the

machine.

• Worn parts may only be replaced by our service workshop. If necessary contact the service address provided.

WARNINGS

• Do not use the mower if the connection cable is damaged or worn.

• Do not use a damaged cable to connect the machine to the mains supply and do not touch a damaged cable whilst it is

connected to the mains. A damaged cable can result in contact with live parts.

• Do not touch the cutters until the machine has been disconnected from the mains and the cutters have reached a

complete standstill.

• Keep extension cables away from the cutters. The cutters can damage the cables and result in contact with live parts.

• Break the connection with the mains supply (in other words pull the plug out of the socket):

- whenever you leave the machine unattended;

- before released a blocked cutter;

- before inspecting or cleaning and before working on the machine;

- if a foreign body has been struck;

- whenever the machine starts to vibrate oddly.

• Carefully read the instructions for how to operate the machine safely.

• We recommend that the machine is only connected to a power supply protected by means of an earth

-leakage circuit breaker (RCD) with a maximum trip current of 30 mA.

Note

a) Read the directions with due care. Familiarize yourself with the operator controls and proper operation of the machine.

b) Never allow children or other persons who are not familiar with the operating instructions to use the mower. Contact

your local governmental agency for information regarding minimum age requirements for the user.

c) Never mow in the direct vicinity of persons

- especially children

- or animals.

d) Always keep in mind that the operator or user of the equipment is responsible for accidents involving other persons

and/or their property.

Preliminary measures

a) Always wear sturdy, non

-slip footwear and long trousers when mowing. Never mow barefoot or in sandals. Avoid wearing loosely tting clothes or

clothing with hanging belts or cords.

b) Check the ground on which the equipment will be used and remove all objects that could be caught up or violently

ung out.

c) Before using the scythe, visually inspect it to ensure that the blade, mounting bolts and the entire cutting apparatus are

in good working order (i.e. not worn out or damaged). To prevent any imbalance, replace worn out or damaged blades

and mounting bolts as a set only (if applicable). Worn or damaged cutting tools must be replaced.

d) Before use, check the power cable and extension cable for signs of damage and wear. If the cable is damaged

during operation, disconnect it immediately from the power supply. DO NOT TOUCH THE CABLE BEFORE IT IS

DISCONNECTED. Do not use the equipment if the cable is worn or damaged.

e) Remember that if the machine has several cutting tools, the movement of one cutting tool may result in the other

cutting tools starting to rotate.

Handling

a) Only mow in broad daylight or in well-lit conditions.

b) Do not use the machine on wet grass.

c) Always maintain good footing on inclines.

d) Only operate the machine at a walking pace.

e) Always mow across hills i.e. never straight up or straight down.

f) Be particularly careful when you change direction on a slope.

g) Do not mow on overly steep inclines.

h) Always be extra careful when turning the mower around and when pulling it towards you.

i) Switch the mower off , pull the plug and wait until the cutters have reached a complete standstill if you need to tip the

mower over, transport it over surfaces other than grass and if the mower has to be moved from and to the area you wish

to mow.

j) Never use the lawn mower if the guards are damaged or without the attached guards, e.g. deectors and/or grass

catching devices.

k) Use the ON/OFF switch carefully as described in the manufacturer’s instructions. Make sure that your feet are far

enough away from the mower blade!

l) The lawn mower should not be tilted when the motor is switch on unless it has to be raised for starting purposes. In this

case, tilt it as little as absolutely necessary and only raise the side opposite to that of the user.

m) Do not switch on the mower if you are positioned in front of the chute.

n) Never move your hands or feet toward or under any rotating parts. Keep clear of the chute opening at all times.

o) Never lift or carry a lawn mower with the engine running.

p) Switch off the motor and pull the plug out of the socket. Make sure that all moving parts have reached a complete

standstill:

- before you dislodge any blockages or clogs in the chute.

- before carrying out any checks, cleaning, maintenance or other work on the lawn mower.

- if you have struck a foreign object. Examine the mower for signs of damage and carry out any necessary repairs before

restarting and continuing to work with the mower.

- if the lawn mower begins to experience exceptionally strong vibrations, immediately switch it off and check it.

