Ozito MWR-090 Bruksanvisning

Ozito Svetsmaskin MWR-090

Läs nedan 📖 manual på svenska för Ozito MWR-090 (8 sidor) i kategorin Svetsmaskin. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

GASLESS

MIG WELDER

90 Amp

INSTRUCTION MANUAL

SPECIFICATIONS

Input Voltage: 240V ~ 50Hz

Welding Current: 65 - 90Amp

Welding Wire Size: 0.8-0.9mm Flux-Cored Wire

Duty Cycle: 25%@90A

Insulation Type: Earthed Appliance (Class I)

Wire Spool Weight: 0.2kg to 5kg

Weight (tool only): 16.7kg

MWR-090

WHAT’S IN THE BOX

MIG Welder

Wire Feed Roller

Mig Wire

Welding Mask

Chipping Hammer /

Wire Brush

ozito.com.au

IN ORDER TO MAKE A CLAIM UNDER THIS

WARRANTY YOU MUST RETURN THE PRODUCT

TO YOUR NEAREST BUNNINGS WAREHOUSE WITH

YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY

PLEASE TELEPHONE OUR CUSTOMER SERVICE

HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

3 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 36 months from

the original date of purchase. If a product is defective it will

be replaced in accordance with the terms of this warranty.

Warranty excludes consumable parts, for example: Welding tips,

torch nozzles, ﬂexible inner tube, welding wire, wire feed rollers,

welding lenses, wire brushes and chipping hammer.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other

than that speciﬁed on the tool.

• If the tool shows signs of damage or defects caused

by or resulting from abuse, accidents or alterations.

• Failure to perform maintenance as set out within the

instruction manual.

• If the tool is disassembled or tampered with in any way.

• Professional, industrial or high frequency use.

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE

HAVE THE MODEL NUMBER AND DATE OF

PURCHASE AVAILABLE. A CUSTOMER SERVICE

REPRESENTATIVE WILL TAKE YOUR CALL

AND ANSWER ANY QUESTIONS YOU MAY

HAVE RELATING TO THE WARRANTY POLICY

OR PROCEDURE.

OZITO Australia/New Zealand (Head Ofﬁce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The beneﬁts provided under this warranty are in addition

to other rights and remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded

at law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable

loss or damage. You are also entitled to have the goods repaired

or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

Generally you will be responsible for all costs associated with

a claim under this warranty, however, where you have suffered

any additional direct loss as a result of a defective product you

may be able to claim such expenses by contacting our customer

service helpline above.

1014

MIN

MAX

MIN

MAX

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

The MIG welder is supplied with a 0.2kg coil of 0.8mm gasless

welding wire. Welding wire up to 5kg can be tted to this

welder.

MIG WELDER

ACCESSORIES

1 Internal Cooling Fan

2 Side Cover Release Lever

3 Side Cover

4 On/Off Switch

5 Overload Protection LED

6 Voltage Control Switch

7 Carry Handle

8 MIG Torch

9 Torch Tip

10 Earth Clamp

11 Shroud

12 Wire Feed Speed & Current

Adjustment Knob

13 Power Cord

14 Welding Mask

15 Chipping Hammer / Wire

Brush

16 Wire Feed Roller 0.8-0.9mm

(Fitted)

17 Mig Wire

KNOW YOUR PRODUCT

FITTING THE WELDING WIRE COIL

SETUP & PREPARATION

1 2 3 4 5 6 7

14 15 16

WARNING: ENSURE THE TOOL IS SWITCHED OFF AND

DISCONNECTED FROM THE POWER SUPPLY BEFORE

PERFORMING ANY OF THE FOLLOWING STEPS.

2 Remove the retaining nut

by rotating anti-clockwise

and remove the spring

and drive washer.

4 Align the spring and drive

washer lug with the slot in

the drive shaft and secure

with the retaining nut, but

do not over tighten.

1 Open the side cover

by lifting the side

cover release lever.

3 Slide the welding

wire coil onto the

shaft.

Note: Over tightening of the retaining nut will restrict the wire

feed rate and can cause damage to the wire feed motor or

irregular welding.