- Search for damage.

- Repair the damaged parts as required.

- Make sure that all nuts, bolts and screws are fastened securely.

q) Switch off the mower and pull the plug whenever you leave the mower.

Maintenance and storage

a) Make sure that all nuts, bolts and screws are tightened securely and that the machine is in safe working condition.

b) Allow the mower to cool before you put it into an enclosed area.

c) To avoid the risk of re, keep the motor housing and ventilation slots clear of grass, leaves, oil and grease.

d) Routinely check the grass basket for signs of wear and impaired functionality.

e) For your own safety, have worn or damaged parts replaced without delay.

f) Take care not to jam your ngers between moving cutting tools and stationary parts of the equipment while you are

adjusting the equipment.

g) While you are carrying out maintenance work on the cutting tools, remember that the cutting tools can still be moved

even if the power source has been switched off .

h) For your own safety, replace worn or damaged parts without delay. Use only original spare parts and original

accessories.

Ozito Industries will not be responsible for any damage or injuries

caused by repair of the tool by an unauthorised person or mishandling

or mistreatment of the tool. This tool is designed for Domestic Home Use

only. Use in commercial or industrial environments will void the warranty.

CAUTION!: ALWAYS HANDLE THE BLADE WITH CARE

– SHARP EDGES COULD CAUSE SERIOUS INJURY.

USE GLOVES.

MAINTENANCE

WARNING!: BEFORE CLEANING YOUR ECOMOW

ELECTRIC MOWER OR CARRYING OUT ANY

MAINTENANCE PROCEDURE, MAKE SURE THAT THE

MOTOR IS OFF AND THE TOOL DISCONNECTED FROM

THE POWER SUPPLY TO PREVENT ACCIDENTAL

STARTING.

Removing the Blade

1. To remove the blade bolt, hold the

blade rmly and with a 13mm socket

(not supplied) loosen the blade bolt

by turning it anti-clockwise.

Note: A piece of timber will assist in

holding the blade while removing or

tightening the blade bolt.

2. Remove the blade bolt and blade.

3. Inspect for damage and clean as

necessary.

Replace the metal blade after 50 hours mowing or 2 years whichever is

the sooner – regardless of condition. If the blade is cracked or damaged

replace it with a new one. Never use a blade bolt if the insulated head is

damaged, cracked or missing.

TIMBER

Fitting the Blade

• Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safe

working condition.

• Check the catcher frequently for wear or deterioration.

• Replace worn or damaged parts for safety.

• Only use the replacement blade, blade bolt, and impeller specied for this

product.

• Be careful during adjustments of the lawn mower to prevent entrapment of

the ngers between moving blade and xed parts of the machine.

• Oil the wheel pins.

• When not in use, the mower should be stored in a dry, frost-free location, out

of reach of children.If the housing of the mower requires cleaning, do not use

solvents but a moist soft cloth and brush only.

• Frequently check the wheel threads are rm and tight.

CAUTION!: DO NOT TOUCH ROTATING BLADES.

ADDITIONAL SAFETY INSTRUCTIONS FOR LAWN MOWERS

1. Fit the blade to the fan with the tilt edges of the blade facing towards the

mower, ensuring the blade is located onto the fan location lugs correctly.

2. Re-assemble blade bolt through blade and fan.

3. Hold the blade rmly and tighten blade bolt with a (not supplied), by turning

in a clockwise direction. The tightening torque should be approx. 25 Nm.

ozito-diy.co.uk

OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG

All of our products undergo strict quality checks to ensure that they reach

you in perfect condition. In the unlikely event that your device develops a

fault, please contact our service department at the address shown on this

guarantee card. You can also contact us by telephone using the customer

service number shown. Please note the following terms under which

guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the

manufacturer mentioned below promises to buyers of its new products

in addition to their statutory guarantee claims are not affected by this

guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or

manufacturing faults on a product which you have bought from the

manufacturer mentioned below are limited to either the rectication of said

defects on the product or the replacement of the product, whichever we

prefer.

Please note that our devices are not designed for use in commercial, trade

or professional applications. A guarantee contract will not be created if the

device has been used by commercial, trade or industrial business or has

been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly

instructions or due to incorrect installation, a failure to follow the operating

instructions (for example connecting it to an incorrect mains voltage or

current type) or a failure to follow the maintenance and safety instructions

or by exposing the device to abnormal environmental conditions or by lack

of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example

overloading the device or the use or unapproved tools or accessories),

ingress of foreign bodies into the device (such as sand, stones or dust,

transport damage), the use of force or damage caused by external forces

(for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural

wear or tear or by normal use of the device.

4. Your Product is guaranteed for a period of 36 months from the original

date of purchase and is intended for DIY (Do It Yourself) use only. Warranty

excludes consumable parts. Guarantee claims should be submitted

before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the

guarantee period. The original guarantee period remains applicable to the

device even if repairs are carried out or parts are replaced. In such cases,

the work performed or parts tted will not result in an extension of the

guarantee period, and no new guarantee will become active for the work

performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST

RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR

Please refer to the restrictions of this warranty concerning wearing parts,

consumables and missing parts as set out in the service information in

these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

WARRANTY

0917

SPARE PARTS

Spare parts can be ordered from the Special Orders

Desk at your local Bunnings Warehouse or Homebase

store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: info@ozito-diy.co.uk

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of re, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency,

before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the equipment to the mains supply make sure that the data on the rating plate are

identical to the mains data.

This tool is double insulated therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid

a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The

insulation system is for added protection against injury resulting from a possible electrical insulation failure

within the tool.

Using an Extension Lead

Please only use power cables that are not damaged. The total length of the power cable should not exceed

40 meters; going beyond this distance will reduce the power output of the electric motor. The power cable

must have a cross-section of 3 x 1.5 mm2. The insulating sheath of lawn mower power cables is frequently

damaged.

Some of the causes for this are:

• Cuts caused by running over the cable

• Pinching when the power cable is dragging under doors and pulled through windows.

• Cracking due to old age of the insulation

• Kinking by improperly fastening or guiding the power cable.

The power cables must, at the very minimum, be of type HO5RN-F and 3-stranded. The cable type must

be printed somewhere on the power cable. Only purchase power cables that are marked as such! Plugs

and socket couplers for the power cables must be made from rubber and be splash proof. There is a limit to

how long power cables can be. Longer power cables require larger conductor cross-sections. Power cables

and connecting lines must be regularly checked for damage. Ensure that the lines are de-energized before

checking them. Completely unwind the power cable. Also check power cable entry points, plugs and socket

couplers for kinks.

ELECTRICAL SAFETY

DESCRIPTION OF SYMBOLS

GENERAL POWER TOOL SAFETY WARNINGS

WARNING! “Read all safety warnings, instructions, illustrations and specications provided

with this power tool.” Failure to follow the warnings and instructions may result in electric shock,

re and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the

warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power

tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to

lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will

reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase

the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

nger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

h) Do not let familiarity gained from frequent use of tools allow you to become complacent and

ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Service

a. Have your power tool serviced by a qualied repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

SERVICE INFORMATION

Please note that the following parts of this product are subject to normal

or natural wear and that the following parts are therefore also required

for use as consumables.

* Not necessarily included in the scope of delivery!

Category Example

Wear parts* Carbon brushes, V-belt

Consumables* Blade

Missing parts

DECLARATION OF CONFORMITY

Gao/Product-ManagementWeichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Electric Lawn Mower ELM-1030U (Ozito)

2014/29/EU

2005/32/EC_2009/125/EC

2014/35/EU

2006/28/EC

X 2014/30/EU

2014/32/EU

2014/53/EC

2014/68/EU

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X 2011/65/EU

X 2006/42/EC

Annex IV

Notied Body:

Notied Body No.:

Reg. No.:

X 2000/14/EC_2005/88/EC

Annex V

X Annex VI

Noise: measured LWA = 93 dB (A); guaranteed LWA = 96 dB (A)

P = 1 KW; L/Ø = 30 cm

Notied Body: Société Nationale de Certication et DʼHomologation

S.A.R.L. (SNCH) (0499)

2012/46/EU

Emission No.:

Standard references: EN 60335-2-77; EN 62233;

EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 11.09.2017

First CE: 17 Archive-File/Record: NAPR017645

Art.-No.: 30.001.97 I.-No.: 11017 R. GehardDocuments registrar:

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric

and electronic equipment and its implementation in national laws, old

electric power tools have to be separated from other waste and disposed

of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the

owner of the electrical equipment must make sure that the equipment is

properly disposed of if p1-he no longer wants to keep the equipment. The old

equipment can be returned to a suitable collection point that will dispose

of the equipment in accordance with the national recycling and waste

disposal regulations. This does not apply to any accessories or aids

without electrical components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of

documentation and papers accompanying products is permitted only with

the express consent of the iSC GmbH.

Subject to technical changes.

Danger!

Sound and vibration

Sound and vibration values were measured in accordance

with the standards EN ISO 3744: 1995, EN ISO 11201: 1995, and EN ISO

20643: 2005.

Lpa at the operator position: 80.4 dB

Kpa uncertainty: 3 dB

Lwa sound power level 96 dB

Kwa uncertainty: 3 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions) determined in

accordance with EN 60745.

Vibration at the handles

Vibration emission value a

h = 2.285 m/s2

K uncertainty = 1.5 m/s2

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

Danger! Read the directions for use before

operating the equipment.

Caution! Keep all other persons a y from the wa

danger zone.

Caution! Sharp blades! Pull out the safety plug before

carrying out any repair work or if the p er cable is ow

damaged. The blades will continue to rotate after the motor

is switched off.

Caution! Keep the power cable a y from the cutters! wa

Guaranteed sound p er level: 96 dBow

Danger! Read the operating instructions to reduce the risk of injury

Protection class II

ADDITIONAL INFORMATION

Only replace the blade with a genuine Ozito replacement blade, as this will

ensure top performance and safety under all conditions.

TROUBLESHOOTING

Problem Cause Remedy

The motor

fails to start

The capacitor is

defective

The mower housing is clogged.

Have repaired by the Customer

Service Centre

There is no electricity

at the plug

Check the cable and the fuse

The cable is defective Check the cable

The combined switch/

plug is defective

Have repaired by the Customer

Service Centre

The connectors have

become separated

from the motor or the

capacitor

Have repaired by the Customer

Service Centre

The mower is standing

in high grass

Start in low grass or on an area

that has already been mowed;

change the cutting height if

necessary

Start in low grass or

on an area that has

already been mowed;

change the cutting

height if necessary

Clean the housing so that the

blade moves freely

The motor

performance

drops

The grass is too high

or too damp

Correct the cutting height

The mower housing is

clogged

Clean the housing

The blade is severely

worn

Replace the blade

Cutting is

irregular

The blade is worn Replace or re-sharpen the blade

Wrong cutting height Correct the cutting height

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

KNOW YOUR PRODUCT SETUP & PREPARATION

1. Motor cover

2. Lifting handle

3. Lower handle

4. Safety switch

5. Start/stop lever

6. Handle knobs

7. Grass catcher ap

8. Grass catcher

9. Handle securing set

10. Upper handle

2. ASSEMBLY 5. HOW TO MOW

ECOMOW ELECTRIC MOWER

To obtain the desired cutting height, the front and rear axles are

repositioned on the underside of the mower housing.

1. Press and hold the lock-off

button.

9 10

2 3 4

67 8

• Always use an approved extension lead suitable for power input

of this tool.

• Heavy duty power leads recommended not exceding 25m.

• While using your lawn mower always wear substantial footwear

and long trousers.

• Make sure the lawn is clear of sticks, stones, wire and debris;

they could be thrown by the blade.

• Before using the lawn mower and after any impact, check for

signs of wear or damage and repair as necessary.

• Replace a worn or damaged blade together with the blade bolt to

preserve balance.

WARNING!: ENSURE THE TOOL IS DISCONNECTED

FROM THE POWER SUPPLY BEFORE ASSEMBLY.

Fitting the Lower Handle to Mower Body

1. Fit the lower handle onto the

threaded ends.

1. First t the cord retainer, slide

it over the upper handle end

before xing the upper handle

to the lower handles.