8 9 10 12 1311

2. WIRE DRIVE ROLLER SIZE 3. FEEDING THE WELDING WIRE

OPERATION

2 Pull the pressure screw

arm down and raise the

pressure arm.

1 With the pressure arm

raised away from the drive

roller, feed the welding

wire into the inlet guide

and between the wire

drive rollers.

4 Lift the wire drive roller off

the shaft and inspect it to

conrm the wire groove

size stamped on either

face. Always ensure the

wire drive roller size you

require is facing outward

when assembled.

3 Push the pressure arm

downward and raise the

pressure arm screw.

There are two different size rollers grooves machined into the

outer surface of the wire drive roller for a gasless MIG welder.

Flux-cored welding wire (0.8 - 0.9mm) is required to operate

this welder.

1 Release the pressure

of the pressure roller

by loosening the

adjustable pressure

screw anti-clockwise. Ensure the welding wire is free from any kinks and bends by

removing any damaged wire. When cutting the wire, ensure it

is not cut at an angle. It is recommended you lightly le the at

end of the wire prior to feeding.

3 Remove the wire

drive roller bracket by

rotating anti-clockwise

and then pulling

outwards.

2 Pass the wire through

the conduit liner,

ensuring the wire

is positioned in the

groove of the drive

roller.

4 Tighten the adjustable

pressure screw so

that the screw is

about half way down.

5 Secure the wire drive

roller by tting the

drive roller bracket

and fasten by rotation

clockwise.

Note: Do not over tighten the drive roller bracket as this could

damage the MIG welder.

CAUTION: IT IS CRITICAL THAT YOU CHOOSE THE

CORRECT WIRE DRIVE ROLLER SIZE.

WARNING: ENSURE THAT YOU DO NOT MAKE CONTACT

WITH THE EARTH CLAMP AT ANY STAGE WHEN

FEEDING THE WELDING WIRE THROUGH THE MIG

TORCH. THE ELECTRODE WIRE WILL BE AT WELDING

VOLTAGE WHILST IT IS BEING FED THROUGH THE

WELDER. KEEP THE MIG TORCH AWAY FROM YOUR

EYES AND FACE.

WARNING: THE POWER SUPPLY FOR THIS PRODUCT SHOULD

BE PROTECTED BY A RESIDUAL CURRENT DEVICE (RATED AT

30MA OR LESS). A RESIDUAL CURRENT DEVICE REDUCES THE

RISK OF ELECTRIC SHOCK.

Produktspecifikationer

Varumärke:	Ozito
Kategori:	Svetsmaskin
Modell:	MWR-090
Bredd:	305 mm
Djup:	203 mm
Typ av strömkälla:	ATX
Antal USB 2.0-portar:	6
Mikrofon, linjeingång:	Ja
Antal Ethernet LAN (RJ-45)-portar:	1
Certifiering:	FCC, CE, WHQL
Processoruttag:	LGA 775 (Socket T)
Processorfabrikant:	Intel
Maximalt internminne:	16 GB
Kompatibla operativsystem:	Win 7, Vista, XP
Ljudutgångskanaler:	7.1 kanalen
Nätverksfunktioner:	10/100/1000 Mbit
Ljudchip:	VIA VT1708S
PCI Express x1-platser:	2
PCI Express x16-platser:	1
S/PDIF-utgång:	Ja
PS/2-port(ar):	2
LAN-kontroller:	Realtek RTL8111D(L)
Icke-ECC:	Ja
PCI-platser:	2
Kompatibla processorer:	Intel® Celeron®
Moderkorts formfaktor:	ATX
Antal minnesplatser:	4
BIOS-minnesstorlek:	64 Mbit
COM-anslutningar:	1
Anslutning för CPU-kylare:	Ja
ATX-strömkontakt (24-stift):	Ja
Strömförsörjningsfläktanslutning:	Ja
Antal SATA-anslutningar:	6
USB 2.0-anslutningar:	3
Anslutning för diskettstation:	Ja
S/PDIF-ingång:	Ja
CD/AUX-ljudspel:	Ja