1. Secure the power cord from the

switch housing to the mower using

cable ties (supplied).

To prevent accidental start up of the motor the mower is tted with a

dual action switch

2. To assemble the grass catcher

align the two halves and push

them together, one side at a

time. Ensure the two halves click

together around the entire middle

section.

1. Assemble the grass catcher

handle onto the opening

on the top half of the grass

catcher. The handle will click

into position when aligned

and tted correctly.

WARNING!: WHEN ASSEMBLING THE GRASS

CATCHER BACK TO THE MOWER AFTER

EMPTYING, ALWAYS ENSURE THERE IS NO BUILD

UP OF GRASS IN THE GRASS CHUTE. IF NEEDING TO

CLEAR THE GRASS, ALWAYS ENSURE THE MOWER

IS DISCONNECTED FROM THE POWER SUPPLY

PRIOR TO CLEARING. A BUILD UP OF GRASS IN THE

GRASS CHUTE MAY PREVENT GRASS FROM MOVING

INTO THE GRASS CATCHER EFFECTIVELY.

WARNING!: DISCONNECT THE MOWER FROM

THE POWER SUPPLY AND ENSURE THE BLADE

HAS STOPPED COASTING BEFORE ADJUSTING THE

HEIGHT.

Securing the Power Cord to the Handles

Assembling the Grass Catcher

“CLICK”

Fitting and Removing Grass Catcher

3. ADJUSTMENTS

Cutting Height Adjustment

4. SWITCHING ON/OFF

Start mowing the edge of the lawn

nearest to the power point so the

lead is laid out on the lawn you have

already cut.

For optimum grass collection, always mow in a straight line; do

not swing the lawn mower from side to side.

Mowing long thick grass may cause the motor speed to drop; you will

hear a change in the motor sound. If the motor speed drops you may

overload your lawn mower, which may cause damage. When mowing

in long thick grass rst cut with the cutting height set in the highest

position, this will help reduce the load.

Do Not Overload the Mower

Fitting the Upper Handle to the Lower Handle

3. To empty the grass catcher, lift

the catcher ap with one hand

then lift the grass catcher with

the other hand up off the two

raised housing clips.

The catcher must be attached to the two raised hooks on the mower.

1. Lift up the catcher ap with one

hand and guide the catcher over

the two hooks on the mower

housing.

2. Lower the grass catcher in place

and lower the catcher ap. The

catcher ap is held against the

gass catcher by a spring

WARNING! KEEP

POWER CORD AWAY

FROM BLADES.

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,

WE RECOMMEND THE USE OF A RESIDUAL CURRENT

DEVICE (RATED 30mA OR LESS).

2. Pull the Start/stop lever towards

the handle and hold in position,

the motor will now start.

3. Release the lock-off button

4. Release the Start/stop lever to

stop the mower.

1. Place the mower on its side.

2. Pull the wheel axle towards

the front of the mower.

3. Locate the wheel axle into

the desired cutting height

adjustment position.

2. Fit and secure in place with

the lower handle knobs.

Note: Make sure that front, back,

left & right wheels are located in

the same cutting height adjustment

position.

Cutting Height Positions

1 - 30mm (lowest).

2 - 50mm.

3 - 70mm (highest).

2. Place the upper handle over

the upper ends of the lower

handle. From the handle

securing set, t the bolts

through the inner side of

the lower handle and then

through the holes in the upper

handle. Secure in place by

screwing the handle securing

knobs over the protruding

ends of the bolts.

WARNING! THE BLADE WILL STOP A FEW

SECONDS AFTER THE SWITCH HAS BEEN

RELEASED. BE AWARE OF THE NECESSARY TIME IT

TAKES FOR THE BLADE TO STOP. DO NOT ATTEMPT

TO STOP THE BLADE.

Overload Protection

The mower has an internal cut off switch which will stop the operation

of the motor temporarily if too high in temperature. This cut off switch

will suddenly stop the motor from operating should the motor become

too hot during the operation of the mower.

First disconnect the mower from the power supply and inspect blade

for any obstructions.

A wait of 10 minutes in cooling time, or longer depending on ambient

temperature and the operation being performed, before switching On

the mower and resuming normal operation.

ELM-1030U

1. BEFORE USE

Items Supplied

Please check that the article is complete as specied in the scope of delivery.

If parts are missing, please contact our service centre or the sales outlet

where you made your purchase at the latest within 5 working days after

purchasing the product and upon presentation of a valid bill of purchase.

Also, refer to the warranty table in the service information at the end of the

operating instructions.

• Open the packaging and take out the equipment with care.

• Remove the packaging material and any packaging and/or transportation

braces (if available).

• Check to see if all items are supplied.

• Inspect the equipment and accessories for transport damage.

• If possible, please keep the packaging until the end of the guarantee period.

Danger!

The equipment and packaging material are not toys. Do not let children

play with plastic bags, foils or small parts. There is a danger of

swallowing or suffocating!

Proper Use

The lawn mower is intended for private use i.e. for use in home and

gardening environments.

Private use of the lawn mower refers an annual operating time generally not

exceeding that of 50 hours, during which time the machine is primarily used

to maintain small-scale, residential lawns and home/hobby gardens. Public

facilities, sporting halls, and agricultural/forestry applications are excluded.

Important. Due to the high risk of bodily injury to the user, the lawn mower

may not be used to trim bushes, hedges or shrubs, to cut scaling vegetation,

planted roofs, or balcony-grown grass, to clean (suck up) dirt and debris

off walkways, or to chop up tree or hedge clippings. Moreover, the lawn

mower may not be used as a power cultivator to level out high areas such as

molehills.

For safety reasons, the lawn mower may not be used as a drive unit for other

work tools or toolkits of any kind, unless they have been expressly permitted

by the manufacturer.

The equipment is to be used only for its prescribed purpose. Any other use is

deemed to be a case of misuse. The user / operator and not the manufacturer

will be liable for any damage or injuries of any kind caused as a result of this.

Please note that our equipment has not been designed for use in commercial,

trade or industrial applications. Our warranty will be voided if the machine is

used in commercial, trade or industrial businesses or for equivalent purposes.

Caution!

Residual risks

Even if you use this electric power tool in accordance with instructions,

certain residual risks cannot be rules out. The following hazards may

arise in connection with the equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.

2. Damage to hearing if no suitable ear protection is used.

3. Health damage caused by hand-arm vibrations if the equipment is used

over a prolonged period or is not properly guided and maintained.

Warning!

This equipment generates an electromagnetic eld during

operation. Under certain circumstances this eld may actively or

passively impede medical implants. To reduce the risk of serious

or fatal injuries, we recommend persons with medical implants to

consult their doctor and the manufacturer of the medical implant

prior to using the equipment.

OPERATION

Produktspecifikationer

Varumärke:	Ozito
Kategori:	Gräsklippare
Modell:	ELM-1030U
Enhetsplacering:	Vrijstaand
Färg på produkten:	Wit
Dörrgångjärn:	Rechts
Inbyggd display:	Nee
Vikt:	31740 g
Bredd:	545 mm
Djup:	580 mm
Höjd:	850 mm
Nettoskatt:	100 W
Ljudnivå:	40 dB
Energie-efficiëntieklasse:	D
Årlig-energiförbrukning:	111 kWu
Förpackningens vikt:	33380 g
Förpackningens bredd:	570 mm
Djuppackning:	596 mm
Förpackningshöjd:	885 mm
Dörröppningsriktning utbytbar:	Ja
Lämplig för paneljustering:	Nee
Kylskåpets nettokapacitet:	102 l
Typ av lampa:	LED
Antal hyllor i kylskåp:	2
Antal-grönsakslådor:	1
Temperaturlarm:	Nee
Äggställ:	Ja
Flaskställ:	Nee
Inget frostsystem:	Nee
Kylskåpsdörrfickor:	3
Till fackområdet:	Nee
Larm för öppen dörr:	Ja
Klimaatklasse:	N-ST
Bulleremissionsklass:	C
Justerbara fötter:	Ja
Ursprungsland:	China
Vattendispenser:	Nee
Energieffektivitetsskala:	A tot G